[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.

[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <tong.cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures

[How]
Add nsl_bpg_offset and rbs_min computation
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce

[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c
Signed-off-by: NChiawen Huang <chiawen.huang@amd.com>
Reviewed-by: NTony Cheng <tong.cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.

[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: NHarmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching

[how]
Use existing override logic.  If override not defined, then force
min = 507
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For better readability and reusability

[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NFatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

A regression caused dsc to never get disabled in certain situations.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen

[how]
Fix up the values before programming HW
Signed-off-by: NJun Lei <jun.lei@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
To add support for OS requirement to set preferred link training
parameters.

[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.
Signed-off-by: NDavid Galiffi <David.Galiffi@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU.  we optimize away
notifying SMU about no pstate, and so they will get stuck

[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Since we are using the signed FW now, and also using PSP firmware loading,
but it's still potential to break driver when loading FW directly
instead of PSP, so we should add offset.
Signed-off-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In function __ttm_dma_alloc_page(), d_page->addr is allocated
by dma_alloc_attrs() but freed with use dma_free_coherent() in
__ttm_dma_free_page().
Use the correct dma_free_attrs() to free d_page->vaddr.
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v2:
set average clock value on level 1 when current clock equal
min or max clock (fine grained dpm support).

the navi10 gfxclk (sclk) support fine grained DPM,
so use level 1 to show current dpm freq in sysfs pp_dpm_xxx
Signed-off-by: NKevin Wang <kevin1.wang@amd.com>
Reviewed-by: NKenneth Feng <kenneth.feng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

this function is not needed any more. error injection is
the only way to validate ras but it can't be executed in
amdgpu_ras_init, where gpu is even not initialized
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

error injection to other IP blocks (except UMC) will be enabled
until RAS feature stablize on those IP blocks
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

GFX RAS has not been stablized yet. disable GFX ras until
it is fully funcitonal.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

driver shouldn't init any ras debugfs/sysfs node for ASICs that don't have ras
hardware ability
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

With gfxclk or uclk dpm disabled, it's reasonable to report bootup clock
as the max supported.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The GDS and GWS blocks default to allowing all VMIDs to
access all entries. Graphics VMIDs can handle setting
these limits when the driver launches work. However,
compute workloads under HWS control don't go through the
kernel driver. Instead, HWS firmware should set these
limits when a process is put into a VMID slot.

Disable access to these devices by default by turning off
all mask bits (for OA) and setting BASE=SIZE=0 (for GDS
and GWS) for all compute VMIDs. If a process wants to use
these resources, they can request this from the HWS
firmware (when such capabilities are enabled). HWS will
then handle setting the base and limit for the process when
it is assigned to a VMID.

This will also prevent user kernels from getting 'stuck' in
GWS by accident if they write GWS-using code but HWS
firmware is not set up to handle GWS reset. Until HWS is
enabled to handle GWS properly, all GWS accesses will
MEM_VIOL fault the kernel.

v2: Move initialization outside of SRBM mutex
Signed-off-by: NJoseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

exposing fica registers to poll df pie data for xgmi error counters for
vega20.
Signed-off-by: NJonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: NAlexander Deucher <Alexander.Deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This can avoid them to be handled in a wrong way without notice.
Since not all SMU messages/clocks are supported on every SMU11 ASIC.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Current implementation is not actually able to detect
invalid message/table/workload mapping.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Current support will only work in internal engineering
boards.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

These were dropped and the headers never got cleaned up.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add all VCN instances' decode/encode/jpeg decode rings into
drm_sched_rq list.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Reviewed-by: NBoyuan Zhang <boyuan.zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

GPU cache info (part of virtual CRAT) size depends on CU number.
For arcturus, CU number has been increased. So the required memory
for vcrat also increases.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NYong Zhao <Yong.Zhao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The more 6 sdma instances work fine now with DF fix in vbios:
  * mmDF_PIE_AON_MiscClientsEnable(0x1c728)=0x3fe(DF_ALL_INSTANCE)
       [9:4]MmhubsEnable=3f (change from 0)
Signed-off-by: NLe Ma <le.ma@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ACC VGPRs are a secondary VGPR set of same size as the primary VGPRs.
Save them as a block immediately following VGPRs.
Signed-off-by: NJay Cornwall <Jay.Cornwall@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

With the printing, we don't need to parse the value on our own any more.
Signed-off-by: NYong Zhao <Yong.Zhao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add pci device ids.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NYong Zhao <Yong.Zhao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Another 6 sdma instances do not work at present. Disable them to unblock KFD
for silicon bringup as a workaround
Signed-off-by: NLe Ma <le.ma@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

They are not needed by arct
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

CWSR (compute wave save/restore) is used for
preempting compute queues.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

xgmi dpm is handled by the SMU.
Signed-off-by: NYong Zhao <Yong.Zhao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

CPG firmwares are not used.
Signed-off-by: NLe Ma <le.ma@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

arct has 4KB gds (4 banks inside) so the max_wave_id
should be 0xfff
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NLe Ma <Le.Ma@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Any dce register read back from arct is invalid. use hard code
stolen memory for arct until we validate the s3.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NLe Ma <Le.Ma@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Properly set the external silicon revision id.
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NLe Ma <Le.Ma@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>