Allocate the send buffer in a NUMA aware way.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate the receive bufer from the NUMA node assigned to the primary
channel.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove automatic variable 'err' in register_netevent_notifier() and
return the result of atomic_notifier_chain_register() directly.
Signed-off-by: NWang Long <long.wanglong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next, they are:

1) default CONFIG_NETFILTER_INGRESS to y for easier compile-testing of all
   options.

2) Allow to bind a table to net_device. This introduces the internal
   NFT_AF_NEEDS_DEV flag to perform a mandatory check for this binding.
   This is required by the next patch.

3) Add the 'netdev' table family, this new table allows you to create ingress
   filter basechains. This provides access to the existing nf_tables features
   from ingress.

4) Kill unused argument from compat_find_calc_{match,target} in ip_tables
   and ip6_tables, from Florian Westphal.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: misc improvements

These patches are highly inspired by changes from Petri on bcmgenet, last patch
is a misc fix that I had pending for a while, but is not a candidate for 'net'
at this point.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Occasionnaly we may get oversized packets from the hardware which exceed
the nomimal 2KiB buffer size we allocate SKBs with. Add an early check
which drops the packet to avoid invoking skb_over_panic() and move on to
processing the next packet.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, bcm_sysport_desc_rx() calls bcm_sysport_rx_refill() at the end of Rx
packet processing loop, after the current Rx packet has already been passed to
napi_gro_receive(). However, bcm_sysport_rx_refill() might fail to allocate a new
Rx skb, thus leaving a hole on the Rx queue where no valid Rx buffer exists.

To eliminate this situation:

1. Rewrite bcm_sysport_rx_refill() to retain the current Rx skb on the
Rx queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.

2. Modify bcm_sysport_desc_rx() to call bcm_sysport_rx_refill() at the
top of Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.

This is loosely inspired from d6707bec ("net: bcmgenet: rewrite
bcmgenet_rx_refill()")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a 1:1 mapping between the software maintained control block in
priv->rx_cbs and the buffer address in priv->rx_bds, such that there is
no need to keep computing the buffer address when refiling a control
block.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete jump to a label on the next line, when that label is not
used elsewhere.

A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier l;
@@

-if (...) goto l;
-l:
// </smpl>

Also remove the unnecessary ret variable.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The thunderx ethernet driver fails to build on architectures
that do not have an atomic readq() and writeq() function for
64-bit PCI bus access:

drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_reg_read':
include/asm-generic/io.h:195:23: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]

It seems impossible to get this driver to work on most 32-bit
hardware, so it's better to add an explicit dependency, in
order to let us keep building 'allmodconfig' kernels on
all architectures.

As the driver is meant for the internal hardware on an arm64 SoC, this
is not a problem for usability. Allowing the build on all 64-bit
architectures rather than just CONFIG_ARM64 on the other hand means that
we get the benefit of build testing on x86.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver update, May 28, 2015

The 1st patch fixes an issue with a function running DPDK overriding
broadcast steering rules set by other functions. Please add this one
to your -stable queue.

The rest of the series from Matan and Ido deals with scaling the number
of IRQs that serve RoCE applications to be in par with the Ethernet driver.

changes from V0:
 - addressed feedback from Sergei, removed extra blank line in patch #4
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When freeing a CQ, we need to make sure there are no
asynchronous events (on the ASYNC EQ) that could
relate to this CQ before freeing it.

This is done by introducing synchronize_irq.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that EQs management is in the sole responsibility of mlx4_core,
the IRQ affinity hints configuration should be in its hands as well.
request_irq is called only once by the first consumer (maybe mlx4_ib),
so mlx4_en passes the affinity mask too late. We also need to request
vectors according to the cores we want to run on.

mlx4_core distribution of IRQs to cores is straight forward,
EQ(i)->IRQ will set affinity hint to core i.
Consumers need to request EQ vectors, according to their cores
considerations (NUMA).
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, mlx4_en allocated EQs and used them exclusively.
This affected RoCE performance, as applications which are
events sensitive were limited to use only the legacy EQs.

Change that by introducing an EQ pool. This pool is managed
by mlx4_core. EQs are assigned to ports (when there are limited
number of EQs, multiple ports could be assigned to the same EQs).

An exception to this rule is the ASYNC EQ which handles various events.

Legacy EQs are completely removed as all EQs could be shared.

When a consumer (mlx4_ib/mlx4_en) requests an EQ, it asks for
EQ serving on a specific port. The core driver calculates which
EQ should be assigned to that request.

Because IRQs are shared between IB and Ethernet modules, their
names only include the PCI device BDF address.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SRIOV, when simple (i.e - Ethernet L2 only) flow steering rules are
created, always create them at MLX4_DOMAIN_NIC priority (instead of
the real priority the function created them at). This is done in order
to let multiple functions add broadcast/multicast rules without
affecting other functions, which is necessary for DPDK in SRIOV.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2015-05-28

Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:

 - All sorts of cleanups & fixes to ieee802154 and related drivers
 - Rework of tx power support in ieee802154 and its drivers
 - Support for setting ieee802154 tx power through nl802154
 - New IDs for the btusb driver
 - Various cleanups & smaller fixes to btusb
 - New btrtl driver for Realtec devices
 - Fix suspend/resume for Realtek devices

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
net/mlx5: ConnectX-4 100G Ethernet driver

This patchset extends the mlx5_core driver to support Ethernet
functionality. The Ethernet functionality in the mlx5 driver is
integrated into the core driver and not as separated driver. The
IB functionality remains in the mlx5_ib driver as before.

This functionality will enable the Ethernet capability of Mellanox's new
famility of cards - ConnectX-4. Due to the fact that backword
compatability is being kept, existing Connect-IB cards that are using
this driver are fully working with the modified driver, and no issues
with current deployments should be seen.

Like the ConnectX-3 cards, ConnectX-4 is a VPI (Virtual Port Interface -
every port can be configured as Infiniband or Ethernet) card.
Unlike previous generations, the ConnectX-4 has a separate PCI function
per port.

The current code has a limitation that Infiniband and Ethernet port types
are mutually exclusive. When the driver is compiled with Ethernet
support, the Infiniband functionality is disabled and vice versa. To
control that we added the CONFIG_MLX5_CORE_EN config directive
which is 'n' by default, but can be changed by the user.

This limitation is short-lived and would be addressed soon.

As part of this patchset, mlx5_ifc.h was heavily modified [1]. This file
is now generated automatically from the device specification document.
Since this patch is too big for the mail server, it might be missing in
the mailing list, but could be pulled from an external git repository [2].

irq name selection is done at driver initialization and doesn't contain the
interface name as part of the irq name.
irq_balancer will still work thanks to an improvement introduced by Neil Horman
[3] to use sysfs instead of /proc/interrupts.

Patchset was applied on top of commit ed2dfd90 ("tcp/dccp: warn user for
preferred ip_local_port_range")

[1] - Patch 4/11 ("net/mlx5_core: HW data structs/types definitions preparation for mlx5 ehternet driver")
[2] - http://git.openfabrics.org/?p=~amirv/linux.git;a=shortlog;h=refs/heads/mlx5e_v1
[3] - kernel: da8d1c8b PCI/sysfs: add per pci device msi[x] irq listing (v5)
      irq_balancer: 32a7757 Complete rework of how we detect and classify irqs

Thanks to Achiad, Saeed, Yevheny, Or and the whole team for making this happen,
Amir

Changes from V4:
- Removed Patch 3/12: net/mlx5_core: Add EQ renaming mechanism
- Patch 12/12: net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality
  - irq name is created on driver initialization, therefore it won't contain
    the network interface name in it. This won't effect irq_balancer thanks to
    patches introduced by Neil Horman to use sysfs instead of /proc/interrupts.

Changes from V3:
- PATCH 8/11: net/mlx5_core: Set/Query port MTU commands
  - Return value directly - no need for err.

Changes from V2:
- Improved changelogs and cover-letter
- Added CONFIG_MLX5_EN to disable/enable the Ethernet functionality
- Moved en.h and wq.[ch] into the patch with data-path related code

Changes from V1:
- Added patch 1/12 ("net/mlx5_core,mlx5_ib: Do not use vmap() on coherent
  memory")

Changes from V0:
- Removed V0 Patch 1/11 ("net/mlx5_core: Virtually extend work/completion queue
  buffers by one page") due to misuse of DMA API. Thanks Dave.
- Patch 1/11 ("net/mlx5_core: Set irq affinity hints"):
  - Use kcalloc instead of kzalloc
  - Fix build error when CONFIG_CPUMASK_OFFSTACK=n. Driver loading will fail
    now if cpumask allocation is failing.
  - Using dev_to_node helper. Thanks, Ido.
- Patch 3/11 ("net/mlx5_core: HW data structs/types definitions preparation for
  mlx5 ehternet driver")
  - Removed Mellanox internal comment at the head of the file. Thanks Joe
- Patch 6/11 ("net/mlx5_core: Implement get/set port status")
  - Use direct return of function's result. Thanks Sergei.
- Added Patch 8/11 ("net/mlx5_core: Set/Query port MTU commands")
- Patch 9/11 ("net/mlx5: Ethernet Datapath files")
  - Use rq->wqe_sz instead of skb_end_offset. Thanks Ido.
  - Use dma_wmb() when possible instead of wmb(). Thanks Alex.
  - Fix checkpatch issues
- Patch 10/11 ("net/mlx5: ethernet resources handling")
  - checkpatch issues
  - Added missing include
- Patch 11/11 ("net/mlx5: Ethernet driver")
  - checkpatch issues
  - fixed typo
  - Modified use of affinity hint
  - Using dev_to_node helper. Thanks, Ido.
  - Use new hardware commands from Patch 8/11 ("net/mlx5_core: Set/Query port
    MTU commands") to get/set port MTU in hardware.
  - Removed NETIF_F_SG since hardware ring wraparound is not supported
  - Use dma_wmb() when possible instead of wmb(). Thanks Alex.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the Ethernet part of the driver for the Mellanox ConnectX(R)-4
Single/Dual-Port Adapter supporting 100Gb/s with VPI.  The driver
extends the existing mlx5 driver with Ethernet functionality.

This patch contains the driver entry points but does not include
transmit and receive (see the previous patch in the series) routines.

It also adds the option MLX5_CORE_EN to Kconfig to enable/disable the
Ethernet functionality. Currently, Kconfig is programmed to make
Ethernet and Infiniband functionality mutally exclusive.
Also changed MLX5_INFINIBAND to be depandant on MLX5_CORE instead of
selecting it, since MLX5_CORE could be selected without MLX5_INFINIBAND
being selected.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contains the resource handling files:
- flow_table.c: This file contains the code to handle the low level API
		to configure hardware flow table. It is separated from
		the flow_table_en.c, because it will be used in the
		future by Raw Ethernet QP in mlx5_ib too.
- en_flow_table.[ch]: Ethernet flow steering handling. The flow table
		object contain a mapping between flow specs and TIRs.
		This mechanism will be used also to configure e-switch
		in the future, when SR-IOV support will be added.
- transobj.[ch] - Low level functions to create/modify/destroy the
                  transport objects: RQ/SQ/TIR/TIS
- vport.[ch] - Handle attributes of a virtual port (vPort) in the
  embedded switch. Currently this switch is a passthrough, until SR-IOV
  support will be added.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_[rt]x.c contains the data path related code specific to tx or rx.
en_txrx.c contains data path code which is common for both the rx and
tx, this is mainly napi related code.

Below are the objects that are being used by the hardware and the driver
in the data path:

Channel - one channel per IRQ. Every channel object contains:
  RQ  - describes the rx queue
  TIR - One TIR (Transport Interface Receive) object per flow type. TIR
        contains attributes for a type of rx flow (e.g IPv4, IPv6 etc).
        A flow is defined in the Flow Table.
        Currently TIR describes the RSS hash parameters if exists and LRO
        attributes.
  SQ  - describes the a tx queue. There is one SQ (Send Queue) per
        TC (traffic class).
  TIS - There is one TIS (Transport Interface Send) per TC.  It
        describes the TC and may later be extended to describe more
	transport properties.

Both RQ and SQ inherit from the object WQ (work queue). This common code
to describe the layout of CQE's WQE's in memory is in the files wq.[cj]

For every channel there is one NAPI context that is used for RX and
for TX.

Driver is using netdev_alloc_skb() to allocate skb's.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce set/Query low level functions to access MTU in hardware. To be
used by the netdev.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce mlx5_core_modify_cq_moderation() to be used by the netdev, to
set hardware coalescing.
Signed-off-by: NRana Shahout <ranas@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implemet get/set port status low level functions to be exposed by the
netdev.
Signed-off-by: NRana Shahout <ranas@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Those registers will be used by the ethtool to set/get settings.
Signed-off-by: NRana Shahout <ranas@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Query all supported types of dev caps on driver load.
- Store the Cap data outbox per cap type into driver private data.
- Introduce new Macros to access/dump stored caps (using the auto
  generated data types).
- Obsolete SW representation of dev caps (no need for SW copy for each
  cap).
- Modify IB driver to use new macros for checking caps.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx5_ifc.h was heavily modified here since it is now generated by a
script from the device specification (PRM rev 0.25). This specification
is backward compatible to existing hardware.

Some structures/fields were added here in order to enable the Ethernet
functionality of the driver.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Preparation for upcoming ethernet driver.
- Move msix array from eq_table struct to priv since its not related to
  eq_table
- Intorduce irq_info struct to hold all irq information
- Move name from mlx5_eq to irq_info struct since it is irq property.
- Set IRQ affinity hints
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NRana Shahout <ranas@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As David Daney pointed in mlx4_core driver [1], mlx5_core is also
misusing the DMA-API.

This patch is removing the code that vmap() memory allocated by
dma_alloc_coherent().

After this patch, users of this drivers might fail allocating resources
on memory fragmeneted systems.  This will be fixed later on.

[1] - https://patchwork.ozlabs.org/patch/458531/

CC: David Daney <david.daney@cavium.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-05-28

This series contains updates to ethtool, ixgbe, i40e and i40evf.

John adds helper routines for ethtool to pass VF to rx_flow_spec.  Since
the ring_cookie is 64 bits wide which is much larger than what could be
used for actual queue index values, provide helper routines to pack a VF
index into the cookie.  Then John provides a ixgbe patch to allow flow
director to use the entire queue space.

Neerav provides a i40e patch to collect XOFF Rx stats, where it was not
being collected before.

Anjali provides ATR support for tunneled packets, as well as stats to
count tunnel ATR hits.  Cleaned up PF struct members which are
unnecessary, since we can use the stat index macro directly.  Cleaned
up flow director ATR/SB messages to a higher debug level since they
are not useful unless silicon validation is happening.

Greg provides a patch to disable offline diagnostics if VFs are enabled
since ethtool offline diagnostic tests are not designed (out of scope)
to disable VF functions for testing and re-enable afterward.  Also cleans
up TODO comment that is no longer needed.

Vasu provides a fix an FCoE EOF case where i40e_fcoe_ctxt_eof() maybe
called before i40e_fcoe_eof_is_supported() is called.

Jesse adds skb->xmit_more support for i40evf.  Then provides a performance
enhancement for i40evf by inlining some functions which provides a 15%
gain in small packet performance.  Also cleans up the use of time_stamp
since it is no longer used to determine if there is a tx_hang and was
a part of a previous tx_hang design which is no longer used.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As sock refcnt is taken when sock timer is started in
sk_reset_timer(), the sock refcnt should be put when sock timer
to be deleted is in pending state no matter what "probing_state"
value of tipc sock is.
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes "vlaue" for "value" in include/linux/if_vlan.h.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

classic BPF already exposes skb->dev->ifindex via SKF_AD_IFINDEX extension.
Allow eBPF program to access it as well. Note that classic aborts execution
of the program if 'skb->dev == NULL' (which is inconvenient for program
writers), whereas eBPF returns zero in such case.
Also expose the 'skb_iif' field, since programs triggered by redirected
packet need to known the original interface index.
Summary:
__skb->ifindex         -> skb->dev->ifindex
__skb->ingress_ifindex -> skb->skb_iif
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current algorithm for deciding on the number of VRSS channels is
not optimal since we open up the min of number of CPUs online and the
number of VRSS channels the host is offering. So on a 32 VCPU guest
we could potentially open 32 VRSS subchannels. Experimentation has
shown that it is best to limit the number of VRSS channels to the number
of CPUs within a NUMA node.

Here is the new algorithm for deciding on the number of sub-channels we
would open up:
        1) Pick the minimum of what the host is offering and what the driver
           in the guest is specifying as the default value.
        2) Pick the minimum of (1) and the numbers of CPUs in the NUMA
           node the primary channel is bound to.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is similar to b1cb59cf(net: sysctl_net_core: check SNDBUF
and RCVBUF for min length). I don't think too small values can cause
crashes in the case of udp and tcp, but I've seen this set to too
small values which triggered awful performance. It also makes the
setting consistent across all the wmem/rmem sysctls.
Signed-off-by: NSorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mathieu Olivari says:

====================
Add support for QCA IPQ806x Ethernet GMAC controller

This patch set adds support for the integrated Ethernet GMAC controller
on QCA IPQ806x SoC. This controller is based on a Gigabit Synopsys
DesignWare IP, already supported in the stmmac driver located in
drivers/net/ethernet/stmicro/stmmac.

This change is done as a follow-up to the following thread:
*http://www.spinics.net/lists/netdev/msg311265.html
While previous attempt was creating a new driver to drive this controller,
this new post leverages the existing stmmac driver by implementing the
SoC specific glue to it.

Aside from the pure stmmac glue layer, we have a couple of related
patches:
*IPQ806x NSS clock addition is cherry-picked and refreshed from the
 following thread: https://lkml.org/lkml/2014/8/6/390
*phy-handle and fixed-link support are also added in this change set so the
 driver can be fully functional on platforms using device-trees as well as
 ethernet switches.

V2:
 *Fix MODULE_LICENSE to "Dual BSD/GPL" as the dwmac-ipq806x.c is using
  ISC license.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the device tree bindings documentation for the QCA IPQ806x
variant of the Synopsys DesignWare MAC.
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethernet controller available in IPQ806x is a Synopsys DesignWare
Gigabit MAC IP core, already supported by the stmmac driver.

This glue layer implements some platform specific settings required to
get the controller working on an IPQ806x based platform.
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case DT is used, this change adds the ability to the stmmac driver to
detect a fixed-link PHY, instanciate it, and use it during
phy_connect().

Fixed link PHYs DT usage is described in:
Documentation/devicetree/bindings/net/fixed-link.txt
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On stmmac driver, PHY specification in device-tree was done using the
non-standard property "snps,phy-addr". Specifying a PHY on a different
MDIO bus that the one within the stmmac controller doesn't seem to be
possible when device-tree is used.

This change adds support for the phy-handle property, as specified in
Documentation/devicetree/bindings/net/ethernet.txt.
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the NSS/GMAC clocks and the TCM clock and NSS resets.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>