- 28 8月, 2012 1 次提交
-
-
由 Fabio Estevam 提交于
mx28evk has a free slot (J89) which can be used to populate an SPI NOR Flash. Add support for it. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 23 8月, 2012 1 次提交
-
-
由 Fabio Estevam 提交于
hog_pins is used to setup the pin functions, and it is not neccesarily used only for GPIO pins, so use only 'hog' to describe a more generic term. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 12 7月, 2012 1 次提交
-
-
由 Richard Zhao 提交于
- add usb phy devices - add usb controller devices - add usb vbus regulators Signed-off-by: NRichard Zhao <richard.zhao@freescale.com> Tested-by: NSubodh Nijsure <snijsure@grid-net.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 11 7月, 2012 2 次提交
-
-
由 Shawn Guo 提交于
The presence and muxing of lcdif control pins can vary much on different boards. Move them into imx28-evk.dts to make lcdif_24bit_pins_a only about data pins, so that it can be reused by other boards. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards. Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a more general, and can be used by other boards. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 06 7月, 2012 1 次提交
-
-
由 Shawn Guo 提交于
Add flexan devices for imx28-evk board. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 03 7月, 2012 8 次提交
-
-
由 Shawn Guo 提交于
Add lcd support for imx23-evk and imx28-evk. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Add pwm device and pwm-backlight for imx23-evk and imx28-evk. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Add heartbeat gpio-leds for imx28-evk board. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Add missing properties for fec, phy-supply, phy-reset-gpios and phy-reset-duration, which are required by fec driver for successfully probe fec from device tree, if bootloader hasn't set those things up. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Add vmmc-supply for mmc device, so that the power to mmc slot can be turned on by mmc driver if bootloader hasn't done it. Also remove "okay" status for mmc1/ssp1, as the device has pin conflict with gpmi-nand. Actually the device is already disabled since the mxs-mmc driver adopts pinctrl support because there is no pinctrl setup for the device in dts. Make this explicit by removing "okay" status. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Before gpio_request can directly ask pinctrl system to configure the requested pin into gpio mode, we use "hog" entry (pinctrl state of pin controller itself) to configure gpios. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
Add auart0 and auart3 support. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Reviewed-by: NMarek Vasut <marex@denx.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Huang Shijie 提交于
add gpmi-nand device tree support. add gpmi-nand pinctrl support. Also enable the gpmi support for mx28-evk board. Signed-off-by: NHuang Shijie <b32955@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 13 5月, 2012 3 次提交
-
-
由 Shawn Guo 提交于
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 12 5月, 2012 1 次提交
-
-
由 Dong Aisheng 提交于
This patch includes basic dt support which can boot via nfs rootfs. Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org> Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Acked-by: NMarek Vasut <marex@denx.de>
-