These early versions are no longer supported.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ref_count is currently initialized on start_fw(). This causes
some issues in restart flow, as currently active references
(e.g. unclaimed command) will get cleared, resulting in
invalid reference accounting.

Move the ref_count initialization to the configure() trans op,
so it won't be re-initialized on restart.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware has a race in the flow that indicates the
completion of the authentication. Checking the completion
of the authentication is not really needed anyway since
we can wait for the ALIVE notification instead.
Remove the unneeded and buggy code.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows the op_mode to let the transport know that a
queue is currently frozen and that its timer should be
stopped.
When the queue is unfrozen, its timer should be set to
expire after the remainder of the timeout has elapsed.
This can be used when stations go to sleep. When a station
goes to sleep, the op_mode can freeze the timer so that the
queue will never be considered as stuck. When the station
wakes up, the queue will be unfrozen.
This is meant to avoid false positives that would happen if
a buggy station goes to sleep for a very long time. In case
we have a dedicated queue for this station (BA agreement)
and it goes to sleep for a very long time, the queue would
rightfully be stopped during all that time. In this case,
the stuck queue timer could fire and that would be a false
positive.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.

Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This adds BT Coex data to the prph register list.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In-order to recognize newer step of the device, the driver
must read the chip_version_id from the AUX bus MISC address
space. This will determine what firmware file will be
loaded.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to use the firmware debugging system even when
the configuration values are set hard coded in the firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Different queue can have different behavior. While it can be
unacceptable for a certain queue to be stuck for 2 seconds
(e.g. the command queue), it can happen that another queue
will stay stuck for even longer (a queue servicing a power
saving client in GO).
The op_mode can even make the timeout be a function of the
listen interval.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some devices have 31 TFD queues. Don't enable it yet since
there are still issues with it, but at least prepare the
code for it. There was a bug in the read pointer assignment,
fix that. Also, move the inline functions to iwl-scd.h which
is the right place.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver loads the 2 CPU sections, then it needs to let
the firmware know to start the authentication of the
sections. This is done by writing the relevants bits to
FH_UCODE_LOAD_STATUS.

For CPU1, the driver sets the lower 16 bits. For both CPUs,
the driver sets all the 32 bits.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

C step functionality in the driver is exactly the same as
B step besides the ucode name that present as iwlwifi-8000C-xx.ucode
instead of iwlwifi-8000B-xx.ucode
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The ref_lock that was recently added is missing initialization
which makes lockdep unhappy and is generally a bad idea.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to config the FW and to allocate monitor buffer driver should
run the function iwl_pcie_apply_destination immediately after FW sections
are loaded.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enter d0i3 on suspend, and exit d0i3. Wait for the
command responses in both cases.

Use this mode in case of pcie trans.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement the ref/unref trans ops and track both tx and
host command queues (and hold references while they
are not empty).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the driver is unload, the Manageability Engine should
know about that - send an event to inform it about this
event.
Reviewed-by: NReuven Borok <reuven.borok@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New FW has chunks that are larger than the size limit of the
FH's DMA. To make sure we don't crash it - actively limit the
max size of each chunk.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we reset the device, the CSR_INT gets cleared as well
as CSR_INT_MASK. Meaning that we shouldn't get any interrupt
but, due to a hardware bug, recent devices will keep sending
interrupts. This leads to an interrupt storm while stopping
the device.
The way to fix this is to ACK all the interrupts after the
device is reset so that the value of CSR_INT will stay
0xffffffff.

Fixes: 522713c8 ("iwlwifi: pcie: properly reset the device")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Until this patch, dumping the monitor data could be done only
for PCIe external (DRAM) mode in 7000 HW family. This patch
allows to pull the monitor data also on other families, and
also to pull the monitor data if an internal buffer is used.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Adds all FH registers between FH_MEM_UPPER_BOUND and
FH_MEM_LOWER_BOUND (which should be readable to the driver)
to the dump data when it is collected.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The ucode load flow changed for B0 hardware step.
Change the code accordingly.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Not doing so would allow other possible users of the device
to take ownership and prevent normal WiFi operation.

This fixes the second part of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191Reviewed-by: NMoshe Harel <moshe.harel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Toggle the LMPM_CHICK register when writing chunks into the FW's extended
SRAM. This tells the FW to put the chunk into a different memory space.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We were toggling the wrong bit when we reset the device,
fix that. Moreover, since the reset can take time, we need
to wait before we set the rfkill interrupt. Not doing so
can be racy since the driver is enabling the rfkill
interrupt while the device is resetting which will clear
all the registers including the CSR_INT_MASK.
This can basically lead to a situation where we don't
enable the rfkill interrupt. If that happens, the user will
not be able to re-enable the device when de-asserting
rfkill.

This scenario happened to the submitter of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is fully backward compatible with older platforms.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some rare cases, the firmware can put the device to
sleep after the driver requested the access. This is
because the access request can take a short time to be
propagated to the firmware.

If that happens, the driver may think that it has access
since the firmware hasn't put the device to sleep yet, but
right after the driver's check, the firmware might put the
device to sleep.

Warn when this happens by allowing the firmware to finish
the "put the device sleep" flow so that the driver will
not get access to the device. This will make the issue
visible.

This still doesn't fix the race, but at least it makes
it more visible.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.

Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2c ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.

Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.

This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231

CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwlwifi features a debug mechanism that allows to dump
binary data which is helpful to debug the firmware.
Until now, this data was made available for the userspace
through debugfs. For this exact purpose, devcoredump was
created. Move to the new infrastructure.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the new format the "CSS section" has the same TLV type
as the "mem section". So we need to run the secured flow
for all the 8000 products.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the ARC is reset when we exit from Sx in case we had
WoWLAN running, we can't access the prph before we reset
the NIC.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise we have no way to know that the buffer hasn't been
allocated.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.

Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.

Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Align the trans->hw_rev variable format with previous series
format.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Rather than ANDing with a mask - use existing macros, which
are more readable.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This configuration is not needed for dvm, and it actually
broke it.
Reported-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>