- 20 2月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Replace the accessor to pin defaults with the common code for caching. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 12 2月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Detect multiple digital-out pins in snd_hda_parse_pin_defconfig(). The dig_out_pin and dig_out_type fields become arrays. The codec parser still doesn't use this multiple pins detection, though. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 18 12月, 2008 1 次提交
-
-
由 Takashi Iwai 提交于
Remove codec vendor names from the codec name strings. The vendor name is already given from the vendor name table, so displayed doubly. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 27 11月, 2008 1 次提交
-
-
由 Takashi Iwai 提交于
Split the monolithc HD-audio driver into several pieces: - snd-hda-intel HD-audio PCI controller driver; loaded via udev - snd-hda-codec HD-audio codec bus driver - snd-hda-codec-* Specific HD-audio codec drivers When built as modules, snd-hda-codec (that is invoked by snd-hda-intel) looks up the codec vendor ID and loads the corresponding codec module automatically via request_module(). When built in a kernel, each codec drivers are statically hooked up before probing the PCI. This patch adds appropriate EXPORT_SYMBOL_GPL()'s and the module information for each driver, and driver-linking codes between codec-bus and codec drivers. TODO: - Avoid EXPORT_SYMBOL*() when built-in kernel - Restore __devinit appropriately depending on the condition Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 18 11月, 2008 1 次提交
-
-
由 Wu Fengguang 提交于
Remove get_amp_nid(): it duplicates the one defined in hda_local.h Signed-off-by: NWu Fengguang <wfg@linux.intel.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 13 10月, 2008 1 次提交
-
-
由 Takashi Iwai 提交于
Use generic array helpers to simplify array handling in snd-hda-intel. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 23 9月, 2008 3 次提交
-
-
由 Harald Welte 提交于
VT1708S' Mic Boost should be hidden in hardware design according to some customers' requirements. However, in case of bugs, it has to be exhibited to normal users, so we need to: * open a software backdoor, which is disabled by default in hardware * re-write .tlv & .info, to indicate the actual necessary info, which we cannot get from amplifier's capabiliies Signed-off-by: NLogan Li <LoganLi@viatech.com.cn> Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
As it seems, the recently-sent patch for the 2nd S/PDIF (HDMI) output is not working with alsa-kernel 1.0.18rc3. This patch makes it work by * activating the second S/PDIF output pin in the pin config * consolidating the dig_playback_pcm_prepare() with extra_dig_pcm_prepare() functions * remove the need for an extra hda_pcm_stream structure and rather represents the second digital output as substream within the primary S/PDIF digital out stream. Signed-off-by: NLogan Li <LoganLi@viatech.com.cn> Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
Don't enumerate via_hp_mixer while hp_mux is null (headphone does not exist), to fix the crash of via_independent_hp_info (via_hp_mixer's .info), which will reference hp_mux. Signed-off-by: NLogan Li <LoganLi@viatech.com.cn> Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
- 10 9月, 2008 7 次提交
-
-
由 Harald Welte 提交于
The VT1702 and VT1708S have a second S/PDIF output which is used to connect to a HDMI transmitter. This patch adds support for it. Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
This mode allows an output stream to have two substreams, one for the speakers and one for the headphone. Each of the substreams has independent PCM data and uses a different DAC. Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
The VT1702 and VT1708S codecs are new HDA codecs by VIA. This patch adds support for them to the patch_via.c file for HDA Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
In the current driver, there is a consistent mistake between the SURROUND and the SIDE channels. This patch fixes it. Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Harald Welte 提交于
* add extra parenthesis to make code more readable * use kzalloc() for alloc+zero rather than kcalloc() * ensure that AUTO_SEQ_* starts at 0 Signed-off-by: NHarald Welte <HaraldWelte@viatech.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
- 25 5月, 2008 1 次提交
-
-
由 Takashi Iwai 提交于
We get quite noisy output on the right channel on VT1708 codec when 24bit samples are used. Suppress the 24bit support until any real fix is found. https://bugzilla.novell.com/show_bug.cgi?id=390473Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 24 4月, 2008 4 次提交
-
-
由 Takashi Iwai 提交于
Keep the format verb at closing PCM streams. Introduced snd_hda_codec_cleanup_stream() for the parcicular purpose. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Harvey Harrison 提交于
Move the array declaration to hda_codec.c where it is used and add includes where the individual presets are declared. Fixes the following sparse warnings: sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static? sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static? sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static? sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static? sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static? sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static? sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static? sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static? Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Added a new mixer switch to enable/disable the sharing of the default PCM stream with analog and SPDIF outputs. When "IEC958 Default PCM" switch is on, the PCM stream is routed both to analog and SPDIF outputs. This is the behavior in the earlier version. Turning this switch off has a merit for some codecs, though. Some codec chips don't support 24bit formats for SPDIF but only for analog outputs. In this case, you can use 24bit format by disabling this switch. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
In the current scheme, PCM device numbers are assigned incrementally in the order of codecs. This causes problems when the codec number is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then the HDMI becomes the first PCM, which is picked up as the default output device. Unfortuantely this doesn't work well with normal setups. This patch introduced the fixed device numbers for the PCM types, namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned according to the corresponding PCM type. After this patch, HDMI will be always assigned to PCM #3, SPDIF to PCM #1, and the first analog to PCM #0, etc. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 01 2月, 2008 4 次提交
-
-
由 Takashi Iwai 提交于
Enable the SPDIF input-pin on VIA codecs when SPDIF-input is enabled by BIOS. Also, including a bit code clean up. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Takashi Iwai 提交于
Removed 'FIXME' comments that have been already fixed. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Takashi Iwai 提交于
This header file exists only for some hacks to adapt alsa-driver tree. It's useless for building in the kernel. Let's move a few lines in it to sound/core.h and remove it. With this patch, sound/driver.h isn't removed but has just a single compile warning to include it. This should be really killed in future. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Josepch Chan 提交于
This patch adds support for VIA new HD audio codec, VT1708B. Signed-off-by: NJosepch Chan <josephchan@via.com.tw> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
- 23 10月, 2007 1 次提交
-
-
由 Takashi Iwai 提交于
dac_nids arrays in each codec support code may have up to 5 items when assigned from the auto-configurator. Some codec codes have less numbers than the possible max. This patch defines the constant and fixes the array definitions. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
- 16 10月, 2007 2 次提交
-
-
由 Takashi Iwai 提交于
Added CONFIG_SND_HDA_POWER_SAVE kconfig. It's an experimental option to achieve an aggressive power-saving. With this option, the driver will turn on/off the power of each codec and controller chip dynamically on demand. The patch introduces a new module option 'power_save'. It specifies the second of time-out for automatic power-down. As default, it's 10 seconds. Setting 0 means to suppress the power-saving feature. The codec may have analog-input loopbacks, which are usually represented by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'. When these are on, we cannot turn off the mixer and the codec chip has to be kept on. For bookkeeping these states, a new codec-callback is introduced. For the bus-controller side, a new callback pm_notify is introduced, which can be used to turn on/off the contoller appropriately. Note that this power-saving might cause slight click-noise at power-on/off. Also, it might take some time to wake up the codec, and might even drop some tones at the very beginning. This seems to be the side-effect of turning off the controller chip. This turn-off of the controller can be disabled by undefining HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
So far, the driver looked the table of snd_kcontrol_new used for creating mixer elements and forces to call each of its put callbacks in PM resume code. This is too ugly and hackish. Now, the resume is simplified using the codec amp and command register caches. The driver simply restores the values that have been written in the cache table. With this simplification, most codec support codes don't require any special resume callback. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 11 5月, 2007 1 次提交
-
-
由 Takashi Iwai 提交于
Fix SPDIF output (at least on Realtek codecs). The DIGI_CONVERT verbs have to be reset before the PCM stream is set up. Otherwise the digital setup is screwed up. Also, check the AMP capability before setting AMP of the digital out widget. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 03 5月, 2007 1 次提交
-
-
由 Jean Delvare 提交于
I noticed that many source files include <linux/pci.h> while they do not appear to need it. Here is an attempt to clean it all up. In order to find all possibly affected files, I searched for all files including <linux/pci.h> but without any other occurence of "pci" or "PCI". I removed the include statement from all of these, then I compiled an allmodconfig kernel on both i386 and x86_64 and fixed the false positives manually. My tests covered 66% of the affected files, so there could be false positives remaining. Untested files are: arch/alpha/kernel/err_common.c arch/alpha/kernel/err_ev6.c arch/alpha/kernel/err_ev7.c arch/ia64/sn/kernel/huberror.c arch/ia64/sn/kernel/xpnet.c arch/m68knommu/kernel/dma.c arch/mips/lib/iomap.c arch/powerpc/platforms/pseries/ras.c arch/ppc/8260_io/enet.c arch/ppc/8260_io/fcc_enet.c arch/ppc/8xx_io/enet.c arch/ppc/syslib/ppc4xx_sgdma.c arch/sh64/mach-cayman/iomap.c arch/xtensa/kernel/xtensa_ksyms.c arch/xtensa/platform-iss/setup.c drivers/i2c/busses/i2c-at91.c drivers/i2c/busses/i2c-mpc.c drivers/media/video/saa711x.c drivers/misc/hdpuftrs/hdpu_cpustate.c drivers/misc/hdpuftrs/hdpu_nexus.c drivers/net/au1000_eth.c drivers/net/fec_8xx/fec_main.c drivers/net/fec_8xx/fec_mii.c drivers/net/fs_enet/fs_enet-main.c drivers/net/fs_enet/mac-fcc.c drivers/net/fs_enet/mac-fec.c drivers/net/fs_enet/mac-scc.c drivers/net/fs_enet/mii-bitbang.c drivers/net/fs_enet/mii-fec.c drivers/net/ibm_emac/ibm_emac_core.c drivers/net/lasi_82596.c drivers/parisc/hppb.c drivers/sbus/sbus.c drivers/video/g364fb.c drivers/video/platinumfb.c drivers/video/stifb.c drivers/video/valkyriefb.c include/asm-arm/arch-ixp4xx/dma.h sound/oss/au1550_ac97.c I would welcome test reports for these files. I am fine with removing the untested files from the patch if the general opinion is that these changes aren't safe. The tested part would still be nice to have. Note that this patch depends on another header fixup patch I submitted to LKML yesterday: [PATCH] scatterlist.h needs types.h http://lkml.org/lkml/2007/3/01/141Signed-off-by: NJean Delvare <khali@linux-fr.org> Cc: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 09 2月, 2007 1 次提交
-
-
由 Joseph Chan 提交于
This patch is VIA first release for HD audio codec, VT1708(A) and it provides geneneral HD audio driver features. Signed-off-by: NJoseph Chan <josephchan@via.com.tw> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-