* dcache-cleanup:
  vfs: get rid of insane dentry hashing rules

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: ahci_start_engine compliant to AHCI spec
  ata: pata_at91.c bugfix for initial_timing initialisation
  ata: pata_at91.c bugfix for high master clock
  ahci: AHCI-mode SATA patch for Intel Panther Point DeviceIDs
  ata_piix: IDE-mode SATA patch for Intel Panther Point DeviceIDs
  libata: Pioneer DVR-216D can't do SETXFER
  ahci: don't enable port irq before handler is registered
  libata: Implement ATA_FLAG_NO_DIPM and apply it to mcp65
  libata: Kill unused ATA_DFLAG_{H|D}IPM flags
  ahci: EM supported message type sysfs attribute

* 'for-linus' of git://git.infradead.org/ubifs-2.6:
  UBIFS: fix master node recovery
  UBIFS: fix false assertion warning in case of I/O failures
  UBIFS: fix false space checking failure

At the end of section 10.1 of AHCI spec (rev 1.3), it states

Software shall not set PxCMD.ST to 1 until it is determined that
a functoinal device is present on the port as determined by
PxTFD.STS.BSY=0, PxTFD.STS.DRQ=0 and PxSSTS.DET=3h

Even though most AHCI host controller works without this check,
specific controller will fail under this condition.
Signed-off-by: NJian Peng <jipeng2005@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The "struct ata_timing" must contain 10 members, but ".dmack_hold" member was
forgotten for "initial_timing" initialisation. This patch fixes such a problem.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The AT91SAM9 microcontrollers with master clock higher then 105 MHz
and PIO0, have overflow of the NCS_RD_PULSE value in the MSB. This
lead to "NCS_RD_PULSE" pulse longer then "NRD_CYCLE" pulse and driver
does not detect ATA device.
Signed-off-by: NIgor Plyatov <plyatov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The previously submitted patch was word-wrapped.

This patch adds the AHCI-mode SATA DeviceIDs for the Intel Panther Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The previously submitted patch was word-wrapped.

This patch adds the IDE-mode SATA DeviceIDs for the Intel Panther
Point PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

 Commit 4a5610a0 fixed an issue with
 the Pioneer DVR-212D not handling SETXFER correctly. An openSUSE user
 reported a similar issue with his DVR-216D that the NOSETXFER horkage
 worked around for him as well.

 This patch adds the DVR-216D (1.08) to the horkage list for NOSETXFER.

 The issue was reported at:
 https://bugzilla.novell.com/show_bug.cgi?id=679143Reported-by: NVolodymyr Kyrychenko <vladimir.kirichenko@gmail.com>
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The ahci_pmp_attach() & ahci_pmp_detach() unmask port irqs, but they
are also called during port initialization, before ahci host irq
handler is registered. On ce4100 platform, this sometimes triggers
"irq 4: nobody cared" message when loading driver.

Fixed this by not touching the register if the port is in frozen
state, and mark all uninitialized port as frozen.
Signed-off-by: NMaxime Bizon <mbizon@freebox.fr>
Acked-by: NTejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

NVIDIA mcp65 familiy of controllers cause command timeouts when DIPM
is used.  Implement ATA_FLAG_NO_DIPM and apply it.

This problem was reported by Stefan Bader in the following thread.

 http://thread.gmane.org/gmane.linux.ide/48841

stable: applicable to 2.6.37 and 38.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NStefan Bader <stefan.bader@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

ATA_DFLAG_{H|D}IPM flags are no longer used.  Kill them.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds an sysfs attribute 'em_message_supported' to the
ahci host device which prints out the supported enclosure management
message types.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Commit 40aee729 ('kconfig: fix default value for choice input')
fixed some cases where kconfig would select the wrong option from a
choice with a single valid option and thus enter an infinite loop.

However, this broke the test for user input of the form 'N?', because
when kconfig selects the single valid option the input is zero-length
and the test will read the byte before the input buffer.  If this
happens to contain '?' (as it will in a mips build on Debian unstable
today) then kconfig again enters an infinite loop.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [2.6.17+]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The dentry hashing rules have been really quite complicated for a long
while, in odd ways.  That made functions like __d_drop() very fragile
and non-obvious.

In particular, whether a dentry was hashed or not was indicated with an
explicit DCACHE_UNHASHED bit.  That's despite the fact that the hash
abstraction that the dentries use actually have a 'is this entry hashed
or not' model (which is a simple test of the 'pprev' pointer).

The reason that was done is because we used the normal 'is this entry
unhashed' model to mark whether the dentry had _ever_ been hashed in the
dentry hash tables, and that logic goes back many years (commit
b3423415: "dcache: avoid RCU for never-hashed dentries").

That, in turn, meant that __d_drop had totally different unhashing logic
for the dentry hash table case and for the anonymous dcache case,
because in order to use the "is this dentry hashed" logic as a flag for
whether it had ever been on the RCU hash table, we had to unhash such a
dentry differently so that we'd never think that it wasn't 'unhashed'
and wouldn't be free'd correctly.

That's just insane.  It made the logic really hard to follow, when there
were two different kinds of "unhashed" states, and one of them (the one
that used "list_bl_unhashed()") really had nothing at all to do with
being unhashed per se, but with a very subtle lifetime rule instead.

So turn all of it around, and make it logical.

Instead of having a DENTRY_UNHASHED bit in d_flags to indicate whether
the dentry is on the hash chains or not, use the hash chain unhashed
logic for that.  Suddenly "d_unhashed()" just uses "list_bl_unhashed()",
and everything makes sense.

And for the lifetime rule, just use an explicit DENTRY_RCUACCEES bit.
If we ever insert the dentry into the dentry hash table so that it is
visible to RCU lookup, we mark it DENTRY_RCUACCESS to show that it now
needs the RCU lifetime rules.  Now suddently that test at dentry free
time makes sense too.

And because unhashing now is sane and doesn't depend on where the dentry
got unhashed from (because the dentry hash chain details doesn't have
some subtle side effects), we can re-unify the __d_drop() logic and use
common code for the unhashing.

Also fix one more open-coded hash chain bit_spin_lock() that I missed in
the previous chain locking cleanup commit.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM: Add missing syscore_suspend() and syscore_resume() calls
  PM: Fix error code paths executed after failing syscore_suspend()

It's a useless abstraction for 'hlist_bl_head', and it doesn't actually
help anything - quite the reverse.  All the users end up having to know
about the hlist_bl_head details anyway, using 'struct hlist_bl_node *'
etc. So it just makes the code look confusing.

And the cost of it is extra '&b->head' syntactic noise, but more
importantly it spuriously makes the hash table dentry list look
different from the per-superblock DCACHE_DISCONNECTED dentry list.

As a result, the code ended up using ad-hoc locking for one case and
special helper functions for what is really another totally identical
case in the very same function.

Make it all look and work the same.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty/n_gsm: fix bug in CRC calculation for gsm1 mode
  serial/imx: read cts state only after acking cts change irq
  parport_pc.c: correctly release the requested region for the IT887x

Right now all RCU walks fall back to reference walk when CONFIG_SECURITY
is enabled, even though just the standard capability module is active.
This is because security_inode_exec_permission unconditionally fails
RCU walks.

Move this decision to the low level security module. This requires
passing the RCU flags down the security hook. This way at least
the capability module and a few easy cases in selinux/smack work
with RCU walks with CONFIG_SECURITY=y
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix unused warnings when !SND_HDA_NEEDS_RESUME
  ALSA: hda - Add a fix-up for Acer dmic with ALC271x codec
  ASoC: add a module alias to the FSI driver
  ALSA: emu10k1 - Fix "Music" controls to "Synth" controls in documents
  ARM: s3c2440: gta02; Register dfbmcs320 device for BT audio interface
  ASoC: codecs: JZ4740: Fix OOPS
  ASoC: Fix output PGA enabling in wm_hubs CODECs
  ASoC: sn95031: decorate function with __devexit_p()
  ASoC: SAMSUNG: Fix the inverted clocks handling for pcm driver
  ASoC: sst_platform: Fix lock acquring
  ASoC: fsi: driver safely remove for against irq
  ASoC: fsi: modify vague PM control on probe
  ASoC: fsi: take care in failing case of dai register
  MAINTAINERS: Update Samsung ASoC maintainer's id
  ASoC: WM8903: HP and Line out PGA/mixer DAPM fixes
  ASoC: Set left channel volume update bits for WM8994
  ASoC: fix config error path
  ASoC: check channel mismatch between cpu_dai and codec_dai
  ASoC: Tegra: Suspend/resume support

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf, x86: Update/fix Intel Nehalem cache events
  perf, x86: P4 PMU - Don't forget to clear cpuc->active_mask on overflow
  x86, perf event: Turn off unstructured raw event access to offcore registers
  perf: Support Xeon E7's via the Westmere PMU driver

Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  xtensa: Fixup irq conversion fallout and nmi_count

Change the Nehalem cache events to use retired memory instruction counters
(similar to Westmere), this greatly improves the provided stats.

Using:

main ()
{
        int i;

        for (i = 0; i < 1000000000; i++) {
                asm("mov (%%rsp), %%rbx;"
                    "mov %%rbx, (%%rsp);" : : : "rbx");
        }
}

We find:

 $ perf stat --repeat 10 -e instructions:u -e l1-dcache-loads:u -e l1-dcache-stores:u ./loop_1b_loads+stores
  Performance counter stats for './loop_1b_loads+stores' (10 runs):
      4,000,081,056 instructions:u           #      0.000 IPC ( +-   0.000% )
      4,999,502,846 l1-dcache-loads:u          ( +-   0.008% )
      1,000,034,832 l1-dcache-stores:u         ( +-   0.000% )
         1.565184942  seconds time elapsed   ( +-   0.005% )

The 5b is surprising - we'd expect 1b:

 $ perf stat --repeat 10 -e instructions:u -e r10b:u -e l1-dcache-stores:u ./loop_1b_loads+stores
  Performance counter stats for './loop_1b_loads+stores' (10 runs):
      4,000,081,054 instructions:u           #      0.000 IPC ( +-   0.000% )
      1,000,021,961 r10b:u                     ( +-   0.000% )
      1,000,030,951 l1-dcache-stores:u         ( +-   0.000% )
         1.565055422  seconds time elapsed   ( +-   0.003% )

Which this patch thus fixes.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/n/tip-q9rtru7b7840tws75xzboapv@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

It's not enough to simply disable event on overflow the
cpuc->active_mask should be cleared as well otherwise counter
may stall in "active" even in real being already disabled (which
potentially may lead to the situation that user may not use this
counter further).

Don pointed out that:

 " I also noticed this patch fixed some unknown NMIs
   on a P4 when I stressed the box".
Tested-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NCyrill Gorcunov <gorcunov@openvz.org>
Acked-by: NDon Zickus <dzickus@redhat.com>
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303398203-2918-3-git-send-email-dzickus@redhat.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Andi Kleen pointed out that the Intel offcore support patches were merged
without user-space tool support to the functionality:

 |
 | The offcore_msr perf kernel code was merged into 2.6.39-rc*, but the
 | user space bits were not. This made it impossible to set the extra mask
 | and actually do the OFFCORE profiling
 |

Andi submitted a preliminary patch for user-space support, as an
extension to perf's raw event syntax:

 |
 | Some raw events -- like the Intel OFFCORE events -- support additional
 | parameters. These can be appended after a ':'.
 |
 | For example on a multi socket Intel Nehalem:
 |
 |    perf stat -e r1b7:20ff -a sleep 1
 |
 | Profile the OFFCORE_RESPONSE.ANY_REQUEST with event mask REMOTE_DRAM_0
 | that measures any access to DRAM on another socket.
 |

But this kind of usability is absolutely unacceptable - users should not
be expected to type in magic, CPU and model specific incantations to get
access to useful hardware functionality.

The proper solution is to expose useful offcore functionality via
generalized events - that way users do not have to care which specific
CPU model they are using, they can use the conceptual event and not some
model specific quirky hexa number.

We already have such generalization in place for CPU cache events,
and it's all very extensible.

"Offcore" events measure general DRAM access patters along various
parameters. They are particularly useful in NUMA systems.

We want to support them via generalized DRAM events: either as the
fourth level of cache (after the last-level cache), or as a separate
generalization category.

That way user-space support would be very obvious, memory access
profiling could be done via self-explanatory commands like:

  perf record -e dram ./myapp
  perf record -e dram-remote ./myapp

... to measure DRAM accesses or more expensive cross-node NUMA DRAM
accesses.

These generalized events would work on all CPUs and architectures that
have comparable PMU features.

( Note, these are just examples: actual implementation could have more
  sophistication and more parameter - as long as they center around
  similarly simple usecases. )

Now we do not want to revert *all* of the current offcore bits, as they
are still somewhat useful for generic last-level-cache events, implemented
in this commit:

  e994d7d2: perf: Fix LLC-* events on Intel Nehalem/Westmere

But we definitely do not yet want to expose the unstructured raw events
to user-space, until better generalization and usability is implemented
for these hardware event features.

( Note: after generalization has been implemented raw offcore events can be
  supported as well: there can always be an odd event that is marginally
  useful but not useful enough to generalize. DRAM profiling is definitely
  *not* such a category so generalization must be done first. )

Furthermore, PERF_TYPE_RAW access to these registers was not intended
to go upstream without proper support - it was a side-effect of the above
e994d7d2 commit, not mentioned in the changelog.

As v2.6.39 is nearing release we go for the simplest approach: disable
the PERF_TYPE_RAW offcore hack for now, before it escapes into a released
kernel and becomes an ABI.

Once proper structure is implemented for these hardware events and users
are offered usable solutions we can revisit this issue.
Reported-by: NAndi Kleen <ak@linux.intel.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302658203-4239-1-git-send-email-andi@firstfloor.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

There's a new model number public, 47, for Xeon E7 (aka Westmere EX).
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: a.p.zijlstra@chello.nl
Link: http://lkml.kernel.org/r/1303429715-10202-1-git-send-email-andi@firstfloor.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  ide: unexport DISK_EVENT_MEDIA_CHANGE for ide-gd and ide-cd
  block: don't propagate unlisted DISK_EVENTs to userland
  elevator: check for ELEVATOR_INSERT_SORT_MERGE in !elvpriv case too

check_events() implementations in both ide-gd and ide-cd are
inadequate for in-kernel event polling.  Both generate media change
events continuously when certain conditions are met causing infinite
event loop between the driver and userland event handler.

As disk event now supports suppression of unlisted events, simply
de-listing DISK_EVENT_MEDIA_CHANGE from disk->events resolves the
problem.  Internal handling around media revalidation will behave the
same while userland will fall back to userland event polling after
detecting the device doesn't support disk events.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NJens Axboe <jaxboe@fusionio.com>
Acked-by: N"David S. Miller" <davem@davemloft.net>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

DISK_EVENT_MEDIA_CHANGE is used for both userland visible event and
internal event for revalidation of removeable devices.  Some legacy
drivers don't implement proper event detection and continuously
generate events under certain circumstances.  For example, ide-cd
generates media changed continuously if there's no media in the drive,
which can lead to infinite loop of events jumping back and forth
between the driver and userland event handler.

This patch updates disk event infrastructure such that it never
propagates events not listed in disk->events to userland.  Those
events are processed the same for internal purposes but uevent
generation is suppressed.

This also ensures that userland only gets events which are advertised
in the @events sysfs node lowering risk of confusion.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

The sort insert is the one that goes to the IO scheduler. With
the SORT_MERGE addition, we could bypass IO scheduler setup
but still ask the IO scheduler to insert the request. This would
cause an oops on switching IO schedulers through the sysfs
interface, unless the disk just happened to be idle while it
occured.
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: fix duplicate message output

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, numa: Fix cpu nodemasks for NUMA emulation and CONFIG_DEBUG_PER_CPU_MAPS
  Revert "x86, NUMA: Fix fakenuma boot failure"

Change <sectors> from unsigned long long to sector_t.
This matches its source field.

  ERROR: "__udivdi3" [drivers/md/raid456.ko] undefined!
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  virtio: console: Enable call to hvc_remove() on console port remove
  virtio_pci: Prevent double-free of pci regions after device hot-unplug
  virtio: Decrement avail idx on buffer detach

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  agp: fix arbitrary kernel memory writes
  agp: fix OOM and buffer overflow
  drm/radeon/kms: fix IH writeback on r6xx+ on big endian machines

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Initialise g4x watermarks for disabled pipes
  drm/i915: Sanitize the output registers after resume
  drm/i915/tv: Fix modeset flickering introduced in 7f58aabc
  drm/i915/tv: Only poll for TV connections
  drm/i915/tv: Remember the detected TV type

* git://git.infradead.org/iommu-2.6:
  intel_iommu: disable all VT-d PMRs when TXT launched
  intel-iommu: Fix get_domain_for_dev() error path
  intel-iommu: Unlink domain from iommu
  intel-iommu: Fix use after release during device attach

For some reason generic_setxattr() did not pass flags (XATTR_CREATE,
XATTR_REPLACE) to the filesystem specific helper. This caused that
setxattr(2) syscall just ignored these flags.

Fix the bug by passing flags correctly.
Signed-off-by: NJan Kara <jack@suse.cz>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This call was disabled as hot-unplugging one virtconsole port led to
another virtconsole port freezing.

Upon testing it again, this now works, so enable it.

In addition, a bug was found in qemu wherein removing a port of one type
caused the guest output from another port to stop working.  I doubt it
was just this bug that caused it (since disabling the hvc_remove() call
did allow other ports to continue working), but since it's all solved
now, we're fine with hot-unplugging of virtconsole ports.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

In the case where a virtio-console port is in use (opened by a program)
and a virtio-console device is removed, the port is kept around but all
the virtio-related state is assumed to be gone.

When the port is finally released (close() called), we call
device_destroy() on the port's device.  This results in the parent
device's structures to be freed as well.  This includes the PCI regions
for the virtio-console PCI device.

Once this is done, however, virtio_pci_release_dev() kicks in, as the
last ref to the virtio device is now gone, and attempts to do

     pci_iounmap(pci_dev, vp_dev->ioaddr);
     pci_release_regions(pci_dev);
     pci_disable_device(pci_dev);

which results in a double-free warning.

Move the code that releases regions, etc., to the virtio_pci_remove()
function, and all that's now left in release_dev is the final freeing of
the vp_dev.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>