Add pinmux configurations for gpio matrix keypad. In this patch, only
single named mode/state is added and these pins are configured during
pinctrl driver initialization.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Samsung's K3PE0E000B memory part is used in OMAP5-evm board.
Adding timings and geometry details for Samsung's memory part and
attaching the same to device-handle of EMIF1/2.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Adding EMIF device tree data for OMAP5 boards.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Memory present for OMAP5-evm is 2GB. But in dts file
it is specified as 1GB. Correcting the same.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add the 32kHz counter node for OMAP5 devices.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add the 11 timer nodes for OMAP5 devices.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

For OMAP4 devices, timers 5-8 have both a L3 bus address and a Cortex-A9
private bus address. Currently the device-tree source only contains the
L3 bus address for these timers. Update these timers to include the
Cortex-A9 private address and make the default address the Cortex-A9
private bus address to match the current HWMOD implementation.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add McSPI data node to AM33XX device tree file. The McSPI module (and so
as the driver) is reused from OMAP4.
Signed-off-by: NPhilip, Avinash <avinashphilip@ti.com>
Tested-by: NMatt Porter <mporter@ti.com>
[b-cousson@ti.com: Remove interrupt-parent]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add am33xx rtc node.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
[b-cousson@ti.com: Update the subject]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Rename the files to have names consistent across OMAP boards.

Update the Makefile to use the new name.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add base address and interrupt line inside Device Tree data for
OMAP5.
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add base address and interrupt line inside Device Tree data for
OMAP5.

Fix as well the wrong compatible string on UART5 & 6.
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Reviewed-by: NShubhrajyoti D <shubhrajyoti@ti.com>
[b-cousson@ti.com: Update the changelog to reflect the fixes
done in the patch]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add base address and interrupt line inside Device Tree data for
OMAP5
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Reviewed-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add base address and interrupt line inside Device Tree data for
OMAP5.
Signed-off-by: NSebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Adds the counter-32k timers nodes present in OMAP2/3/4 devices and
device-tree binding documentation for OMAP counter-32k.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add the 12 GP timers nodes present in OMAP2.
Add the 12 GP timers nodes present in OMAP3.
Add the 11 GP timers nodes present in OMAP4.
Add the 7 GP timers nodes present in AM33xx.

Add documentation for timer properties specific to OMAP.

Thanks to Vaibhav Hiremath for creating the AM33xx timer nodes. I have modified
Vaibhav's original nodes adding information on which timers support a PWM
output.

V5 changes:
- Updated timer register sizes for OMAP2/3/4.
- Modified AM335x timer register size to be 1KB instead of 4KB to align with
  HWMOD.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Acked-Reviewed-&-Tested-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

The interrupt-parent attribute does not have to be added in each
node since the fmwk will check for the parent as well to get it.

Create an interrupt-parent for OMAP2, OMAP3, AM33xx and remove the
attributes from every nodes that were using it.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sebastien Guiriec <s-guiriec@ti.com>

*reg* property for ocp2scp was previously obtained from ti,hwmods property.
But that is now explicitly added to the dt node.
Also updated the documentation with *reg* info.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add twl4030-usb data node in twl4030 device tree file. twl4030-usb is the phy
driver for MUSB used in omap3 chipsets. The dt data is comprised of two
interrupts, one for ID and one for VBUS and three phandles to regulator.
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add twl6030-usb data node in twl6030 device tree file. twl6030-usb is the
comparator driver for USB that detects VBUS and ID events. The dt data is
comprised of two interrupts, one for ID and one for VBUS and a phandle to the
regulator.
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Update i2c trivial-devices list by adding the description for
ti,tmp275 temperature sensor and taos,tsl2550 ambient light
sensor.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add AM335X EVM-SK device tree source (am335x-sk.dts) file to use
the am33xx.dtsi SoC file, along with the memory node information.

Also adds support for tps65910 regulator and lis331dlh accelerometer.
Following drivers/functionality were tested on AM335x-EVM-SK.
* I2C
* TPS65910 regulators
* lis331dlh accelerometer

AM335x EVM Starter Kit details can be accessed from:
http://www.ti.com/tool/tmdssk3358Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.

TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add Bosch D_CAN controller device tree data to AM33XX dtsi
file by adding d_can device nodes with all the necessary
parameters.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Adds basic pinctrl device tree data for AM33XX family of devices.
This patch is based on the pinctrl-single driver.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.

Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.

Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.

This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.

V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
  configuration
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Pull ktest confusion fix from Steven Rostedt:
 "With the v3.7-rc2 kernel, the network cards on my target boxes were
  not being brought up.

  I found that the modules for the network was not being installed.
  This was due to the config CONFIG_MODULES_USE_ELF_RELA that came
  before CONFIG_MODULES, and confused ktest in thinking that
  CONFIG_MODULES=y was not found.

  Ktest needs to test all configs and not just stop if something starts
  with CONFIG_MODULES."

* tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA

Pull minor spi MXS fixes from Mark Brown:
 "These fixes are both pretty minor ones and are driver local."

* tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
  spi: mxs: Terminate DMA in case of DMA timeout
  spi: mxs: Assign message status after transfer finished

Pull arm-soc fixes from Arnd Bergmann:
 "Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.

  These come a little later than I had hoped but unfortunately we had a
  few of these patches cause regressions themselves and had to work out
  how to deal with those in the meantime."

* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  Revert "ARM i.MX25: Fix PWM per clock lookups"
  ARM: versatile: fix versatile_defconfig
  ARM: mvebu: update defconfig with 3.7 changes
  ARM: at91: fix at91x40 build
  ARM: socfpga: Fix socfpga compilation with early_printk() enabled
  ARM: SPEAr: Remove unused empty files
  MAINTAINERS: Add arm-soc tree entry
  ARM: dts: mxs: add the "clock-names" for gpmi-nand
  ARM: ux500: Correct SDI5 address and add some format changes
  ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
  ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
  ARM: at91: drop duplicated config SOC_AT91SAM9 entry
  ARM: at91/i2c: change id to let i2c-at91 work
  ARM: at91/i2c: change id to let i2c-gpio work
  ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
  ARM: at91: fix external interrupt specification in board code
  ARM: at91: fix external interrupts in non-DT case
  ARM: at91: at91sam9g10: fix SOC type detection
  ARM: at91/tc: fix typo in the DT document
  ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
  ...

Functions generic_file_splice_read and generic_file_splice_write access
the pagecache directly. For block devices these functions must be locked
so that block size is not changed while they are in progress.

This patch is an additional fix for commit b87570f5 ("Fix a crash
when block device is read and block size is changed at the same time")
that locked aio_read, aio_write and mmap against block size change.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.

This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.

So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.

This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.

This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.

From: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 92063cee, it
was applied prematurely, causing this build error for
imx_v4_v5_defconfig:

arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in

Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.

This changes at91x40 in the same way that the other platforms
were changed.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>