When two netdev have same link local addresses (such as vlan and non
vlan), two rdma cm listen id should be able to bind to following different
addresses.

listener-1: addr=lla, scope_id=A, port=X
listener-2: addr=lla, scope_id=B, port=X

However while comparing the addresses only addr and port are considered,
due to which 2nd listener fails to listen.

In below example of two listeners, 2nd listener is failing with address in
use error.

$ rping -sv -a fe80::268a:7ff:feb3:d113%ens2f1 -p 4545&

$ rping -sv -a fe80::268a:7ff:feb3:d113%ens2f1.200 -p 4545
rdma_bind_addr: Address already in use

To overcome this, consider the scope_ids as well which forms the accurate
IPv6 link local address.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

IPv6 link local address for a VLAN netdevice has nothing to do with its
resemblance with the default GID, because VLAN link local GID is in
different layer 2 domain.

Now that RoCE MAD packet processing and route resolution consider the
right GID index, there is no need for an unnecessary check which prevents
the addition of vlan based IPv6 link local GIDs.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Switchdev mode and mutiport RoCE mode aren't compatible at this point.
Don't create IB reps when a user switches to switchdev mode and the driver
operates in that mode.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

When working in mutliport RoCE mode it is possible to attach a slave
before the master. In that case the slave is waiting for a master to be
attached.  When the master is attached it goes over the list of waiting
slaves, finds a slave that is compatible and tries to bind it to itself.

The call stack is:
mlx5_ib_init_multiport_master() -> mlx5_ib_bind_slave_port()

In the bind function we will create a netdev notifier, but this is done
before we initialize the RoCE structure (this is done at a later stage by
the master in the ROCE stage).

Once events are delivered to that notifier we will use
mlx5_ib_get_native_port_mdev() to get the actual port and as the native
port is zero we will access an invalid index in the port structure.

Move the RoCE structure initialization to an earlier stage.

Fixes: 32f69e4b ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Remove the limitations that were in place and provide support for DEVX and
raw flow creation on reps.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Add MLX5_OP_QUERY_ESW_VPORT_CONTEXT to devx white list. It will be allowed
only if HCA_CAP.eswitch_manager==1.
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Allow this only via mlx5 raw create flow API, legacy verbs are not
supported. To accommodate that, we add a new attribute to matcher creation
to indicate the type of flow table to be used.
	MLX5_IB_ATTR_FLOW_MATCHER_FT_TYPE
With this new attribute MLX5_IB_ATTR_FLOW_MATCHER_FLOW_FLAGS is no longer
needed, we keep it for compatibility but at most only a single attribute can
be passed of the two.

When inserting a flow rule to the FDB we require that a DEVX FT is
provided as a destination, no other configuration is allowed.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Instead of failing the request, just use the supported number of flow
entries.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Now that we have a specific prio inside the FDB namespace allow retrieving
it from the RDMA side.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Provide an option to change the net namespace of a rdma device through a
netlink command. When multiple rdma devices exists in a system, and when
containers are used, this will limit rdma device visibility to a specified
net namespace.

An example command to change net namespace of mlx5_1 device to the
previously created net namespace 'foo' is:

$ ip netns add foo
$ rdma dev set mlx5_1 netns foo
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Introduce a helper function that changes rdma device's net namespace which
performs mini disable/enable sequence to have device visible only in
assigned net namespace.

Device unregistration, device rename and device change net namespace
may be invoked concurrently.

(a) device unregistration needs to wait if a device change (rename or net
    namespace change) operation is in progress.
(b) device net namespace change should not proceed if the unregistration
    has started.
(c) while one cpu is changing device net namespace, other cpu should not
    be able to rename or change net namespace.

To address above concurrency,
(a) Use unreg_mutex to synchronize between ib_unregister_device() and net
    namespace change operation
(b) In cases where unregister_device() has started unregistration before
    change_netns got chance to acquire unreg_mutex, validate the refcount
    - if it dropped to zero, abort the net namespace change operation.

Finally use the helper function to change net namespace of ib device to
move the device back to init_net when such net is deleted.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

So we can use the disable_device() helper while changing the net namespace
of the rdma device in a subsequent patch, move free_netdevs() out of it.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Fix typo 'faspath' -> 'pastpath'.
Signed-off-by: NChengguang Xu <cgxu519@gmx.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

There is a spelling mistake in a module parameter description. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Currently if alloc_skb fails to allocate the skb a null skb is passed to
t4_set_arp_err_handler and this ends up dereferencing the null skb.  Avoid
the NULL pointer dereference by checking for a NULL skb and returning
early.

Addresses-Coverity: ("Dereference null return")
Fixes: b38a0ad8 ("RDMA/cxgb4: Set arp error handler for PASS_ACCEPT_RPL messages")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NPotnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Currently when the call to create_flow_rule_vport_sq fails, the error
check is being performed on err rather than on the return pointer
flow_rule.  The return flow_rule maybe NULL (which is not considered an
error) or an error code, so check for the error on flow_rule.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: d5ed8ac3 ("RDMA/mlx5: Move default representors SQ steering to rule to modify QP")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Removing the use of IDR variable just to name the function ids. Using the
PCI_FUNC(pdev->devfn) instead to create the device name, associated
resources and to print driver into at various places.
Reported-by: NMatthew Wilcox <willy@infradead.org>
Signed-off-by: NDevesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Now that we have a single IB device with multiple ports we can remove the
VF representor profile.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Move from IB device (representor) per virtual function to single IB device
with port per virtual function (port 1 represents the uplink). As number
of ports is a static property of an IB device, declare the IB device with
as many port as the possible according to the PCI bus.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

We store the SMI information in the core device's struct, make sure we set
that information only once (and not per port), while here make the for
loop based on the actual size of the array.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The design of representors is such that once an IB representor is created,
the netdev of representor already exists, we can use that fact to simplify
the netdev affinity code.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Currently the steering for SQs created on representors is done on
creation, once we move to representors as ports of an IB device we need
the port argument which is given only at the modify QP stage, adjust the
code appropriately.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

In preparation of moving into a model of single IB device multiple ports
move rep to be part of the port structure. We mark a representor device by
setting is_rep, no functional change with this patch.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

On allocation we use the array size and on destruction num_ports, use the
array size of destruction as well, in this context the array corresponds
to the native/actual ports on the NIC so no need to adjust this logic for
representors.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

In downstream patches we will need access to the ports before doing any
stages, in order to set net device per representor.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Simplify the code and move the deallocation of the IB device into the
remove function.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Netdev info is stored in a separate array and holds data relevant on a per
port basis, move it to be part of the port struct.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Merge branch 'mlx5-next' into rdma.git for-next

From
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux

Required for dependencies on the next series

* branch 'mlx5-next':
  net/mlx5: E-Switch, add a new prio to be used by the RDMA side
  net/mlx5: E-Switch, don't use hardcoded values for FDB prios
  net/mlx5: Fix false compilation warning
  net/mlx5: Expose MPEIN (Management PCIE INfo) register layout
  net/mlx5: Add rate limit print macros
  net/mlx5: Add explicit bar address field
  net/mlx5: Replace dev_err/warn/info by mlx5_core_err/warn/info
  net/mlx5: Use dev->priv.name instead of dev_name
  net/mlx5: Make mlx5_core messages independent from mdev->pdev
  net/mlx5: Break load_one into three stages
  net/mlx5: Function setup/teardown procedures
  net/mlx5: Move health and page alloc init to mdev_init
  net/mlx5: Split mdev init and pci init
  net/mlx5: Remove redundant init functions parameter
  net/mlx5: Remove spinlock support from mlx5_write64
  net/mlx5: Remove unused MLX5_*_DOORBELL_LOCK macros
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Create a new prio in the FDB, it will be used when inserting steering rules
into the FDB from the RDMA side. We create a new PRIO so rules from the
net side and rules from the RDMA side won't be inserted to the same PRIO,
each side has it's own sandbox to play in.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

When creating the FDB prios, use the enum values already defined and not
the hardcoded values.
Signed-off-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>

cxgb4 has a simple non-dynamic use of get_netdev, so conversion is
straightforward.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Drivers that never change their ndev dynamically do not need to use
the get_netdev callback.
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>
Acked-by: NSelvin Xavier <selvin.xavier@broadcom.com>
Acked-by: NMichal Kalderon <michal.kalderon@marvell.com>
Acked-by: NAdit Ranadive <aditr@vmware.com>

In mhop 0 mode, 64*bt_num queues can be supported.
In mhop 1 mode, 32K*bt_num queues can be supported.
Config srqc_hop_num to 1 to support 1M SRQ queues.
Signed-off-by: Nchenglang <chenglang@huawei.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

With page combining, the assumption that number of SG entries in umem SGL
equal to number of system pages in umem no longer holds.

umem->sg_nents tracks the SG entries in umem SGL. Use it in
sg_pcopy_to_buffer() as opposed to ib_umem_num_pages(umem).

Fixes: d10bcf94 ("RDMA/umem: Combine contiguous PAGE_SIZE regions in SGEs")
Reported-by: NJason Gunthorpe <jgg@mellanox.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

This patch adds support of resource track for hip08 and take dumping cq
context state used for debugging as an example.  More resources track
supports for hns driver will be added in future.

The output should be as follows.
$ rdma res show cq dev hnseth0 -d
dev hnseth0 cqe 1023 users 2 poll-ctx WORKQUEUE pid 0 comm [ib_core] drv_state 2 drv_ceq
n 0 drv_cqn 0 drv_hopnum 1 drv_pi 0 drv_ci 0 drv_coalesce 0 drv_period 0 drv_cnt 0
Signed-off-by: NTao Tian <tiantao6@huawei.com>
Signed-off-by: NYangyang Li <liyangyang20@huawei.com>
Signed-off-by: Nchenglang <chenglang@huawei.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Convert SRQ allocation from drivers to be in the IB/core
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Simplify drivers by ensuring lifetime of ib_ah object. The changes
in .create_ah() go hand in hand with relevant update in .destroy_ah().

We will use this opportunity and convert .destroy_ah() to don't fail, as
it was suggested a long time ago, because there is nothing to do in case
of failure during destroy.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

AH objects are allocated in atomic context and those allocations should
be done with GFP_ATOMIC.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The ucontext and ufile should not be accessed via the uobject, all these
cases have an attrs so use that instead.
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

These should all go through udata now. Add mlx5_udata_to_mdev to convert
a udata into the struct mlx5_ib_dev as these call sites require.
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>