Use .cfg to configure the default bt priority boost value;
the default bt priority boost is 0xf0
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bt config command need to send before the init calibration command,
driver need to let uCode know that calibrations are being performed now
in order to assure antenna is not being taken to BT use during radio/dsp
reads/writes

Also, bt_coex_priorty_table command need to be send right after the
bt_config_command during init sequence. Followed by bt coex envelope
command to initialize and prepare uCode bt state machine
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When advanced bt coex enabled, uCode will send bt status
notification to driver, here add support for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

6000g2b hardware implements advance bluetooth coexist command,
implement base on the new API command strucutre.

Also increment the API 5 to support the advance BT/WIfi coex.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new 6000g2b hardware requires a different
bluetooth coexist implementation on the host,
this adds the command/notification definitions
for it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No code or function changes, just some cleanup work for
out-of-date comments
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change the define to more generic naming to match _agn devices
since the rssi calculation are common function for 5000 series and up
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Adding additional parameter in REPLY_RX_PHY_CMD, frame_time indicate the
frame's time on the air based on byte count and frame rate calculation
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

By default, aggregation time limit is 4000 uSec, add the parameter to
.cfg
to allow this parameter can be configure per device base if needed.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Set the minimum and maximum for aggregation time limit in uSec.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Only the IBSS manager, ie. the station that sent
the IBSS beacon last, should be replying to probe
responses. This requires implementing the mac80211
tx_last_beacon callback, which we can do thanks to
the ucode beacon notification.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"iwlagn: add statistic notification structure for WiFi/BT devices" added
several new '__attribute__ ((packed))' lines.  Change them to the
generic __packed.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

defines shouldn't be terminated with a
semicolon, the code using them should
supply it. Luckily these are not used
in a context where it matters.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Different devices have different size of phy calibration table; add
new TLV to specify the size. If the TLV is not part of uCode header, the
default table size will be used to make sure the backward
compatibilities.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

WiFi/BT combo devices has different statistics notification
structure, adding the support here to make sure the structure
align correctly.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

If its WiFi/BT combo device, the statistics notification sent by
uCode will include the additional BT related statistics counters.

Adding new data structure to support the new layout.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add wait_for_silence_timeout_cnt to statistics_dbg structure
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For newer devices (6000g2a and 6000g2b), the sensitivity table send to
uCode require additional table entries to help sensitivity calibration.

All the additional entries has fix data for now, but do expect the value
will be change in the future when device become more stable.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Code clean up to change name from having 5000 as part of name which easy
to confuse and think it is for 5000 series devices to more
generic _agn name since it is being used by multiple _agn devices.

No functional changes.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Adding flush callback support in the driver. Two type of flush can be
issued by mac80211:
1. drop = true: frame drop is ok, issue REPLY_TXFIFO_FLUSH host command
to uCode to drop all the frames in tx fifo queues; then return the
control back to mac80211
2. drop = false: wait for either all the frames in tx fifo queues been
transmitted, or timeout; then return the control back to mac80211

If the flush request coming from mac80211, mac80211 will make sure there
are no additional frames push down to driver before flush operation is
completed.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Add host command and structure for tx fifo queue flush
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

This bit need to be set for both RTS/CTS or CTS-to-self protection, if
CTS-to-self is used, then uCode will  check the RXON_FLG_SELF_CTS_EN
status. Change the name from TX_CMD_FLG_RTS_CTS_MSK to TX_CMD_FLAG_PROT_REQUIRE_MSK
to match the behavior of the bit setting.

Also update comments to reflect which hardware uses which of the TX command
flags.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

iwl4965_rx_mpdu_res_start is not 4695 specific, so rename it to more
general name iwl_rx_mpdu_res_start.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

REPLY_REMOVE_STA command is used
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

cleanup patch.

Use new __packed annotation in drivers/net/
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This constant is not used, and incorrect, since
the broadcast ID must be used for multicast too.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Move "tx power per chain" into ucode_tx_stats, it is debugging
information provided by uCode as part of statistics notification.

The "tx power per chain" parameters are optional parameters which only
supported by 6000 series device today; those are reserved fields for all
the other devices.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

The old firmware file type does not allow indicating
any firmware capabilities, which we frequently want
to make things easier.

This implements a new firmware type that is based on
a TLV structure, and adds a TLV for the maximum length
of probe requests in scans.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Some firmware versions don't behave properly when
passive scanning is requested on radar channels
without enabling active scanning on receiving a
good frame. Work around that issue by asking the
firmware to only enable the active scanning after
receiving a huge number of good frames, a number
that can never be reached during our dwell time.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

The flag name is a little misleading, this
flag instructs the device to ignore bluetooth
messages for purposes of frame transmissions,
so rename the flag to TX_CMD_FLG_IGNORE_BT.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

REPLY_TX_LINK_QUALITY_CMD was used by 4965, 5000 series and up
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Update to include additional tx command response status for "_agn"
devices.

The following status indicate the transmission was postponed:
  TX_STATUS_POSTPONE_DELAY
  TX_STATUS_POSTPONE_FEW_BYTES
  TX_STATUS_POSTPONE_BT_PRIO
  TX_STATUS_POSTPONE_QUIET_PERIOD
  TX_STATUS_POSTPONE_CALC_TTAK
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

When sys assert happen, driver will dump the error table information
provided by uCode. There are more information available but is not being
display by the driver; adding program counter and last host command the
to log to help uCode debugging.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Increase the buffer size for commands with "huge"
bit set. This has been recently observed for 6050 cards where
for even with huge bit set few commands were not properly allocated
memory with the command overwriting the buffer allocated for it..
Also add a check to see if command size exceeds the
maximum allowable size.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Number of calibration op-code are not used by driver, remove those from
iwl-commands.h
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Adding "bt_coex_active" module parameter for iwlcore to enable/disable
BT coexist; if bt_coex_active is true (default), uCode will do kill/defer
every time the priority line is asserted (BT is sending signals on the
priority line in the PCIx). By disable the bt_coex_active, uCode will
ignore the BT activity and perform the normal operation.

Users might experience transmit issue on some platform due to this
WiFi/BT co-exist problem. The possible symptoms are: NetworkManager and
other similar programs can scan and find all the available APs, but will
timeout and unable to associate with any of the APs; no out-going frames
can be found with wireless sniffer tools.

On those platforms, WiFi communication can be restored by set "bt_coex_active"
module parameter to "false"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Give better bit filed define and description for flag parameter
in REPLY_BT_CONFIG command:

flags:
 bit 0 - 1: BT channel announcement enabled
         0: disable
 bit 1 - 1: priority of BT device enabled
         0: disable
 bit 2 - 1: BT 2 wire support enabled
         0: disable
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support to configure missed beacon threshold, by default, if receive
"missed beacon" notification from uCode and has more than 5 consecutive
beacon missed, then perform sensitivity calibration; with this change,
allow user to adjust the missed beacon threshold from debugfs in case
more sensitivity calibration required for better performance in noisy
environment

The default value (=5) should be good enough for the normal condition,
but for very noisy environment, more sensitivity calibration could help
improve the throughput, so by setting the missed beacon threshold to
lower number, user might experience better performance result.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>