In [0] a user reported reproducible tx timeouts on RTL8168f except
PktCntrDisable is set and irq coalescing is enabled.
Realtek told me that they are not aware of any related hw issue on
this chip version, therefore root cause is still unknown. It's not
clear whether the issue affects one or more chip versions in general,
or whether issue is specific to reporter's system.
Due to this level of uncertainty, and due to the fact that I'm aware
of this one report only, let's apply the workaround on net-next only.
After this change setting irq coalescing via ethtool can reliably
avoid the issue on the affected system.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=207205Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let the compiler decide about inlining, and as confirmed by Eric it's
better to use WRITE_ONCE here to ensure that the descriptor ownership
is transferred to NIC immediately.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid the goto from the rx error handling branch into the else branch,
and in general avoid having the main rx work in the else branch.
In addition ensure proper reverse xmas tree order of variables in the
for loop.

No functional change intended.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to %pM instead of using custom code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert to %pM instead of using custom code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each trap registered with devlink is mapped to one or more Rx listeners.
These listeners allow the switch driver (e.g., mlxsw_spectrum) to
register a function that is called when a packet is received (trapped)
for a specific reason.

Currently, three arrays are used to describe the mapping between the
logical devlink traps and the Rx listeners.

Instead, get rid of these arrays and store all the information in one
array that is easier to validate and extend with more per-trap
information.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use one array to store all the information about all the trap groups
instead of hard coding it in code. This will be used in future patches
to disable certain functionality (e.g., policer binding) on a trap group
basis.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of maintaining an array of policers and a linked list, only
maintain an array.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'struct mlxsw_sp_trap_policer_item' is only used in one file, so move it
there.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After having switched to devm_mdiobus_register() also this remaining
call to mdiobus_unregister() can be removed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Core will now perform this check.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add driver level bulking to the XDP_TX action.

An array of frame descriptors is held for each Tx frame queue and
populated accordingly when the action returned by the XDP program is
XDP_TX. The frames will be actually enqueued only when the array is
filled. At the end of the NAPI cycle a flush on the queued frames is
performed in order to enqueue the remaining FDs.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building with Clang:

In file included from drivers/net/ethernet/ti/am65-cpsw-ethtool.c:15:
drivers/net/ethernet/ti/am65-cpts.h:58:12: warning: unused function
'am65_cpts_ns_gettime' [-Wunused-function]
static s64 am65_cpts_ns_gettime(struct am65_cpts *cpts)
           ^
drivers/net/ethernet/ti/am65-cpts.h:63:12: warning: unused function
'am65_cpts_estf_enable' [-Wunused-function]
static int am65_cpts_estf_enable(struct am65_cpts *cpts,
           ^
drivers/net/ethernet/ti/am65-cpts.h:69:13: warning: unused function
'am65_cpts_estf_disable' [-Wunused-function]
static void am65_cpts_estf_disable(struct am65_cpts *cpts, int idx)
            ^
3 warnings generated.

These functions need to be marked as inline, which adds __maybe_unused,
to avoid these warnings, which is the pattern for stub functions.

Fixes: ec008fa2 ("ethernet: ti: am65-cpts: add routines to support taprio offload")
Link: https://github.com/ClangBuiltLinux/linux/issues/1026Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Take DCBNL-related definitions out of the common en.h header,
Use a dedicated header file for exposing them.
Some need not to be exposed, use them locally in the .c file.
Use stubs to eliminate use of CONFIG_MLX5_CORE_EN_DCB in the
generic control flows.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, different formulas are used to estimate the space that may be
taken by WQEs in the SQ during a single packet transmit. This space is
called stop room, and it's checked in the end of packet transmit to find
out if the next packet could overflow the SQ. If it could, the driver
tells the kernel to stop sending next packets.

Many factors affect the stop room:

1. Padding with NOPs to avoid WQEs spanning over page boundaries.

2. Enabled and disabled offloads (TLS, upcoming MPWQE).

3. The maximum size of a WQE.

The padding is performed before every WQE if it doesn't fit the current
page.

The current formula assumes that only one padding will be required per
packet, and it doesn't take into account that the WQEs posted during the
transmission of a single packet might exceed the page size in very rare
circumstances. For example, to hit this condition with 4096-byte pages,
TLS offload will have to interrupt an almost-full MPWQE session, be in
the resync flow and try to transmit a near to maximum amount of data.

To avoid SQ overflows in such rare cases after MPWQE is added, this
patch introduces a more robust formula to estimate the stop room. The
new formula uses the fact that a WQE of size X will not require more
than X-1 WQEBBs of padding. More exact estimations are possible, but
they result in much more complex and error-prone code for little gain.

Before this patch, the TLS stop room included space for both INNOVA and
ConnectX TLS offloads that couldn't run at the same time anyway, so this
patch accounts only for the active one.
Signed-off-by: NMaxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

After enabled loopback packets for IPoIB, we need to drop these packets
that this HCA has replicated and came back to the same interface that
sent them.

Fixes: 4c6c615e ("net/mlx5e: IPoIB, Add PKEY child interface nic profile")
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Reviewed-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Enable loopback of unicast and multicast traffic for IPoIB enhanced
mode.
This will allow interfaces with the same pkey to communicate between
them e.g cloned interfaces that located in different namespaces.
Signed-off-by: NErez Shitrit <erezsh@mellanox.com>
Reviewed-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

It could be a chain of rules will do action CT again after CT NAT
Before this fix matching will break as we get into the CT table
after NAT changes and not CT NAT.
Fix this by adding pre ct and pre ct nat tables to skip ct/ct_nat
tables and go straight to post_ct table if ct/nat was already done.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Move mlx5_read_internal_timer() into lib/clock.c file as it is being
used there. As such, make this function a static one.

In addition, rearrange headers include to support function move.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: NAya Levin <ayal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, if one thread tries to add an entry to an autogrouped table
with no free matching group, while another thread is in the process of
creating a new matching autogroup, it doesn't wait for the new group
creation, and creates an unnecessary new autogroup.

Instead of skipping inactive, wait on the write lock of those groups.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Reviewed-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

mlx5_unload_one() is done with cleanup = true only once.

So instead of doing health wq drain inside the if(), directly do
during PCI device removal.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Having multiple error unwinding path are error prone.
Lets have just one error unwinding path.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

On systems with page size larger than 4K, a fwp object has few 4K chunks.
Fix a bug in fwp free flow where the chunk address was dropped and
fwp->addr was used instead (first chunk address). This caused a wrong
update of fwp->bitmask which later can cause errors in re-alloc fwp
chunk flow.

In order to fix this it, re-factor the release flow:
- Free 4k: Releases a specific 4k chunk inside the fwp, defined by
  starting address.
- Free fwp: Unconditionally release the whole fwp and its resources.
Free addr will call free fwp if all chunks were released, in order to do
code sharing.

In addition, fix npages to count for all released chunks correctly.

Fixes: c6168161 ("net/mlx5: Add support for release all pages event")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The cited patch assumes that all chuncks in a fw page belong to the same
function, thus the driver must dedicate fw page to the requesting
function, which is actually what was intedned in the original fw pages
allocator design, hence the fwp->func_id !

Up until the cited patch everything worked ok, but now "relase all pages"
is broken on systems with page_size > 4k.

Fix this by dedicating fw page to the requesting function id via adding a
func_id parameter to alloc_4k() function.

Fixes: c6168161 ("net/mlx5: Add support for release all pages event")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Rework and add support for dumping EOTID software context used by
TC-MQPRIO. Also track number of EOTIDs in use.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each traffic class, firmware handles up to 4 * MTU amount of data
per burst cycle. Under heavy load, this small buffer size is a
bottleneck when buffering large TSO packets in <= 1500 MTU case.
Increase the burst buffer size to 8 * MTU when supported.

Also, keep the driver's traffic class configuration API similar to
the firmware API counterpart.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Request credit update for every half credits consumed, including
the current request. Also, avoid re-trying to post packets when there
are no credits left. The credit update reply via interrupt will
eventually restore the credits and will invoke the Tx path again.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on the WRIOP version, the buffer size on the RX path must by a
multiple of 64 or 256. Handle this restriction properly by aligning down
the buffer size to the necessary value. Also, use the new buffer size
dynamically computed instead of the compile time one.

Fixes: 27c87486 ("dpaa2-eth: Use a single page per Rx buffer")
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlx5 driver have multiple memory models, which are also changed
according to whether a XDP bpf_prog is attached.

The 'rx_striding_rq' setting is adjusted via ethtool priv-flags e.g.:
 # ethtool --set-priv-flags mlx5p2 rx_striding_rq off

On the general case with 4K page_size and regular MTU packet, then
the frame_sz is 2048 and 4096 when XDP is enabled, in both modes.

The info on the given frame size is stored differently depending on the
RQ-mode and encoded in a union in struct mlx5e_rq union wqe/mpwqe.
In rx striding mode rq->mpwqe.log_stride_sz is either 11 or 12, which
corresponds to 2048 or 4096 (MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ).
In non-striding mode (MLX5_WQ_TYPE_CYCLIC) the frag_stride is stored
in rq->wqe.info.arr[0].frag_stride, for the first fragment, which is
what the XDP case cares about.

To reduce effect on fast-path, this patch determine the frame_sz at
setup time, to avoid determining the memory model runtime. Variable
is named frame0_sz to make it clear that this is only the frame
size of the first fragment.

This mlx5 driver does a DMA-sync on XDP_TX action, but grow is safe
as it have done a DMA-map on the entire PAGE_SIZE. The driver also
already does a XDP length check against sq->hw_mtu on the possible
XDP xmit paths mlx5e_xmit_xdp_frame() + mlx5e_xmit_xdp_frame_mpwqe().

V3+4: Change variable name first_frame_sz to frame0_sz

V2: Fix that frag_size need to be recalc before creating SKB.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NTariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Link: https://lore.kernel.org/bpf/158945348021.97035.12295039384250022883.stgit@firesoul

Intel drivers implement native AF_XDP zerocopy in separate C-files,
that have its own invocation of bpf_prog_run_xdp(). The setup of
xdp_buff is also handled in separately from normal code path.

This patch update XDP frame_sz for AF_XDP zerocopy drivers i40e, ice
and ixgbe, as the code changes needed are very similar.  Introduce a
helper function xsk_umem_xdp_frame_sz() for calculating frame size.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NBjörn Töpel <bjorn.topel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/158945347511.97035.8536753731329475655.stgit@firesoul

This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".

For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.

The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).

There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945347002.97035.328088795813704587.stgit@firesoul

This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".

For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.

The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).

There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945346494.97035.12809400414566061815.stgit@firesoul

This patch mirrors the changes to ixgbe in previous patch.

This VF driver doesn't support XDP_REDIRECT, but correct tailroom is
still necessary for BPF-helper xdp_adjust_tail.  In legacy-mode +
larger PAGE_SIZE, due to lacking tailroom, we accept that
xdp_adjust_tail shrink doesn't work.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945345984.97035.13518286183248025173.stgit@firesoul

This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".

For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.

The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).

There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945345455.97035.14334355929030628741.stgit@firesoul

The ixgbe driver have another memory model when compiled on archs with
PAGE_SIZE above 4096 bytes. In this mode it doesn't split the page in
two halves, but instead increment rx_buffer->page_offset by truesize of
packet (which include headroom and tailroom for skb_shared_info).

This is done correctly in ixgbe_build_skb(), but in ixgbe_rx_buffer_flip
which is currently only called on XDP_TX and XDP_REDIRECT, it forgets
to add the tailroom for skb_shared_info. This breaks XDP_REDIRECT, for
veth and cpumap.  Fix by adding size of skb_shared_info tailroom.

Maintainers notice: This fix have been queued to Jeff.

Fixes: 64530739 ("ixgbe: add initial support for xdp redirect")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link: https://lore.kernel.org/bpf/158945344946.97035.17031588499266605743.stgit@firesoul

The netronome nfp driver use PAGE_SIZE when xdp_prog is set, but
xdp.data_hard_start begins at offset NFP_NET_RX_BUF_HEADROOM.
Thus, adjust for this when setting xdp.frame_sz, as it counts
from data_hard_start.

When doing XDP_TX this driver is smart and instead of a full DMA-map
does a DMA-sync on with packet length. As xdp_adjust_tail can now
grow packet length, add checks to make sure that grow size is within
the DMA-mapped size.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/bpf/158945342911.97035.11214251236208648808.stgit@firesoul

To help reviewers these are the defines related to RCV_FRAG_LEN

 #define DMA_BUFFER_LEN	1536 /* In multiples of 128bytes */
 #define RCV_FRAG_LEN	(SKB_DATA_ALIGN(DMA_BUFFER_LEN + NET_SKB_PAD) + \
			 SKB_DATA_ALIGN(sizeof(struct skb_shared_info)))
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Cc: Sunil Goutham <sgoutham@marvell.com>
Cc: Robert Richter <rrichter@marvell.com>
Link: https://lore.kernel.org/bpf/158945342402.97035.12649844447148990032.stgit@firesoul

The mlx4 drivers size of memory backing the RX packet is stored in
frag_stride. For XDP mode this will be PAGE_SIZE (normally 4096).
For normal mode frag_stride is 2048.

Also adjust MLX4_EN_MAX_XDP_MTU to take tailroom into account.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Link: https://lore.kernel.org/bpf/158945341893.97035.2688142527052329942.stgit@firesoul

Frame size ENA_PAGE_SIZE is limited to 16K on systems with larger
PAGE_SIZE than 16K. Change ENA_XDP_MAX_MTU to also take into account
the reserved tailroom.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NSameeh Jubran <sameehj@amazon.com>
Cc: Arthur Kiyanovski <akiyano@amazon.com>
Link: https://lore.kernel.org/bpf/158945341384.97035.907403694833419456.stgit@firesoul

The driver code cpsw.c and cpsw_new.c both use page_pool
with default order-0 pages or their RX-pages.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/bpf/158945340875.97035.752144756428532878.stgit@firesoul