Some devices, e.g. the RTL8723BS bluetooth part, some USB attached devices,
completely drop from the bus on a system-suspend. These devices will
have their driver unbound and rebound on resume (when the dropping of
the bus gets detected) and will show up as a new HCI after resume.

These devices do not benefit from the suspend / resume handling work done
by the hci_suspend_notifier. At best this unnecessarily adds some time to
the suspend/resume time. But this may also actually cause problems, if the
code doing the driver unbinding runs after the pm-notifier then the
hci_suspend_notifier code will try to talk to a device which is now in
an uninitialized state.

This commit adds a new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk which allows
drivers to opt-out of the hci_suspend_notifier when they know beforehand
that their device will be fully re-initialized / reprobed on resume.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Queries tx power via HCI_LE_Read_Transmit_Power command when the hci
device is initialized, and stores resulting min/max LE power in hdev
struct. If command isn't available (< BT5 support), min/max values
both default to HCI_TX_POWER_INVALID.

This patch is manually verified by ensuring BT5 devices correctly query
and receive controller tx power range.
Reviewed-by: NSonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: NDaniel Winkler <danielwinkler@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: NSathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: NSathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.

This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.

So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.

Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.

So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.

Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.

That way we can narrow down ranges of fakes for each of them.

e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
     support BT 1.1 only; so it's a dead giveaway when some
     third-party BT 4.0 dongle reuses it.

So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.

Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
  IC markings on 0x7558: FR3191AHAL 749H15143 (???)

https://bugzilla.kernel.org/show_bug.cgi?id=60824

Fixes: 81cac64b (Deal with USB devices that are faking CSR vendor)
Reported-by: NMichał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: NMike Johnson <yuyuyak@gmail.com>
Tested-by: NRicardo Rodrigues <ekatonb@gmail.com>
Tested-by: NM.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: NOussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: NIsmael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: NIsmael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used.  This patch fixes this issue by using
the configured min/max value.

This was validated by setting min/max in main.conf and making sure the
right setting is applied:

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25                                          #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Reviewed-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: NDaniel Winkler <danielwinkler@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To enable platform specific experimental features, introduce this new set of
management commands and events.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This change adds the relevant driver and quirk to allow drivers to
report the le_states as being trustworthy.

This has historically been disabled as controllers did not reliably
support this. In particular, this will be used to relax this condition
for controllers that have been well tested and reliable.

	/* Most controller will fail if we try to create new connections
	 * while we have an existing one in slave role.
	 */
	if (hdev->conn_hash.le_num_slave > 0)
		return NULL;
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The list of LE features constants has gotten a bit confused. It lost the
order and gained duplicated. Clean this up.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.

Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.

This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: NArchie Pusaka <apusaka@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch assigns the next free HCI device identifier to Bluetooth
devices based on VIRTIO devices.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Reviewed-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: NSathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: NAbhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch provides a mechanism for MGMT interface client to query the
capability of the controller to support WBS.
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change simply fixes a few typos in the quirk definitions.
Signed-off-by: NAlain Michaud <alainm@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Extended advertising Data is set during bluetooth initialization
by default which causes InvalidHCICommandParameters when setting
Extended advertising parameters.

As per Core Spec 5.2 Vol 2, PART E, Sec 7.8.53, for
advertising_event_property LE_LEGACY_ADV_DIRECT_IND does not
supports advertising data when the advertising set already
contains some, the controller shall return erroc code
'InvalidHCICommandParameters(0x12).

So it is required to remove adv set for handle 0x00. since we use
instance 0 for directed adv.
Signed-off-by: NSathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

These adds the HCI definitions for handling CIS connections along with
ISO data packets.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This handles LE PHY Update Complete event and store both tx_phy and
rx_phy into hci_conn.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.

As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: NSpoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.

The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.

This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.

Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64)                                  0.352340
= Note: Bluetooth subsystem version 2.22                               0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0)               [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84                                 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm)                      [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14                  {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14                {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1       {0x0003} [hci0] 27.302310
        Address type: 0x06
          LE Public
          LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6   #1 [hci0] 27.302496
        Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4                 #2 [hci0] 27.419117
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7  #3 [hci0] 27.419244
        Type: Active (0x01)
        Interval: 11.250 msec (0x0012)
        Window: 11.250 msec (0x0012)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #4 [hci0] 27.420131
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2      #5 [hci0] 27.420259
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                 #6 [hci0] 27.420969
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #7 [hci0] 27.421983
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4        {0x0003} [hci0] 27.422059
      Start Discovery (0x0023) plen 1
        Status: Success (0x00)
        Address type: 0x06
          LE Public
          LE Random
@ MGMT Event: Discovering (0x0013) plen 2             {0x0003} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0002} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0001} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
Signed-off-by: NJoão Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve
the public Bluetooth address from the firmware node property
'local-bd-address'. If quirk is set and the property does not exist
or is invalid the controller is marked as unconfigured.
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Reviewed-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: NBalakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.
Signed-off-by: NAnkit Navik <ankit.p.navik@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add the definitions for LE address resolution enable HCI commands.
When the LE address resolution enable gets changed via HCI commands
make sure that flag gets updated.
Signed-off-by: NAnkit Navik <ankit.p.navik@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Using HCI_VENDOR_PKT for vendor specific events does work since it has
also the value 0xff, but it is actually the packet type indicator
constant and not the event constant. So introduce HCI_EV_VENDOR and
use it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that
runs setup() after every open() and not just after the first open().
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for advertising in primary and secondary
channel on different PHYs. User can add the phy preference in
the flag based on which phy type will be added in extended
advertising parameter would be set.

@ MGMT Command: Add Advertising (0x003e) plen 11
        Instance: 1
        Flags: 0x00000200
          Advertise in CODED on Secondary channel
        Duration: 0
        Timeout: 0
        Advertising data length: 0
        Scan response length: 0
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0000
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE Coded (0x03)
        Secondary max skip: 0x00
        Secondary PHY: LE Coded (0x03)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This event comes after connection complete event for incoming
connections. Since we now have different random address for
each instance, conn resp address is assigned from this event.

As of now only connection part is handled as we are not
enabling duration or max num of events while starting ext adv.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.

Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.

This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.

< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
        Advertising handle: 0x00
        Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If ext adv is enabled then use ext adv to disable as well.
Also remove the adv set during LE disable.

< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements Set Ext Adv data and Set Ext Scan rsp data
if controller support extended advertising.

Currently the operation is set as Complete data and fragment
preference is set as no fragment

< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
        Handle: 0x00
        Operation: Complete extended advertising data (0x03)
        Fragment preference: Minimize fragmentation (0x01)
        Data length: 0x15
        16-bit Service UUIDs (complete): 2 entries
          Heart Rate (0x180d)
          Battery Service (0x180f)
        Name (complete): Test LE
        Company: Google (224)
          Data: 0102
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Data (0x08|0x0037) ncmd 1
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.

This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0010
          Use legacy advertising PDUs: ADV_NONCONN_IND
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE 1M (0x01)
        Secondary max skip: 0x00
        Secondary PHY: LE 1M (0x01)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
      LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
        Status: Success (0x00)
        TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
        Extended advertising: Enabled (0x01)
        Number of sets: 1 (0x01)
        Entry 0
          Handle: 0x00
          Duration: 0 ms (0x00)
          Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch reads the number of advertising sets in the controller
during init and save it in hdev.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch defines the extended ADV types and handle it in ADV report.
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use the PHYs selected in Set Phy Configuration management command
while scanning.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 13
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x05
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
        Entry 1: LE Coded
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This also add macros for checking LMP support for different
pkt_types
Signed-off-by: NJaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>