This patch adds support of ethtool -K to enable/disable
hardware GRO in HNS3 PF/VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "FE bit" in the description means the last description for
a packets. When HW GRO enable, HW write data to ring every
packet/buffer, there is greater probability that driver handle
with the describtion but HW still not set the "FE bit".

When drier handle the packet and HW still not set "FE bit",
driver stores skb and bd_num in rx ring, and continue to use the
skb and bd_num in next napi.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 hardware Revision B(=0x21) supports Hardware GRO feature. This
patch enables this feature in the HNS3 PF/VF driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move IRQ configuration for IP101A/G from config_init to config_intr
callback. Reasons:

1. This allows phylib to disable interrupts if needed.
2. Icplus was the only driver supporting interrupts w/o defining a
   config_intr callback. Now we can add a phylib plausibility check
   disabling interrupt mode if one of the two irq-related callbacks
   isn't defined.

I don't own hardware with this PHY, and the change is based on the
datasheet for IP101A LF (which is supposed to be register-compatible
with IP101A/G). Change is compile-tested only.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: abm: track all Qdiscs

Our Qdisc offload so far has been very simplistic.  We held
and array of marking thresholds and statistics sized to the
number of PF queues.  This was sufficient since the only
configuration we supported was single layer of RED Qdiscs
(on top of MQ or not, but MQ isn't really about queuing).

As we move to add more Qdiscs it's time to actually try to
track the full Qdisc hierarchy.  This allows us to make sure
our offloaded configuration reflects the SW path better.
We add graft notifications to MQ and RED (PRIO already sends
them) to allow drivers offloading those to learn how Qdiscs
are linked.  MQ graft gives us the obvious advantage of being
able to track when Qdiscs are shared or moved.  It seems
unlikely HW would offload RED's child Qdiscs but since the
behaviour would change based on linked child we should
stop offloading REDs with modified child.  RED will also
handle the child differently during reconfig when limit
parameter is set - so we have to inform the drivers about
the limit, and have them reset the child state when
appropriate.

The NFP driver will now allocate a structure to track each
Qdisc and link it to its children.  We will also maintain
a shadow copy of threshold settings - to save device writes
and make it easier to apply defaults when config is
re-evaluated.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation of handling more Qdisc types switch to a different
offload strategy.  We have now recreated the Qdisc hierarchy in
the driver.  Every time the hierarchy changes parse it, and update
the configuration of the HW accordingly.

While at it drop the support of pretending that we can instantiate
a single queue on a multi-queue device in HW/FW.  MQ is now required,
and each queue will have its own instance of RED.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new driver Qdisc structure to keep track of parameters
of RED Qdiscs.  This way as the Qdisc moves around in the hierarchy
we will be able to configure the HW appropriately.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RED qdisc will replace its child Qdisc with a new FIFO queue if
it is reconfigured and the limit parameter is not 0.

This means that when it's created with limit of 0 it will have no FIFO,
and all packets will be dropped.  If it's changed and limit is specified
it will loose its existing child (implicit graft).  Make sure we mark
RED Qdisc child as NFP_QDISC_UNTRACKED if its not the expected FIFO.

nfp_abm_qdisc_replace() will return 1 if Qdisc already existed.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RED qdisc's limit parameter changes the behaviour of the qdisc,
for instance if it's set to 0 qdisc will drop all the packets.

When replace operation happens and parameter is set to non-0
a new fifo qdisc will be instantiated and replace the old child
qdisc which will be destroyed.

Drivers need to know the parameter, even if they don't impose
the actual limit to be able to reliably reconstruct the Qdisc
hierarchy.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using graft notifications recreate in the driver the full Qdisc
hierarchy.  Keep track of how many times each Qdisc is attached
to the hierarchy to make sure we don't offload Qdiscs which are
attached multiple times (device queues can't be shared).  For
graft events of Qdiscs we don't know exist make the child as
invalid/untracked.

Note that MQ Qdisc doesn't send destruction events reliably when
device is dismantled, so we need to manually clean out the
children otherwise we'd think Qdiscs which are still in use
are getting freed.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers offloading Qdiscs should have reasonable certainty
the offloaded behaviour matches the SW path.  This is impossible
if the driver does not know about all Qdiscs or when Qdiscs move
and are reused.  Send a graft notification from MQ.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers offloading Qdiscs should have reasonable certainty
the offloaded behaviour matches the SW path.  This is impossible
if the driver does not know about all Qdiscs or when Qdiscs move
and are reused.  Send a graft notification from RED.  The drivers
are expected to simply stop offloading the Qdisc, if a non-standard
child is ever grafted onto it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To keep track of Qdisc hierarchy allocate a table for children
for each Qdisc.  RED Qdisc can only have one child.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep track of which Qdisc is currently root.  We need to implement
TC_SETUP_ROOT_QDISC handling, and for completeness also clear the
root Qdisc pointer when it's freed.  TC_SETUP_ROOT_QDISC isn't always
sent when device is dismantled.

Remembering the root Qdisc will allow us to build the entire hierarchy
in following patches.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers are currently not notified when a Qdisc is grafted as root.
This requires special casing Qdiscs added with parent = TC_H_ROOT in
the driver.  Also there is no notification sent to the driver when
an existing Qdisc is grafted as root.

Add this very simple notifications, drivers should now be able to
track their Qdisc tree fully.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate an object corresponding to any offloaded qdisc we are
informed about by the kernel.  Not only the qdiscs we have a
chance of offloading.

The count of created objects will be used to decide whether
the ethtool TC offload can be disabled, since otherwise we may
miss destroy commands.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of writing the threshold out when Qdisc is configured
and not remembering it move to a scheme where we remember all
thresholds.  When configuration changes parse the offloaded
Qdiscs and set thresholds appropriately.

This will help future extensions.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename qdiscs member to red_qdiscs.  One of following patches will
use the name qdiscs for tracking all qdisc types.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: add rx-flow filter support

In this patchset the rx-flow filters functionality and vlan filter offloads
are implemented.

The rules in NIC hardware have fixed order and priorities.
To support this, the locations of filters from ethtool perspective are also fixed:

* Locations 0 - 15 for VLAN ID filters
* Locations 16 - 31 for L2 EtherType and PCP filters
* Locations 32 - 39 for L3/L4 5-tuple filters (locations 32, 36 for IPv6)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since it uses the same NIC table as rx flow vlan filter therefore
rx-flow vlan filter accepts only vlans that present on the interface
in case of rx-vlan-filter is on.
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

L2 EtherType filters allows to filter packet by EtherType field or
both EtherType and User Priority (PCP) field of 802.1Q.
UserPriority (vlan) parameter must be accompanied by mask 0x1FFF. That
is to distinguish VLAN filter from L2 Ethertype filter with
UserPriority since both User Priority and VLAN ID are passed in the
same 'vlan' parameter.

Example:
To add a filter that directs IP4 packess of priority 3 to queue 3:
ethtool -N <ethX> flow-type ether proto 0x800 vlan 0x600 m 0x1FFF \
action 3 loc 16
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VLAN filter (VLAN id) is compared against 16 filters.
VLAN id must be accompanied by mask 0xF000. That is to distinguish
VLAN filter from L2 Ethertype filter with UserPriority since both
User Priority and VLAN ID are passed in the same 'vlan' parameter.
Flow type may be any as  it is not matched for VLAN filter.
Due to fixed order of the rules in the NIC, the location 0-15 are
reserved for vlan filters.

Example:
To add a rule that directs packets from VLAN 2001 to queue 5:
ethtool -N <ethX> flow-type ip4 vlan 2001 m 0xF000 action 5 loc 0
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support of L3/L4 5-tuple {protocol, src-ip, dst-ip, src-port, dst-port}
filters. Mask is not supported. Src-port and dst-port are only compared for
TCP/UDP/SCTP packets. Both IPv4 and IPv6 are supported.
The supported actions are the drop and the queue assignment.
Due to fixed order of the rules in the NIC, the location 32-39 are
reserved for L3/L4 5-tuple filters. The locations 32 and 36 are
reserved for IPv6 filters.

Examples:
sudo ethtool -N eth0 flow-type ip6 src-ip 2001:db8:0:f101::2 \
dst-ip 2001:db8:0:f101::5 action -1 loc 36

sudo ethtool -N eth0 flow-type udp4 src-ip 10.0.0.4 \
dst-ip 10.0.0.7 src-port 2000 dst-port 2001 action 2 loc 32
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add infrastructure to support ntuple filter configuration.
Add rule, remove rule, reapply on interface up.
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing register definitions and the functions accessing them
related to rx-flow filters.
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
net: ethernet: ti: cpsw: allow vlan h/w timestamping

The patchset adds several improvements and allows vlan h/w ts.

Based on net-next/master
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow vlan tagged packets to be timestamped, as no any restrictions
for this.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each slave has it's own receive timestamp filter. But cpts rx/tx
timestamp enable flags are used to allow ts retrieve only for one
user. This limitation causes data path redundancy and setting overlap
if cpsw module is in dual-mac mode for instance.

If rx ts is enabled only for one port - the second interface must expect
every incoming packet to be PTP packet w/o absolutely any reason, and if
it's PTP - do unneeded stuff, as rx filter for second port is not set
and cpts fifo is not supposed to contain appropriate ts event.
That's not correct.

So, to fix control overlap and avoid redundant CPU cycles, the patch
splits rx/tx ts enable flags between network devices. After the patch,
PTP timestamping still should be used for only one port (or PTP id
counter has to be different for both ports as cpts IP is common).
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The overflow event is running with 1 jiffy in case if txq is not
empty, but it can be emptied completely only if next tx event
consumes skb or deletes staled skb from the txq. In case of staled
skb, that can happen for some unpredictable reason (the ts event was
lost or timed out), the overflow event can be generated quite long
time consuming CPU w/o reason before next tx event happens. To avoid
it, purge txq before increasing overflow event rate.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The msgtype and seqid that is smth that belongs to event for
comparison but not for staled txq skb.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent change modified variable advertising from a u32 to a link mode
array and left the u32 zero comparison, so essential we now have an array
being compared to null which is not the intention. Fix this by using the
call to linkmode_empty to check if advertising is all zero.

Detected by CoverityScan, CID#1475424 ("Array compared against 0")

Fixes: 3c1bcc86 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: add support for sk_reuseport

sctp sk_reuseport allows multiple socks to listen on the same port and
addresses, as long as these socks have the same uid. This works pretty
much as TCP/UDP does, the only difference is that sctp is multi-homing
and all the bind_addrs in these socks will have to completely matched,
otherwise listen() will return err.

The below is when 5 sockets are listening on 172.16.254.254:6400 on a
server, 26 sockets on a client connect to 172.16.254.254:6400 and each
may be processed by a different socket on the server which is selected
by hash(lport, pport, paddr) in reuseport_select_sock():

 # ss --sctp -nn
   State      Recv-Q Send-Q        Local Address:Port     Peer Address:Port
   LISTEN     0      10           172.16.254.254:6400                *:*
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.2.1:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.2.4:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.3.3:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.3.4:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.5.2:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.5.3:1234
   LISTEN     0      10           172.16.254.254:6400                *:*
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.1.3:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.1.4:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.3.2:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.4.1:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.4.2:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.4.3:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.4.4:1234
   LISTEN     0      10           172.16.254.254:6400                *:*
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.1.2:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.3.5:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.4.5:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400   172.16.253.253:1234
   LISTEN     0      10           172.16.254.254:6400                *:*
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.2.2:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.2.3:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.5.4:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.5.5:1234
   LISTEN     0      10           172.16.254.254:6400                *:*
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.1.1:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.1.5:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.2.5:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.3.1:1234
   `- ESTAB   0      0       172.16.254.254%eth1:6400       172.16.5.1:1234
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When socks' sk_reuseport is set, the same port and address are allowed
to be bound into these socks who have the same uid.

Note that the difference from sk_reuse is that it allows multiple socks
to listen on the same port and address.
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a part of sk_reuseport support for sctp. It defines a helper
sctp_bind_addrs_check() to check if the bind_addrs in two socks are
matched. It will add sock_reuseport if they are completely matched,
and return err if they are partly matched, and alloc sock_reuseport
if all socks are not matched at all.

It will work until sk_reuseport support is added in
sctp_get_port_local() in the next patch.

v1->v2:
  - use 'laddr->valid && laddr2->valid' check instead as Marcelo
    pointed in sctp_bind_addrs_check().
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a part of sk_reuseport support for sctp, and it selects a
sock by the hashkey of lport, paddr and dport by default. It will
work until sk_reuseport support is added in sctp_get_port_local()
in the next patch.

v1->v2:
  - define lport as __be16 instead of __be32 as Marcelo pointed in
    __sctp_rcv_lookup_endpoint().
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/phy/marvell.c: In function 'm88e1510_config_init':
drivers/net/phy/marvell.c:850:7: warning:
 variable 'pause' set but not used [-Wunused-but-set-variable]

It not used any more after commit 3c1bcc86 ("net: ethernet: Convert phydev
advertize and supported from u32 to link mode")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "One last pull request before heading to Vancouver for LPC, here we have:

   1) Don't forget to free VSI contexts during ice driver unload, from
      Victor Raj.

   2) Don't forget napi delete calls during device remove in ice driver,
      from Dave Ertman.

   3) Don't request VLAN tag insertion of ibmvnic device when SKB
      doesn't have VLAN tags at all.

   4) IPV4 frag handling code has to accomodate the situation where two
      threads try to insert the same fragment into the hash table at the
      same time. From Eric Dumazet.

   5) Relatedly, don't flow separate on protocol ports for fragmented
      frames, also from Eric Dumazet.

   6) Memory leaks in qed driver, from Denis Bolotin.

   7) Correct valid MTU range in smsc95xx driver, from Stefan Wahren.

   8) Validate cls_flower nested policies properly, from Jakub Kicinski.

   9) Clearing of stats counters in mc88e6xxx driver doesn't retain
      important bits in the G1_STATS_OP register causing the chip to
      hang. Fix from Andrew Lunn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  act_mirred: clear skb->tstamp on redirect
  net: dsa: mv88e6xxx: Fix clearing of stats counters
  tipc: fix link re-establish failure
  net: sched: cls_flower: validate nested enc_opts_policy to avoid warning
  net: mvneta: correct typo
  flow_dissector: do not dissect l4 ports for fragments
  net: qualcomm: rmnet: Fix incorrect assignment of real_dev
  net: aquantia: allow rx checksum offload configuration
  net: aquantia: invalid checksumm offload implementation
  net: aquantia: fixed enable unicast on 32 macvlan
  net: aquantia: fix potential IOMMU fault after driver unbind
  net: aquantia: synchronized flow control between mac/phy
  net: smsc95xx: Fix MTU range
  net: stmmac: Fix RX packet size > 8191
  qed: Fix potential memory corruption
  qed: Fix SPQ entries not returned to pool in error flows
  qed: Fix blocking/unlimited SPQ entries leak
  qed: Fix memory/entry leak in qed_init_sp_request()
  inet: frags: better deal with smp races
  net: hns3: bugfix for not checking return value
  ...

Merge tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix build errors in binrpm-pkg and bindeb-pkg targets

 - fix false positive matches in merge_config.sh

 - fix build version mismatch in deb-pkg target

 - fix dtbs_install handling in (bin)deb-pkg target

 - revert a commit that allows setlocalversion to write to source tree

* tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  builddeb: Fix inclusion of dtbs in debian package
  Revert "scripts/setlocalversion: git: Make -dirty check more robust"
  kbuild: deb-pkg: fix too low build version number
  kconfig: merge_config: avoid false positive matches from comment lines
  kbuild: deb-pkg: fix bindeb-pkg breakage when O= is used
  kbuild: rpm-pkg: fix binrpm-pkg breakage when O= is used