The ice_init_all_ctrlq and ice_shutdown_all_ctrlq functions create and
destroy the locks used to protect the send and receive process of each
control queue.

This is problematic, as the driver may use these functions to shutdown
and re-initialize the control queues at run time. For example, it may do
this in response to a device reset.

If the driver failed to recover from a reset, it might leave the control
queues offline. In this case, the locks will no longer be initialized.
A later call to ice_sq_send_cmd will then attempt to acquire a lock that
has been destroyed.

It is incorrect behavior to access a lock that has been destroyed.

Indeed, ice_aq_send_cmd already tries to avoid accessing an offline
control queue, but the check occurs inside the lock.

The root of the problem is that the locks are destroyed at run time.

Modify ice_init_all_ctrlq and ice_shutdown_all_ctrlq such that they no
longer create or destroy the locks.

Introduce new functions, ice_create_all_ctrlq and ice_destroy_all_ctrlq.
Call these functions in ice_init_hw and ice_deinit_hw.

Now, the control queue locks will remain valid for the life of the
driver, and will not be destroyed until the driver unloads.

This also allows removing a duplicate check of the sq.count and
rq.count values when shutting down the controlqs. The ice_shutdown_ctrlq
function already checks this value under the lock. Previously
commit dec64ff1 ("ice: use [sr]q.count when checking if queue is
initialized") needed this check to happen outside the lock, because it
prevented duplicate attempts at destroying the locks.

The driver may now safely use ice_init_all_ctrlq and
ice_shutdown_all_ctrlq while handling reset events, without causing the
locks to be invalid.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are always setting prefena to 0. This is causing the
hardware to only fetch descriptors when there are none free in the cache
for a received packet instead of prefetching when it has used the last
descriptor regardless of incoming packets. Fix this by allowing the
hardware to prefetch Rx descriptors.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When interrupt tracking was refactored, during rebuild, the call to
ice_vsi_setup_vector_base() was inadvertently removed from the PF VSI
instead of being removed from the VF VSI. During reset, the failure to
properly setup the vector base generates a call trace. Correct this so
that resets/rebuilds properly complete.

Fixes: cbe66bfe ("ice: Refactor interrupt tracking")
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, ice_stat_update32 and ice_stat_update40 will limit the
value of the software statistic to 32 or 40 bits wide, depending on
which register is being read.

This means that if a driver is running for a long time, the displayed
software register values will roll over to zero at 40 bits or 32 bits.

This occurs because the functions directly assign the difference between
the previous value and current value of the hardware statistic.

Instead, add this value to the current software statistic, and then
update the previous value.

In this way, each time ice_stat_update40 or ice_stat_update32 are
called, they will increment the software tracking value by the
difference of the hardware register from its last read. The software
tracking value will correctly count up until it overflows a u64.

The only requirement is that the ice_stat_update functions be called at
least once each time the hardware register overflows.

While we're fixing ice_stat_update40, modify it to use rd64 instead of
two calls to rd32. Additionally, drop the now unnecessary hireg
function parameter.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for reporting link partner advertising when
ETHTOOL_GLINKSETTINGS defined. Get pause param reports the Tx/Rx
pause configured, and then ethtool issues ETHTOOL_GSET ioctl and
ice_get_settings_link_up reports the negotiated Tx/Rx pause. Negotiated
pause frame report per IEEE 802.3-2005 table 288-3.

$ ethtool --show-pause ens6f0
Pause parameters for ens6f0:
Autonegotiate:  on
RX:             on
TX:             on
RX negotiated:  on
TX negotiated:  on

$ ethtool ens6f0
Settings for ens6f0:
        Supported ports: [ FIBRE ]
        Supported link modes:   25000baseCR/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Supported FEC modes: None BaseR RS
        Advertised link modes:  25000baseCR/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: None BaseR RS
        Link partner advertised link modes:  Not reported
        Link partner advertised pause frame use: Symmetric
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 25000Mb/s
        Duplex: Full
        Port: Direct Attach Copper
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes

When ETHTOOL_GLINKSETTINGS is not defined, get pause param reports the
negotiated Tx/Rx pause.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

"error" is unneeded,just return 0
Signed-off-by: NDing Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A few lines above, we have:
   tx_size = BIT(tx->order);

So use 'tx_size' directly to be consistent with the way 'rx->descs_cpu' and
'rx->descs_dma' are computed below.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Give a proper boottime_ns value for netlink RX to avoid scan
issues here.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20190729160605.1074-1-johannes@sipsolutions.netSigned-off-by: NJohannes Berg <johannes.berg@intel.com>

Add Microchip KSZ8795 DSA driver.
Signed-off-by: NTristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NStephen Boyd <swboyd@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: NJonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define the 57508, 57504, and 57502 chip IDs that are all part of the
BNXT_CHIP_P5 family of chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the new TPA feature in the 57500 chips, we need to discover the
feature first before setting up the netdev features.  Refactor the
the firmware probe and init logic more cleanly into 2 functions and
and make these calls before setting up the netdev features.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the new expanded TPA v2 counters on 57500 B0 chips for
ethtool -S.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new TPA implemantation has additional TPA counters that extend the
per-ring statistics block.  Allocate the proper size accordingly.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code assumes that the per ring statistics counters are
fixed.  In newer chips that support a newer version of TPA, the
TPA counters are also changed.  Refactor the code by defining these
counter names in arrays so that it is easy to add a new array for
a new set of counters supported by the newer chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a more optimized hardware GRO function to setup the SKB on 57500
chips.  Some workaround code is no longer needed on 57500 chips and
the pseudo checksum is also calculated in hardware, so no need to
do the software pseudo checksum in the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new TPA feature on 57500 supports a larger number of concurrent TPAs
(up to 1024) divided among the functions.  We need to add some logic to
map the hardware TPA ID to a software index that keeps track of each TPA
in progress.  A 1:1 direct mapping without translation would be too
wasteful as we would have to allocate 1024 TPA structures for each RX
ring on each PCI function.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With all the previous refactoring, the TPA fast path can now be
modified slightly to support TPA on the new chips.  The main
difference is that the agg completions are retrieved differently using
the bnxt_get_tpa_agg_p5() function on the new chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 57500 chips, hardware GRO mode cannot be determined from the TPA
end, so we need to check bp->flags to determine if we are in hardware
GRO mode or not.  Modify bnxt_set_features so that the TPA flags
in bp->flags don't change until the device is closed.  This will ensure
that the fast path can safely rely on bp->flags to determine the
TPA mode.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 2 GRO functions to set up the hardware GRO SKB fields for 2
different hardware chips have practically identical logic for
tunneled packets.  Refactor the logic into a separate bnxt_gro_tunnel()
function that can be used by both functions.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the new 57500 chips, these new RX_AGG completions are not coalesced
at the TPA_END completion.  Handle these by storing them in the
array in the bnxt_tpa_info struct, as they are seen when processing
the CMPL ring.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an aggregation array to bnxt_tpa_info struct to keep track of the
aggregation completions.  The aggregation completions are not
completed at the TPA_END completion on 57500 chips so we need to
keep track of them.  The array is only allocated on the new chips
when required.  An agg_count field is also added to keep track of the
number of these completions.

The maximum concurrent TPA is now discovered from firmware instead of
the hardcoded 64.  Add a new bp->max_tpa to keep track of maximum
configured TPA.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor the TPA logic slightly, so that the code can be more easily
extended to support TPA on the new 57500 chips.  In particular, the
logic to get the next aggregation completion is refactored into a
new function bnxt_get_agg() so that this operation is made more
generalized.  This operation will be different on the new chip in TPA
mode.  The logic to recycle the aggregation buffers has a new start
index parameter added for the same purpose.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new chips have a slightly modified TPA interface for LRO/GRO_HW.
Modify the TPA structures so that the same structures can also be
used on the new chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Among the changes are new CoS discard counters and new ctx_hw_stats_ext
struct for the latest 5750X B0 chips.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have an ERPS (Ethernet Ring Protection Switching) setup involving
mv88e6250 switches which we're in the process of switching to a BSP
based on the mainline driver. Breaking any link in the ring works as
expected, with the ring reconfiguring itself quickly and traffic
continuing with almost no noticable drops. However, when plugging back
the cable, we see 5+ second stalls.

This has been tracked down to the userspace application in charge of
the protocol missing a few CCM messages on the good link (the one that
was not unplugged), causing it to broadcast a "signal fail". That
message eventually reaches its link partner, which responds by
blocking the port. Meanwhile, the first node has continued to block
the port with the just plugged-in cable, breaking the network. And the
reason for those missing CCM messages has in turn been tracked down to
the VTU apparently being too busy servicing load/purge operations that
the normal lookups are delayed.

Initial state, the link between C and D is blocked in software.

     _____________________
    /                     \
   |                       |
   A ----- B ----- C *---- D

Unplug the cable between C and D.

     _____________________
    /                     \
   |                       |
   A ----- B ----- C *   * D

Reestablish the link between C and D.
     _____________________
    /                     \
   |                       |
   A ----- B ----- C *---- D

Somehow, enough VTU/ATU operations happen inside C that prevents
the application from receving the CCM messages from B in a timely
manner, so a Signal Fail message is sent by C. When B receives
that, it responds by blocking its port.

     _____________________
    /                     \
   |                       |
   A ----- B *---* C *---- D

Very shortly after this, the signal fail condition clears on the
BC link (some CCM messages finally make it through), so C
unblocks the port. However, a guard timer inside B prevents it
from removing the blocking before 5 seconds have elapsed.

It is not unlikely that our userspace ERPS implementation could be
smarter and/or is simply buggy. However, this patch fixes the symptoms
we see, and is a small optimization that should not break anything
(knock wood). The idea is simply to avoid doing an VTU load of an
entry identical to the one already present. To do that, we need to
know whether mv88e6xxx_vtu_get() actually found an existing entry, or
has just prepared a struct mv88e6xxx_vtu_entry for us to load. To that
end, let vlan->valid be an output parameter. The other two callers of
mv88e6xxx_vtu_get() are not affected by this patch since they pass
new=false.
Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a previous attempt to use xmit_more, but the change had to be
reverted because under load sometimes a transmit timeout occurred [0].
Maybe this was caused by a missing memory barrier, the new attempt
keeps the memory barrier before the call to netif_stop_queue like it
is used by the driver as of today. The new attempt also changes the
order of some calls as suggested by Eric.

[0] https://lkml.org/lkml/2019/2/10/39Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use resource_size to calcuate ioremap size and make
the code simpler.
Signed-off-by: NDing Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_info() is more appropriate for printing messages when driver
initialization done, so switch to dev_info().
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware supports 0.5K, 1K, 2K, 4K RX buffer size, the
RX buffer can not be reused because the hns3_page_order
return 0 when page size and RX buffer size are both 4096.

So this patch changes the hns3_page_order to return 1 when
RX buffer is greater than half of the page size and page size
is less the 8192, and dev_alloc_pages has already been used
to allocate the compound page for RX buffer.

This patch also changes hnae3_* to hns3_* for page order
and RX buffer size calculation because they are used in
hns3 module.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The misc interrupt is used to schedule the reset and mailbox
subtask, and service_task delayed_work is used to do periodic
management work each second.

This patch sets the above three subtask's affinity using the
misc interrupt' affinity.

Also this patch setups a affinity notify for misc interrupt to
allow user to change the above three subtask's affinity.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use delayed work instead of using timers to trigger the
hclge_serive.

Simplify the code with one less middle function and in order
to support misc irq affinity.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some times just see the eth interface have been down/up via
dmesg, but can not know why the eth down. So adds some debug
messages to identify the cause for this.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch modifies firmware version display format in
hclge(vf)_cmd_init() and hns3_get_drvinfo(). Also, adds
some optimizations for firmware version display format.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating memory, the GFP_KERNEL cannot be used during the
spin_lock period. This is because it may cause scheduling when holding
spin_lock. This patch changes GFP flag to GFP_ATOMIC in this case.

Fixes: dd74f815 ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: Nlipeng 00277521 <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, hclge_reset_err_handle() will assert a global reset
when the failing count is smaller than MAX_RESET_FAIL_CNT, which
will affect other running functions.

So this patch removes this upgrading, and uses re-scheduling reset
task to do it.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some cases, ops->get_reset_level may not be implemented, so we
should check whether it is NULL before calling get_reset_level.
Signed-off-by: NGuangbin Huang <huangguangbin@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hns3_set_channels() should check the resetting status firstly,
since the device will reinitialize when resetting. If the
reset has not completed, the hns3_set_channels() may access
invalid memory.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>