New gspca subdriver adding support for SN9C2028 dual-mode cameras.
Signed-off-by: NTheodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If you read the mail to Oliver Neukum on the linux-usb list, then you know
that I found a cure for the mysterious problem that the MR97310a CIF "type
1" cameras have been freezing up and refusing to stream if hooked up to a
machine with a UHCI controller.

Namely, the cure is that if the camera is an mr97310a CIF type 1 camera, you
have to send it 0xa0, 0x00. Somehow, this is a timing reset command, or
such. It un-blocks whatever was previously stopping the CIF type 1 cameras
from working on the UHCI-based machines.
Signed-off-by: NTheodore Kilgore <kilgota@auburn.edu>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The TDA8261 driver would crash when reading more than a byte as described.

ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
[ 8.430350] KNC1-2: MAC addr = 00:09:d6:65:2d:91
[ 8.610008] saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
[ 8.734457] stb0899_attach: Attaching STB0899
[ 8.768481] tda8261_attach: Attaching TDA8261 8PSK/QPSK tuner
[ 8.768485] DVB: registering adapter 2 frontend 0 (STB0899 Multistandard)...

Once I launch scan-s2:
scan-s2 -vvvv -a 2 -s 1 -l UNIVERSAL /usr/share/dvb/dvb-s/Hotbird-13.0E

I see the following via dmesg:

[ 435.040017] saa7146 (1) saa7146_i2c_writeout [irq]: timed out waiting for end of xfer
[ 435.778648] tda8261_get_bandwidth: Bandwidth=40000000
[ 435.781781] tda8261_get_bandwidth: Bandwidth=40000000
[ 435.783311] tda8261_set_state: Step size=1, Divider=1000, PG=0x793 (1939)
[ 435.783512] tda8261_set_state: Waiting to Phase LOCK
[ 435.810134] tda8261_get_status: Tuner Phase Locked
[ 435.810137] tda8261_set_state: Tuner Phase locked: status=1
[ 435.810139] tda8261_set_frequency: Frequency=1939000
[ 435.810141] tda8261_get_frequency: Frequency=7574
[ 435.830008] tda8261_get_bandwidth: Bandwidth=40000000
[ 436.402814] tda8261_get_bandwidth: Bandwidth=40000000
[ 436.405946] tda8261_get_bandwidth: Bandwidth=40000000
[ 436.407458] general protection fault: 0000 [#1] SMP
[ 436.407527] last sysfs file: /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
[ 436.407560] CPU 0
[ 436.407601] Modules linked in: tda8261 stb0899 dvb_pll mt352 lnbp21 budget_av saa7146_vv snd_hda_codec_realtek videodev stv0299 v4l1_compat coretemp snd_hda_intel v4l2_compat_ioctl32 i915 videobuf_dma_sg b2c2_flexcop_pci snd_hda_codec budget_ci videobuf_core b2c2_flexcop ir_common w83627ehf drm snd_hwdep cx24123 budget_core hwmon_vid snd_pcm cx24113 dvb_core iptable_filter snd_timer i2c_algo_bit ip_tables saa7146 s5h1420 snd ttpci_eeprom soundcore intel_agp video serio_raw pcspkr lp snd_page_alloc x_tables output parport pata_it8213 e1000e
[ 436.408757] Pid: 1410, comm: kdvb-ad-2-fe-0 Not tainted 2.6.31-14-server #48-Ubuntu C2SBC-Q
[ 436.408818] RIP: 0010:[<ffffffffa00241a1>] [<ffffffffa00241a1>] tda8261_set_state+0x51/0x250 [tda8261]
[ 436.408903] RSP: 0018:ffff88013649bc70 EFLAGS: 00010283
[ 436.408945] RAX: 00000000000f1748 RBX: ffff880138870680 RCX: 0000000000000018
[ 436.408990] RDX: ffff88013649bcd0 RSI: 0000000000000001 RDI: ffff880135273010
[ 436.409035] RBP: ffff88013649bcc0 R08: 0000000000000001 R09: 0000000000000002
[ 436.409081] R10: ffff88013649bc40 R11: 0000000055555556 R12: 00000000001d9638
[ 436.409126] R13: 38ffffffa0261568 R14: 0000000000000000 R15: ffff880135273010
[ 436.409172] FS: 0000000000000000(0000) GS:ffff880028022000(0000) knlGS:0000000000000000
[ 436.409232] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
[ 436.409274] CR2: 00007fff925e4cd8 CR3: 000000013642a000 CR4: 00000000000406f0
[ 436.409320] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 436.409365] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 436.409411] Process kdvb-ad-2-fe-0 (pid: 1410, threadinfo ffff88013649a000, task ffff88013658ad60)
[ 436.409473] Stack:
[ 436.409508] ffff880136ee2af1 00000000bcd5d166 ffff000200000068 0000000035273000
[ 436.409608] <0> 0000000000000001 ffff880135273000 ffffffffa0265260 00003473bc000000
[ 436.409758] <0> 0000000000000000 ffff88013a4e05e0 ffff88013649bd00 ffffffffa025f133
[ 436.409938] Call Trace:
[ 436.409978] [<ffffffffa025f133>] tda8261_set_frequency+0x23/0x70 [budget_av]
[ 436.410027] [<ffffffffa026ed09>] ? stb0899_i2c_gate_ctrl+0x49/0xf0 [stb0899]
[ 436.410074] [<ffffffffa026e259>] ? stb0899_write_reg+0x19/0x20 [stb0899]
[ 436.410121] [<ffffffffa02716e2>] stb0899_dvbs_algo+0x3a2/0x13c8 [stb0899]
[ 436.410170] [<ffffffff813cdd0d>] ? i2c_transfer+0xbd/0x100
[ 436.410215] [<ffffffffa026e13c>] ? stb0899_write_regs+0xac/0x1b0 [stb0899]
[ 436.410262] [<ffffffffa026f239>] stb0899_search+0x489/0x750 [stb0899]
[ 436.410308] [<ffffffff8107d153>] ? down_interruptible+0x33/0x60
[ 436.410360] [<ffffffffa00c34ec>] dvb_frontend_thread+0x57c/0x720 [dvb_core]
[ 436.410407] [<ffffffff81078620>] ? autoremove_wake_function+0x0/0x40
[ 436.410457] [<ffffffffa00c2f70>] ? dvb_frontend_thread+0x0/0x720 [dvb_core]
[ 436.410504] [<ffffffff81078236>] kthread+0xa6/0xb0
[ 436.410547] [<ffffffff810130aa>] child_rip+0xa/0x20
[ 436.410589] [<ffffffff81078190>] ? kthread+0x0/0xb0
[ 436.410631] [<ffffffff810130a0>] ? child_rip+0x0/0x20
[ 436.410672] Code: 00 03 00 00 4c 8b 6b 10 c7 45 cc 00 00 00 00 0f 84 e8 01 00 00 44 8b 22 41 8d 84 24 10 81 f1 ff 3d 80 4f 12 00 0f 87 af 01 00 00 <41> 8b 75 04 31 d2 48 c7 c7 d8 46 02 a0 89 f0 8b 0c 85 f0 45 02
[ 436.411950] RIP [<ffffffffa00241a1>] tda8261_set_state+0x51/0x250 [tda8261]
[ 436.412015] RSP <ffff88013649bc70>
[ 436.412064] ---[ end trace c1d7ae4d9e05c51b ]---
Signed-off-by: NArvo Järve <arvo@softshark.ee>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add parameters adc1_range, adc2_range and tuner_bbgain to the config struct.
Defaults: adc1_range = adc2_range = 2Vpp, tuner_bbgain = 10db
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Exit stv090x_algo() if the tuner did not lock. This might happen due to
missing signal or invalid/incomplete tuning parameters.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The I2C gate must also be disabled, if a tuner command failed.
Otherwise the tuner mutex would be locked forever.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When mclk is not 0 then it will never be set to the correct value and
the Demodulator will not work.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This gives the STV090x and improved clock signal (rectangle instead of sine).
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Using clk_div member of stv6110x_config structure the tuner's clock
output divider can be configured. It is set in stv6110x_attach.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is needed when clock input is driven from tuner and an output
divider different from 1 is used.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Before there was used a static register map that could lead to issues
when there are are multiple adapters with the STV6110(A).
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The function stv6110x_write_regs is used to write several registers at once.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This could be useful for p.e. Common Interface applications where data rate is limited.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With this change it is possible to have the same I2C address for both tuners.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As the STV0900 features two demodulation paths in one chip there is
some information used by both instances of the driver when used in
dual mode. This information is now shared in an internal structure
referenced by I2C adapter and address.

Do initialisation of the demodulator only once when used in dual mode.
Moved global mutex demod_lock to internal structure.
Moved dev_ver and mclk to internal structure.
Removed unused tuner_refclk from stv090x_state.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In automatic S/S2 detection mode, locking of a DVB-S transponder could
fail when coming from a DVB-S2 transponder. This change fixes the issue
by first disabling DVB-S and DVB-S2 mode before enabling it again.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."

In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone  = stv0900_set_tone

redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The two sensors ov772x and ov965x have too much differences.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of

drivers/media/dvb/bt8xx/bt878.c

Please have a look at the small patch and either pull it through
your tree, or please ack' it so Jiri can pull it through the trivial
tree.

Patch against linux-next-tree, 22. Dez 08:38:18 CET 2009
but also present in linus tree.
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

And a little code refactoring/neatening around the removals

Reduces object size a little bit:

new:
$ size drivers/media/dvb/frontends/si21xx.o
   text	   data	    bss	    dec	    hex	filename
   8984	     56	   1816	  10856	   2a68	drivers/media/dvb/frontends/si21xx.o
old:
$ size drivers/media/dvb/frontends/si21xx.o
   text	   data	    bss	    dec	    hex	filename
   9084	     56	   1792	  10932	   2ab4	drivers/media/dvb/frontends/si21xx.o
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Stanse found a potential null dereference in cx18_dvb_start_feed
and cx18_dvb_stop_feed. There is a check for stream being NULL,
but it is dereferenced earlier. Move the dereference after the
check.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Reviewed-by: NAndy Walls <awalls@radix.net>
Acked-by: NAndy Walls <awalls@radix.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Free ir_dev before exit.
Found by cppcheck.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Stanse found an unreachable statement in zl10039_attach. There is
a `break' followed by `goto error'. Remove that break, so that it
can handle the error.

Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Stanse found a memory leak in tuner_probe. It is not freed/assigned
on all paths. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Stanse found a memory leak in smscore_gpio_configure. buffer is not
freed/assigned on all paths. Fix that.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The return of saa7164_i2caddr_to_reglen() was not tested.

Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

this patch fixes a memory leak which occurs when an em28xx card with DVB
extension is unplugged or its DVB extension driver is unloaded. In
dvb_fini(), dev->dvb must be freed before being set to NULL, as is done
in dvb_init() in case of error.
Note that this bug is also present in the latest stable kernel release.
Signed-off-by: NFrancesco Lavra <francescolavra@interfree.it>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the %pM kernel extension to display the MAC address.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the declaration of the sysfs attributes for IR's, which
must be a NULL-terminated array of struct attribute *.
Without this patch, my machine crashes when inserting a DVB card.
Signed-off-by: NFrancesco Lavra <francescolavra@interfree.it>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I was initially concerned about the weird array index (the 2 bumps
into the next row of the array).  Matthias Schwarzott look at the
datasheet and it turns out it should be zl10036_init_tab[1][0] |= 0x01;
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Test the just-allocated value for NULL rather than some other value.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier f;
@@

f(...) { <+... return NULL; ...+> }

@@
expression *x;
expression y;
identifier r.f;
statement S;
@@

x = f(...);
(
if ((x) == NULL) S
|
if (
-   y
+   x
       == NULL)
 S
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If there is ever going to be a FireDTV or FloppyDTV firmware which does
not provide a minimal ASCII textual descriptor for Model_Id --- or if
the descriptor is provided indirectly in a descriptor directory ---
the ieee1394 variant of the device probe of firedtv would dereference a
NULL pointer.  The firewire variant of firedtv's device probe is not
affected.

The fix makes sure that such an unexpected firmware is safely recognized
by fdtv_alloc as an unknown firmware.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If the NULL test is necessary, then the dereference should be moved below
the NULL test.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@

- T i = E->fld;
+ T i;
  ... when != E
      when != i
  if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>