Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 02 8月, 2013 2 次提交
  3. 01 8月, 2013 5 次提交
    • S
      [media] media: lirc: Allow lirc dev to talk to rc device · ca7a722d
      由 Srinivas Kandagatla 提交于 
      The use case is simple, if any rc device has allowed protocols =
RC_TYPE_LIRC and map_name = RC_MAP_LIRC set, the driver open will be never
called. The reason for this is, all of the key maps except lirc have some
KEYS in there map, so during rc_register_device process these keys are
matched against the input drivers and open is performed, so for the case
of RC_MAP_EMPTY, a vt/keyboard is matched and the driver open is
performed.
In case of lirc, there is no match and result is that there is no open
performed, however the lirc-dev will go ahead and create a /dev/lirc0
node. Now when lircd/mode2 opens this device, no data is available
because the driver was never opened.
Other case pointed by Sean Young, As rc device gets opened via the
input interface. If the input device is never opened (e.g. embedded with
no console) then the rc open is never called and lirc will not work
either. So that's another case.
lirc_dev seems to have no link with actual rc device w.r.t open/close.
This patch adds rc_dev pointer to lirc_driver structure for cases like
this, so that it can do the open/close of the real driver in accordance
to lircd/mode2 open/close.
Without this patch its impossible to open a rc device which has
RC_TYPE_LIRC ad RC_MAP_LIRC set.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
      ca7a722d
    • S
      [media] media: rc: Add rc_open/close and use count to rc_dev · 8b2ff320
      由 Srinivas Kandagatla 提交于 
      This patch adds user count to rc_dev structure, the reason to add this
new member is to allow other code like lirc to open rc device directly.
In the existing code, rc device is only opened by input subsystem which
works ok if we have any input drivers to match. But in case like lirc
where there will be no input driver, rc device will be never opened.
Having this user count variable will be usefull to allow rc device to be
opened from code other than rc-main.
This patch also adds rc_open and rc_close functions for other drivers
like lirc to open and close rc devices. This functions safely increment
and decrement the user count. Other driver wanting to open rc device
should call rc_open and rc_close, rather than directly modifying the
rc_dev structure.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
      8b2ff320
    • P
      [media] coda: add CODA7541 decoding support · 918c66fd
      由 Philipp Zabel 提交于 
      This patch enables decoding of h.264 and mpeg4 streams on CODA7541.
Queued output buffers are immediately copied into the bitstream
ringbuffer. A device_run can be scheduled whenever there is either
enough compressed bitstream data, or the CODA is in stream end mode.
Each successful device_run, data is read from the bitstream ringbuffer
and a frame is decoded into a free internal framebuffer. Depending on
reordering, a possibly previously decoded frame is marked as display
frame, and at the same time the display frame from the previous run
is copied out into a capture buffer by the rotator hardware.
The dequeued capture buffers are counted to send the EOS signal to
userspace with the last frame. When userspace sends the decoder stop
command or enqueues an empty output buffer, the stream end flag is
set to allow decoding the remaining frames in the bitstream
ringbuffer.
The enum_fmt/try_fmt functions return fixed capture buffer sizes
while the output queue is streaming, to allow better autonegotiation
in userspace.
A per-context buffer mutex is used to lock the picture run against
buffer dequeueing: if a job gets queued, then streamoff dequeues
the last buffer, and then device_run is called, bail out. For that
the interrupt handler has to be threaded.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
      918c66fd
    • P
      [media] coda: split encoder specific parts out of device_run and irq_handler · 477c1cfe
      由 Philipp Zabel 提交于 
      Add coda_prepare_encode() and coda_finish_encode() functions. They are called
from coda_device_run() and coda_irq_handler(), respectively, before and after
the hardware picture run. This should make the following decoder support patch
easier to read, which will add the coda_prepare/finish_decode() equivalents.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
      477c1cfe
    • P
      [media] coda: dynamic IRAM setup for decoder · 8358e76c
      由 Philipp Zabel 提交于 
      This sets up IRAM areas used as temporary memory for the different
hardware units depending on the frame size.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
      8358e76c
  5. 31 7月, 2013 11 次提交
  7. 29 7月, 2013 4 次提交
  9. 27 7月, 2013 18 次提交