This reverts commit 624ca9c3.

This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:

	has-inverted-stacr-oc
	has-new-stacr-staopc

What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.

Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stefano Brivio says:

====================
Fix slab out-of-bounds on insufficient headroom for IPv6 packets

Patch 1/2 fixes a slab out-of-bounds occurring with short SCTP packets over
IPv4 over L2TP over IPv6 on a configuration with relatively low HEADER_MAX.

Patch 2/2 makes sure we avoid writing before the allocated buffer in
neigh_hh_output() in case the headroom is enough for the unaligned hardware
header size, but not enough for the aligned one, and that we warn if we hit
this condition.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While skb_push() makes the kernel panic if the skb headroom is less than
the unaligned hardware header size, it will proceed normally in case we
copy more than that because of alignment, and we'll silently corrupt
adjacent slabs.

In the case fixed by the previous patch,
"ipv6: Check available headroom in ip6_xmit() even without options", we
end up in neigh_hh_output() with 14 bytes headroom, 14 bytes hardware
header and write 16 bytes, starting 2 bytes before the allocated buffer.

Always check we're not writing before skb->head and, if the headroom is
not enough, warn and drop the packet.

v2:
 - instead of panicking with BUG_ON(), WARN_ON_ONCE() and drop the packet
   (Eric Dumazet)
 - if we avoid the panic, though, we need to explicitly check the headroom
   before the memcpy(), otherwise we'll have corrupted slabs on a running
   kernel, after we warn
 - use __skb_push() instead of skb_push(), as the headroom check is
   already implemented here explicitly (Eric Dumazet)
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if we send an IPv6 packet without options, MAX_HEADER might not be
enough to account for the additional headroom required by alignment of
hardware headers.

On a configuration without HYPERV_NET, WLAN, AX25, and with IPV6_TUNNEL,
sending short SCTP packets over IPv4 over L2TP over IPv6, we start with
100 bytes of allocated headroom in sctp_packet_transmit(), end up with 54
bytes after l2tp_xmit_skb(), and 14 bytes in ip6_finish_output2().

Those would be enough to append our 14 bytes header, but we're going to
align that to 16 bytes, and write 2 bytes out of the allocated slab in
neigh_hh_output().

KASan says:

[  264.967848] ==================================================================
[  264.967861] BUG: KASAN: slab-out-of-bounds in ip6_finish_output2+0x1aec/0x1c70
[  264.967866] Write of size 16 at addr 000000006af1c7fe by task netperf/6201
[  264.967870]
[  264.967876] CPU: 0 PID: 6201 Comm: netperf Not tainted 4.20.0-rc4+ #1
[  264.967881] Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
[  264.967887] Call Trace:
[  264.967896] ([<00000000001347d6>] show_stack+0x56/0xa0)
[  264.967903]  [<00000000017e379c>] dump_stack+0x23c/0x290
[  264.967912]  [<00000000007bc594>] print_address_description+0xf4/0x290
[  264.967919]  [<00000000007bc8fc>] kasan_report+0x13c/0x240
[  264.967927]  [<000000000162f5e4>] ip6_finish_output2+0x1aec/0x1c70
[  264.967935]  [<000000000163f890>] ip6_finish_output+0x430/0x7f0
[  264.967943]  [<000000000163fe44>] ip6_output+0x1f4/0x580
[  264.967953]  [<000000000163882a>] ip6_xmit+0xfea/0x1ce8
[  264.967963]  [<00000000017396e2>] inet6_csk_xmit+0x282/0x3f8
[  264.968033]  [<000003ff805fb0ba>] l2tp_xmit_skb+0xe02/0x13e0 [l2tp_core]
[  264.968037]  [<000003ff80631192>] l2tp_eth_dev_xmit+0xda/0x150 [l2tp_eth]
[  264.968041]  [<0000000001220020>] dev_hard_start_xmit+0x268/0x928
[  264.968069]  [<0000000001330e8e>] sch_direct_xmit+0x7ae/0x1350
[  264.968071]  [<000000000122359c>] __dev_queue_xmit+0x2b7c/0x3478
[  264.968075]  [<00000000013d2862>] ip_finish_output2+0xce2/0x11a0
[  264.968078]  [<00000000013d9b14>] ip_finish_output+0x56c/0x8c8
[  264.968081]  [<00000000013ddd1e>] ip_output+0x226/0x4c0
[  264.968083]  [<00000000013dbd6c>] __ip_queue_xmit+0x894/0x1938
[  264.968100]  [<000003ff80bc3a5c>] sctp_packet_transmit+0x29d4/0x3648 [sctp]
[  264.968116]  [<000003ff80b7bf68>] sctp_outq_flush_ctrl.constprop.5+0x8d0/0xe50 [sctp]
[  264.968131]  [<000003ff80b7c716>] sctp_outq_flush+0x22e/0x7d8 [sctp]
[  264.968146]  [<000003ff80b35c68>] sctp_cmd_interpreter.isra.16+0x530/0x6800 [sctp]
[  264.968161]  [<000003ff80b3410a>] sctp_do_sm+0x222/0x648 [sctp]
[  264.968177]  [<000003ff80bbddac>] sctp_primitive_ASSOCIATE+0xbc/0xf8 [sctp]
[  264.968192]  [<000003ff80b93328>] __sctp_connect+0x830/0xc20 [sctp]
[  264.968208]  [<000003ff80bb11ce>] sctp_inet_connect+0x2e6/0x378 [sctp]
[  264.968212]  [<0000000001197942>] __sys_connect+0x21a/0x450
[  264.968215]  [<000000000119aff8>] sys_socketcall+0x3d0/0xb08
[  264.968218]  [<000000000184ea7a>] system_call+0x2a2/0x2c0

[...]

Just like ip_finish_output2() does for IPv4, check that we have enough
headroom in ip6_xmit(), and reallocate it if we don't.

This issue is older than git history.
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_tso_should_defer() can return true in three different cases :

 1) We are cwnd-limited
 2) We are rwnd-limited
 3) We are application limited.

Neal pointed out that my recent fix went too far, since
it assumed that if we were not in 1) case, we must be rwnd-limited

Fix this by properly populating the is_cwnd_limited and
is_rwnd_limited booleans.

After this change, we can finally move the silly check for FIN
flag only for the application-limited case.

The same move for EOR bit will be handled in net-next,
since commit 1c09f7d0 ("tcp: do not try to defer skbs
with eor mark (MSG_EOR)") is scheduled for linux-4.21

Tested by running 200 concurrent netperf -t TCP_RR -- -r 60000,100
and checking none of them was rwnd_limited in the chrono_stat
output from "ss -ti" command.

Fixes: 41727549 ("tcp: Do not underestimate rwnd_limited")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Suggested-by: NNeal Cardwell <ncardwell@google.com>
Reviewed-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In 'seg6_output', stack variable 'struct flowi6 fl6' was missing
initialization.

Fixes: 6c8702c6 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various fixes

Patches #1 and #2 fix two VxLAN related issues. The first patch removes
warnings that can currently be triggered from user space. Second patch
avoids leaking a FID in an error path.

Patch #3 fixes a too strict check that causes certain host routes not to
be promoted to perform GRE decapsulation in hardware.

Last patch avoids a use-after-free when deleting a VLAN device via an
ioctl when it is enslaved to a bridge. I have a patchset for net-next
that reworks this code and makes the driver more robust.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.

The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.

Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.

Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.

Fixes: 4607f6d2 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: NNir Dotan <nird@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().

Drop the reference when this unlikely error is hit.

Fixes: 1c30d183 ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.

Fix by removing these warnings for now.

Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.

Fixes: 6e6030bd ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The *_frag_reasm() functions are susceptible to miscalculating the byte
count of packet fragments in case the truesize of a head buffer changes.
The truesize member may be changed by the call to skb_unclone(), leaving
the fragment memory limit counter unbalanced even if all fragments are
processed. This miscalculation goes unnoticed as long as the network
namespace which holds the counter is not destroyed.

Should an attempt be made to destroy a network namespace that holds an
unbalanced fragment memory limit counter the cleanup of the namespace
never finishes. The thread handling the cleanup gets stuck in
inet_frags_exit_net() waiting for the percpu counter to reach zero. The
thread is usually in running state with a stacktrace similar to:

 PID: 1073   TASK: ffff880626711440  CPU: 1   COMMAND: "kworker/u48:4"
  #5 [ffff880621563d48] _raw_spin_lock at ffffffff815f5480
  #6 [ffff880621563d48] inet_evict_bucket at ffffffff8158020b
  #7 [ffff880621563d80] inet_frags_exit_net at ffffffff8158051c
  #8 [ffff880621563db0] ops_exit_list at ffffffff814f5856
  #9 [ffff880621563dd8] cleanup_net at ffffffff814f67c0
 #10 [ffff880621563e38] process_one_work at ffffffff81096f14

It is not possible to create new network namespaces, and processes
that call unshare() end up being stuck in uninterruptible sleep state
waiting to acquire the net_mutex.

The bug was observed in the IPv6 netfilter code by Per Sundstrom.
I thank him for his analysis of the problem. The parts of this patch
that apply to IPv4 and IPv6 fragment reassembly are preemptive measures.
Signed-off-by: NJiri Wiesner <jwiesner@suse.com>
Reported-by: NPer Sundstrom <per.sundstrom@redqube.se>
Acked-by: NPeter Oskolkov <posk@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If for some reason an association's fragmentation point is zero,
sctp_datamsg_from_user will try to endlessly try to divide a message
into zero-sized chunks. This eventually causes kernel panic due to
running out of memory.

Although this situation is quite unlikely, it has occurred before as
reported. I propose to add this simple last-ditch sanity check due to
the severity of the potential consequences.
Signed-off-by: NJakub Audykowicz <jakub.audykowicz@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP loss probe timer may fire when the retranmission queue is empty but
has a non-zero tp->packets_out counter. tcp_send_loss_probe will call
tcp_rearm_rto which triggers NULL pointer reference by fetching the
retranmission queue head in its sub-routines.

Add a more detailed warning to help catch the root cause of the inflight
accounting inconsistency.
Reported-by: NRafael Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If available rwnd is too small, tcp_tso_should_defer()
can decide it is worth waiting before splitting a TSO packet.

This really means we are rwnd limited.

Fixes: 5615f886 ("tcp: instrument how long TCP is limited by receive window")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2018-12-05

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) fix bpf uapi pointers for 32-bit architectures, from Daniel.

2) improve verifer ability to handle progs with a lot of branches, from Alexei.

3) strict btf checks, from Yonghong.

4) bpf_sk_lookup api cleanup, from Joe.

5) other misc fixes
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

list_del() leaves the skb->next pointer poisoned, which can then lead to
 a crash in e.g. OVS forwarding.  For example, setting up an OVS VXLAN
 forwarding bridge on sfc as per:

========
$ ovs-vsctl show
5dfd9c47-f04b-4aaa-aa96-4fbb0a522a30
    Bridge "br0"
        Port "br0"
            Interface "br0"
                type: internal
        Port "enp6s0f0"
            Interface "enp6s0f0"
        Port "vxlan0"
            Interface "vxlan0"
                type: vxlan
                options: {key="1", local_ip="10.0.0.5", remote_ip="10.0.0.4"}
    ovs_version: "2.5.0"
========
(where 10.0.0.5 is an address on enp6s0f1)
and sending traffic across it will lead to the following panic:
========
general protection fault: 0000 [#1] SMP PTI
CPU: 5 PID: 0 Comm: swapper/5 Not tainted 4.20.0-rc3-ehc+ #701
Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013
RIP: 0010:dev_hard_start_xmit+0x38/0x200
Code: 53 48 89 fb 48 83 ec 20 48 85 ff 48 89 54 24 08 48 89 4c 24 18 0f 84 ab 01 00 00 48 8d 86 90 00 00 00 48 89 f5 48 89 44 24 10 <4c> 8b 33 48 c7 03 00 00 00 00 48 8b 05 c7 d1 b3 00 4d 85 f6 0f 95
RSP: 0018:ffff888627b437e0 EFLAGS: 00010202
RAX: 0000000000000000 RBX: dead000000000100 RCX: ffff88862279c000
RDX: ffff888614a342c0 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff888618a88000 R08: 0000000000000001 R09: 00000000000003e8
R10: 0000000000000000 R11: ffff888614a34140 R12: 0000000000000000
R13: 0000000000000062 R14: dead000000000100 R15: ffff888616430000
FS:  0000000000000000(0000) GS:ffff888627b40000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6d2bc6d000 CR3: 000000000200a000 CR4: 00000000000006e0
Call Trace:
 <IRQ>
 __dev_queue_xmit+0x623/0x870
 ? masked_flow_lookup+0xf7/0x220 [openvswitch]
 ? ep_poll_callback+0x101/0x310
 do_execute_actions+0xaba/0xaf0 [openvswitch]
 ? __wake_up_common+0x8a/0x150
 ? __wake_up_common_lock+0x87/0xc0
 ? queue_userspace_packet+0x31c/0x5b0 [openvswitch]
 ovs_execute_actions+0x47/0x120 [openvswitch]
 ovs_dp_process_packet+0x7d/0x110 [openvswitch]
 ovs_vport_receive+0x6e/0xd0 [openvswitch]
 ? dst_alloc+0x64/0x90
 ? rt_dst_alloc+0x50/0xd0
 ? ip_route_input_slow+0x19a/0x9a0
 ? __udp_enqueue_schedule_skb+0x198/0x1b0
 ? __udp4_lib_rcv+0x856/0xa30
 ? __udp4_lib_rcv+0x856/0xa30
 ? cpumask_next_and+0x19/0x20
 ? find_busiest_group+0x12d/0xcd0
 netdev_frame_hook+0xce/0x150 [openvswitch]
 __netif_receive_skb_core+0x205/0xae0
 __netif_receive_skb_list_core+0x11e/0x220
 netif_receive_skb_list+0x203/0x460
 ? __efx_rx_packet+0x335/0x5e0 [sfc]
 efx_poll+0x182/0x320 [sfc]
 net_rx_action+0x294/0x3c0
 __do_softirq+0xca/0x297
 irq_exit+0xa6/0xb0
 do_IRQ+0x54/0xd0
 common_interrupt+0xf/0xf
 </IRQ>
========
So, in all listified-receive handling, instead pull skbs off the lists with
 skb_list_del_init().

Fixes: 9af86f93 ("net: core: fix use-after-free in __netif_receive_skb_list_core")
Fixes: 7da517a3 ("net: core: Another step of skb receive list processing")
Fixes: a4ca8b7d ("net: ipv4: fix drop handling in ip_list_rcv() and ip_list_rcv_finish()")
Fixes: d8269e2c ("net: ipv6: listify ipv6_rcv() and ip6_rcv_finish()")
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg:

====================
As it's been a while, we have various fixes for
 * hwsim
 * AP mode (client powersave related)
 * CSA/FTM interaction
 * a busy loop in IE handling
 * and similar
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function was modified to support the information element extension
case (WLAN_EID_EXTENSION) in a manner that would result in an infinite
loop when going through set of IEs that include WLAN_EID_RIC_DATA and
contain an IE that is in the after_ric array. The only place where this
can currently happen is in mac80211 ieee80211_send_assoc() where
ieee80211_ie_split_ric() is called with after_ric[].

This can be triggered by valid data from user space nl80211
association/connect request (i.e., requiring GENL_UNS_ADMIN_PERM). The
only known application having an option to include WLAN_EID_RIC_DATA in
these requests is wpa_supplicant and it had a bug that prevented this
specific contents from being used (and because of that, not triggering
this kernel bug in an automated test case ap_ft_ric) and now that this
bug is fixed, it has a workaround to avoid this kernel issue.
WLAN_EID_RIC_DATA is currently used only for testing purposes, so this
does not cause significant harm for production use cases.

Fixes: 2512b1b1 ("mac80211: extend ieee80211_ie_split to support EXTENSION")
Cc: stable@vger.kernel.org
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

NullFunc packets should never be duplicate just like
QoS-NullFunc packets.

We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449

CC: <stable@vger.kernel.org>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.

Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.

Fixes: f027c2ac ("mac80211: add ieee80211_tx_status_noskb")
Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.

Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.

Catch the uninitialized PHY mode case, and allow 10G rates.

Fixes: d97c9f4a ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.

This patch removes the unwarranted call to of_node_put().

Fixes: 414fd46e ("fsl/fman: Add FMan support")
Signed-off-by: NNicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kmsan was able to trigger a kernel-infoleak using a gre device [1]

nlmsg_populate_fdb_fill() has a hard coded assumption
that dev->addr_len is ETH_ALEN, as normally guaranteed
for ARPHRD_ETHER devices.

A similar issue was fixed recently in commit da715775
("rtnetlink: Disallow FDB configuration for non-Ethernet device")

[1]
BUG: KMSAN: kernel-infoleak in copyout lib/iov_iter.c:143 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x4c0/0x2700 lib/iov_iter.c:576
CPU: 0 PID: 6697 Comm: syz-executor310 Not tainted 4.20.0-rc3+ #95
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x32d/0x480 lib/dump_stack.c:113
 kmsan_report+0x12c/0x290 mm/kmsan/kmsan.c:683
 kmsan_internal_check_memory+0x32a/0xa50 mm/kmsan/kmsan.c:743
 kmsan_copy_to_user+0x78/0xd0 mm/kmsan/kmsan_hooks.c:634
 copyout lib/iov_iter.c:143 [inline]
 _copy_to_iter+0x4c0/0x2700 lib/iov_iter.c:576
 copy_to_iter include/linux/uio.h:143 [inline]
 skb_copy_datagram_iter+0x4e2/0x1070 net/core/datagram.c:431
 skb_copy_datagram_msg include/linux/skbuff.h:3316 [inline]
 netlink_recvmsg+0x6f9/0x19d0 net/netlink/af_netlink.c:1975
 sock_recvmsg_nosec net/socket.c:794 [inline]
 sock_recvmsg+0x1d1/0x230 net/socket.c:801
 ___sys_recvmsg+0x444/0xae0 net/socket.c:2278
 __sys_recvmsg net/socket.c:2327 [inline]
 __do_sys_recvmsg net/socket.c:2337 [inline]
 __se_sys_recvmsg+0x2fa/0x450 net/socket.c:2334
 __x64_sys_recvmsg+0x4a/0x70 net/socket.c:2334
 do_syscall_64+0xcf/0x110 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x441119
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db 0a fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fffc7f008a8 EFLAGS: 00000207 ORIG_RAX: 000000000000002f
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000441119
RDX: 0000000000000040 RSI: 00000000200005c0 RDI: 0000000000000003
RBP: 00000000006cc018 R08: 0000000000000100 R09: 0000000000000100
R10: 0000000000000100 R11: 0000000000000207 R12: 0000000000402080
R13: 0000000000402110 R14: 0000000000000000 R15: 0000000000000000

Uninit was stored to memory at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:246 [inline]
 kmsan_save_stack mm/kmsan/kmsan.c:261 [inline]
 kmsan_internal_chain_origin+0x13d/0x240 mm/kmsan/kmsan.c:469
 kmsan_memcpy_memmove_metadata+0x1a9/0xf70 mm/kmsan/kmsan.c:344
 kmsan_memcpy_metadata+0xb/0x10 mm/kmsan/kmsan.c:362
 __msan_memcpy+0x61/0x70 mm/kmsan/kmsan_instr.c:162
 __nla_put lib/nlattr.c:744 [inline]
 nla_put+0x20a/0x2d0 lib/nlattr.c:802
 nlmsg_populate_fdb_fill+0x444/0x810 net/core/rtnetlink.c:3466
 nlmsg_populate_fdb net/core/rtnetlink.c:3775 [inline]
 ndo_dflt_fdb_dump+0x73a/0x960 net/core/rtnetlink.c:3807
 rtnl_fdb_dump+0x1318/0x1cb0 net/core/rtnetlink.c:3979
 netlink_dump+0xc79/0x1c90 net/netlink/af_netlink.c:2244
 __netlink_dump_start+0x10c4/0x11d0 net/netlink/af_netlink.c:2352
 netlink_dump_start include/linux/netlink.h:216 [inline]
 rtnetlink_rcv_msg+0x141b/0x1540 net/core/rtnetlink.c:4910
 netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2477
 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4965
 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
 netlink_unicast+0x1699/0x1740 net/netlink/af_netlink.c:1336
 netlink_sendmsg+0x13c7/0x1440 net/netlink/af_netlink.c:1917
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 ___sys_sendmsg+0xe3b/0x1240 net/socket.c:2116
 __sys_sendmsg net/socket.c:2154 [inline]
 __do_sys_sendmsg net/socket.c:2163 [inline]
 __se_sys_sendmsg+0x305/0x460 net/socket.c:2161
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161
 do_syscall_64+0xcf/0x110 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:246 [inline]
 kmsan_internal_poison_shadow+0x6d/0x130 mm/kmsan/kmsan.c:170
 kmsan_kmalloc+0xa1/0x100 mm/kmsan/kmsan_hooks.c:186
 __kmalloc+0x14c/0x4d0 mm/slub.c:3825
 kmalloc include/linux/slab.h:551 [inline]
 __hw_addr_create_ex net/core/dev_addr_lists.c:34 [inline]
 __hw_addr_add_ex net/core/dev_addr_lists.c:80 [inline]
 __dev_mc_add+0x357/0x8a0 net/core/dev_addr_lists.c:670
 dev_mc_add+0x6d/0x80 net/core/dev_addr_lists.c:687
 ip_mc_filter_add net/ipv4/igmp.c:1128 [inline]
 igmp_group_added+0x4d4/0xb80 net/ipv4/igmp.c:1311
 __ip_mc_inc_group+0xea9/0xf70 net/ipv4/igmp.c:1444
 ip_mc_inc_group net/ipv4/igmp.c:1453 [inline]
 ip_mc_up+0x1c3/0x400 net/ipv4/igmp.c:1775
 inetdev_event+0x1d03/0x1d80 net/ipv4/devinet.c:1522
 notifier_call_chain kernel/notifier.c:93 [inline]
 __raw_notifier_call_chain kernel/notifier.c:394 [inline]
 raw_notifier_call_chain+0x13d/0x240 kernel/notifier.c:401
 __dev_notify_flags+0x3da/0x860 net/core/dev.c:1733
 dev_change_flags+0x1ac/0x230 net/core/dev.c:7569
 do_setlink+0x165f/0x5ea0 net/core/rtnetlink.c:2492
 rtnl_newlink+0x2ad7/0x35a0 net/core/rtnetlink.c:3111
 rtnetlink_rcv_msg+0x1148/0x1540 net/core/rtnetlink.c:4947
 netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2477
 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:4965
 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
 netlink_unicast+0x1699/0x1740 net/netlink/af_netlink.c:1336
 netlink_sendmsg+0x13c7/0x1440 net/netlink/af_netlink.c:1917
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg net/socket.c:631 [inline]
 ___sys_sendmsg+0xe3b/0x1240 net/socket.c:2116
 __sys_sendmsg net/socket.c:2154 [inline]
 __do_sys_sendmsg net/socket.c:2163 [inline]
 __se_sys_sendmsg+0x305/0x460 net/socket.c:2161
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161
 do_syscall_64+0xcf/0x110 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x63/0xe7

Bytes 36-37 of 105 are uninitialized
Memory access of size 105 starts at ffff88819686c000
Data copied to user address 0000000020000380

Fixes: d83b0603 ("net: add fdb generic dump routine")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts:

ef1b5bf5 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b8 ("net: phy: micrel: add toggling phy reset if PHY is not  attached")

Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
Three patches to improve verifier ability to handle pathological bpf
programs with a lot of branches:

- make sure prog_load syscall can be aborted
- improve branch taken analysis
- introduce per-insn complexity limit for unprivileged programs
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

malicious bpf program may try to force the verifier to remember
a lot of distinct verifier states.
Put a limit to number of per-insn 'struct bpf_verifier_state'.
Note that hitting the limit doesn't reject the program.
It potentially makes the verifier do more steps to analyze the program.
It means that malicious programs will hit BPF_COMPLEXITY_LIMIT_INSNS sooner
instead of spending cpu time walking long link list.

The limit of BPF_COMPLEXITY_LIMIT_STATES==64 affects cilium progs
with slight increase in number of "steps" it takes to successfully verify
the programs:
                       before    after
bpf_lb-DLB_L3.o         1940      1940
bpf_lb-DLB_L4.o         3089      3089
bpf_lb-DUNKNOWN.o       1065      1065
bpf_lxc-DDROP_ALL.o     28052  |  28162
bpf_lxc-DUNKNOWN.o      35487  |  35541
bpf_netdev.o            10864     10864
bpf_overlay.o           6643      6643
bpf_lcx_jit.o           38437     38437

But it also makes malicious program to be rejected in 0.4 seconds vs 6.5
Hence apply this limit to unprivileged programs only.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

pathological bpf programs may try to force verifier to explode in
the number of branch states:
  20: (d5) if r1 s<= 0x24000028 goto pc+0
  21: (b5) if r0 <= 0xe1fa20 goto pc+2
  22: (d5) if r1 s<= 0x7e goto pc+0
  23: (b5) if r0 <= 0xe880e000 goto pc+0
  24: (c5) if r0 s< 0x2100ecf4 goto pc+0
  25: (d5) if r1 s<= 0xe880e000 goto pc+1
  26: (c5) if r0 s< 0xf4041810 goto pc+0
  27: (d5) if r1 s<= 0x1e007e goto pc+0
  28: (b5) if r0 <= 0xe86be000 goto pc+0
  29: (07) r0 += 16614
  30: (c5) if r0 s< 0x6d0020da goto pc+0
  31: (35) if r0 >= 0x2100ecf4 goto pc+0

Teach verifier to recognize always taken and always not taken branches.
This analysis is already done for == and != comparison.
Expand it to all other branches.

It also helps real bpf programs to be verified faster:
                       before  after
bpf_lb-DLB_L3.o         2003    1940
bpf_lb-DLB_L4.o         3173    3089
bpf_lb-DUNKNOWN.o       1080    1065
bpf_lxc-DDROP_ALL.o     29584   28052
bpf_lxc-DUNKNOWN.o      36916   35487
bpf_netdev.o            11188   10864
bpf_overlay.o           6679    6643
bpf_lcx_jit.o           39555   38437
Reported-by: NAnatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Malicious user space may try to force the verifier to use as much cpu
time and memory as possible. Hence check for pending signals
while verifying the program.
Note that suspend of sys_bpf(PROG_LOAD) syscall will lead to EAGAIN,
since the kernel has to release the resources used for program verification.
Reported-by: NAnatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Tariq Toukan says:

====================
mlx4 fixes for 4.20-rc

This patchset includes small fixes for the mlx4_en driver.

First patch by Eran fixes the value used to init the netdevice's
min_mtu field.
Please queue it to -stable >= v4.10.

Second patch by Saeed adds missing Kconfig build dependencies.

Series generated against net commit:
35b827b6 tun: forbid iface creation with rtnl ops
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.

This fixes the following build break:

drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIC driver minimal MTU size shall be set to ETH_MIN_MTU, as defined in
the RFC791 and in the network stack. Remove old mlx4_en only define for
it, which was set to wrong value.

Fixes: b80f71f5 ("ethernet/mellanox: use core min/max MTU checking")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_napi_add() could report an error like this below due to it allows
to pass a format string for wildcarding before calling
dev_get_valid_name(),

"netif_napi_add() called with weight 256 on device eth%d"

For example, hns_enet_drv module does this.

hns_nic_try_get_ae
  hns_nic_init_ring_data
    netif_napi_add
  register_netdev
    dev_get_valid_name

Hence, make it a bit more human-readable by using netdev_err_once()
instead.
Signed-off-by: NQian Cai <cai@gmx.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: NAnderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A MAC address must be unique among all the macvlan devices with the same
lower device. The only exception is the passthru [sic] mode,
which shares the lower device address.

When duplicate addresses are detected, EBUSY is returned when bringing
the interface up:

    # ip link add macvlan0 link eth0 type macvlan
    # read addr </sys/class/net/eth0/address
    # ip link set macvlan0 address $addr
    # ip link set macvlan0 up
    RTNETLINK answers: Device or resource busy

Use correct error code which is EADDRINUSE, and do the check also
earlier, on address change:

    # ip link set macvlan0 address $addr
    RTNETLINK answers: Address already in use
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In sctp_hash_transport/sctp_epaddr_lookup_transport, it dereferences
a transport's asoc under rcu_read_lock while asoc is freed not after
a grace period, which leads to a use-after-free panic.

This patch fixes it by calling kfree_rcu to make asoc be freed after
a grace period.

Note that only the asoc's memory is delayed to free in the patch, it
won't cause sk to linger longer.

Thanks Neil and Marcelo to make this clear.

Fixes: 7fda702f ("sctp: use new rhlist interface on sctp transport rhashtable")
Fixes: cd2b7087 ("sctp: check duplicate node before inserting a new transport")
Reported-by: syzbot+0b05d8aa7cb185107483@syzkaller.appspotmail.com
Reported-by: syzbot+aad231d51b1923158444@syzkaller.appspotmail.com
Suggested-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5681e20 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.

Fixes: a5681e20 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 78139c94 ("net: vhost: lock the vqs one by one") moved the vq
lock to improve scalability, but introduced a possible deadlock in
vhost-iotlb. vhost_iotlb_notify_vq() now takes vq->mutex while holding
the device's IOTLB spinlock. And on the vhost_iotlb_miss() path, the
spinlock is taken while holding vq->mutex.

Since calling vhost_poll_queue() doesn't require any lock, avoid the
deadlock by not taking vq->mutex.

Fixes: 78139c94 ("net: vhost: lock the vqs one by one")
Acked-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>