Enabling the default port on the VEB causes all outgoing traffic from
virtual functions to be copied to the physical function.  The default
port is only supposed to be used if you wish to bridge the physical
function to a SW switch such as Open vSwitch or the Linux bridge. That
allows the SW switch to route traffic to VMs that are not using a
virtual function.

Eventually we'll want to implement the ndo_fdb_add, ndo_fdb_del, and
ndo_fdb_dump functions.  The ndo_fdb_add function would set the
default port on the VEB in those cases where the MAC/VLAN address
filters have overflowed.  Normally we would not want to use it.

Change-Id: I3990f0384fff2840c4e43bc0955dd0b701380852
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes two different problems.
1) The port VLAN configuration was not persistent across VF driver
   loads and unloads.

2) The port VLAN configuration was only correct the first time it was
   set. Switching the port VLAN on and off would cause subsequent VLAN
   configurations to be corrupted in the VSI.  Ensure that the correct
   bits are being set for the VSI port VLAN configuration.

Change-Id: I7ebf5329f77eb8d73ccd3324eb346b3abeea737d
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver needs to clean PBA only when interrupts are turned off and we
are polling instead.

Change-Id: Ic0c1da761bd3abe7f73b1cc8bcddf8e3a232fd0f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove references to I40E_FLAG_MQ_ENABLED from the code
as it doesn't seem to be used anywhere.

Change-Id: I4c89fb65b2cdd26fbb0c58fccbbb4b03f0e5f1b3
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The allocation and clearing of rings for a VSI should be
using the alloc_queue_pairs and not num_queue_pairs.

The alloc_queue_pairs per VSI is a pre-allocated number
of queues assigned to a VSI; based on number of TCs enabled
only certain number of queues may be used from that. This
is mainly valid only for the LAN VSI case as that is the
only VSI that may be enabled with multiple traffic classes.
In the future the number of TCs may change based on DCBX
configuration.

The actual number of queues that are enabled/configured is
based on the number of TCs enabled for a given VSI and that
is stored in num_queue_pairs.

With this change num_[tr]x_queues is unused so remove them.

Change-Id: I9c2f84778bb25f7313c630e9b002a0caa883ce29
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't try to free a q_vector that hasn't been set up as it can
panic the kernel.

Change-Id: I0650cc6c441d0779788c522c790293c276d14fbc
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Swap a couple lines around in the error handling if the kzalloc() for
the pf->vsi array fails.  This was causing a kernel BUG because the
call to i40e_clear_interrupt_scheme() was assuming the pf->vsi[] array
existed.  In this fix it is possible that i40e_reset_interrupt_capability()
will get called twice, but this is a safe action.

Change-Id: I939163ccaa89baac7511556d36bc873864c35ae1
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When cleaning the ARQ, we must reinitialize the buffer size each time we
go through the loop, because i40e_clean_arq_element returns the message
length in the same field. Without this change, subsequent messages can
be truncated to the length of the previous message.

Change-Id: Ic9c32ff843faf0fc3196d21351a1c3a60c6158eb
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce i40e_irq_dynamic_disable_icr0 and use it and its previously-
extant counterpart when appropriate.

Change-Id: Ieb4037874fba2e96fc2354b34a97a3cb8f6490f3
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove custom i40e functions around ethernet addresses that are
duplicating already existing kernel functionality.

Also ends up fixing a bug with multicast addresses.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make a define used in the header file by both VF and PF drivers.

Change-Id: Ie9e35adcc021cd6a8f7513934984eb4ed55774f5
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't complain when we disable queues that are already disable, or
enable them when they're already enabled. This removes a bunch of bogus
log messages that we see at every VF reset.

Change-Id: Ia127be572abdccc48a53d8c43f8a07b8bb920de1
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the VF reset flow so that it works on real hardware. After
discussions with the HW team, the reset flow has been changed
somewhat.

- Change the i40e_reset_vf function to a void type, and fix
  up the callers to reflect this.
- Move the MSI-X disable code to i40e_free_vf_res since it must
  be done every time the VF is freed, regardless of whether or
  not it is reset.
- Ensure that the PCIe bus is quiet before polling the reset bit.
- Don't clear the VFGEN_RSTAT1 register at the beginning as it is
  cleared by the reset.
- Poll longer for the reset to be done.
- Disable the queues using an existing function rather than
  rolling our own.
- Free and reallocate the VSI after reset to avoid rx hang.

Change-Id: I11e2590431cb73e8663714d1cc5b23d59b809033
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This adds the implementation for the VXLAN ndo's.  This allows the
hardware to do RX checksum offload for inner packets on the UDP ports
that VXLAN notifies us about.
Signed-off-by: NJoseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add curly-braces on a multi-line function.  While we're here we
also change to return void in i40e_vsi_clear_rings() since no
caller cares.

Change-Id: I261fcef20e2a39e18d83ec08fdd14456131dee91
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wake on LAN is disabled by default and will remain that way for most
platforms, but there is an NVM setting that allows vendors to enable it
for a port if they think they've provided the right power environment
for the device.  This patch adds code to check the NVM setting and enable
Magic Packet use if WoL is enabled for the port.

Since only Magic Packet is supported, there's not a lot of HW configuration
needed.

Change-Id: I44e904a7b15695e34683009f487064cd86ea59b0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Call i40e_set_pci_config_data from probe, then check that
we are in a 8GT/s x8 PCIe slot and send a warning if we are not.

Change-Id: I62815c574cee50d2787c50bbe956dde7a7a75a11
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The HMC error interrupt would generate an un-necessary message
"unhandled interrupt", causing extra log spam, in addition to causing
a reset that was not necessary.  Prevent this issue by handling the
HMC error case explicitly, and only reset if the interrupt was from
some of the other causes.

Change-Id: Iabd203ba1dfc26a136b638597f3e9991acfa29f3
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Version updated to 0.3.14-k
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

No functional change, but the wrong defines were being used.

Change-Id: Ica2afd2dfe18154ca0f1260a508f31e372319ba7
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add basic support for handling suspend and resume.  We'll add
Wake-on-LAN support later.

Change-Id: Iea5e11c81bd9289a5bdbf086de8f626911a0b5ce
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Any user-initiated path which eventually calls reset needs
to hold the rtnl_lock, so add functionality to do that.

Be careful not to use the safe reset when cleaning up
from the diagnostic tests, which avoids rtnl_lock
recursion from ethtool.

Protect the reset_task with rtnl_lock, since it runs from a work item.

Change-Id: Ib6e7a3fb2966809db2daf35fd5a123ccdf6f6f0f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is the second of 3 patches that allows for changing
the number of queues in the driver on the fly.

This patch adds a function that calls the reinit flow for the
main VSI after making changes to the RSS queue count as requested
by the user.

Change-Id: I82dee91e9fe90eeb4e84a7369f4b8b342155dd85
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is the first in a 3 series patchset to implement
dynamically changing the queue count for the main VSI.

This patch starts by adding a reinit flow. This flow is designed
to be able to change just the queue count and not the number of
interrupt vectors that the device originally came up with.

Change-Id: I0634aaebf7dc4dd6c66af8f9dbbef89d7beac438
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current driver default sets the number of transmit/receive
queue pairs based on the current node's CPU count.

A better method is to use the total number of CPUs in the system
to suggest the number of queue pairs, which aligns better with
the behavior of ixgbe, and also with the expectations of the
kernel XPS and other subsystems in the stack.

Change-Id: If3e20c7f100f13e51d69762594d948f247ffe0c8
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Prevent some compiler warnings and implement some other
trivial fixes.

Change-Id: I7f49d79b91b94df1ad4a8306a0410ed72238845f
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Refactor flow control set up and disable L2 flow
control by default.

Change-Id: I2fe257b80df6d9a1e37deb4df118da8f8467040d
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Call the netif_set_real* functions in order to make sure
the stack knows about how many queues we have, in order
for RFS/RPS/XFS to work correctly.

Change-Id: Ib7a7b2792f80c5eef210dedf42cc6607d63953d2
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the vsi->tx_rings structure is NULL we don't want to panic.

Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Version updated to 0.3.13-k
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Track the number of physical functions (PFs) found, this is a global counter
on purpose so that each pf loaded has a unique ID.

Change-Id: I74d618520afbce4a774d0235449e3b5f97ff6d4a
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Print a message to notify the user of how many VFs are initialized on each
port.

Change-Id: I29ac2acc478ee4e588fd6ffcc35133d4c6607ca9
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VSI may be allocated more queues (alloc_queue_pairs) than actually
are to be used (num_queue_pairs), so only allocate rings for the queues
to be used.  The numbers will likely be the same for most VSIs, but can
be different based on how TCs are assigned and enabled.

Change-Id: Ie40f7ad0affbc4b45d6f049bcf02ee2fa24edc74
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RSS can steer packets based on recognition of all
sorts of different headers.  Enable some more of them.

Change-Id: I2264dedae66fb0bceca6fb6e772e050e3ca8efc8
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to re-size queues and vectors while the interface is
still up, we need to be able to call functions to free and
re-allocate without bringing down the VSI.

We also need to reset the existing setup, update the
configuration and then rebuild again. This requires us to have
the reset flow broken down into two parts.

Change-Id: I374dd25aabf769decda69b676491c7b7730a4635
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the driver version to 0.3.12-k
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable a couple of workarounds based on revision ID that allow the
driver to work more fully on early hardware.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a new flag to the add VEB command which allows the
driver to request the hardware to filter on L2 parameters.

This is an implementation of the driver access to a new firmware
feature.

Change-Id: Id61d3cad4125bdc68b8fd9d555c448a10c344b6b
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow debugfs to trigger a reset called EMPR.

Change-Id: I2f6600a8242759ec60c8198d03f70c2b774e0740
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a quick ethtool test for interrupts using the SW interrupt.
Also, change the loopback test (for now) to not report failure.

Change-Id: Id8ef154b82475e3163087a8d1df01dfec4d529fc
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>