Initialize the 'regmap_rtc' on S2MPA01 to some sane value. Sane at least
for S5M87X chipsets, not S2MPS/S2MPA but it won't be used because
rtc-s5m driver does not support S2MPA01.

This fixes following error:
drivers/mfd/sec-core.c:342:45: warning: ‘regmap_rtc’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The tps65910_i2c_probe() allocates regmap_irq_chip in
tps65910_irq_init() but it does not clean this up in case of
mfd_add_devices() failure.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Fixes: 4aab3fad ("mfd: tps65910: Move interrupt implementation code to mfd file")

tps65910_irq_init() sets 'tps65910->chip_irq' before calling
regmap_add_irq_chip(). If the regmap_add_irq_chip() call fails in
memory allocation of regmap_irq_chip_data members then:

1. The 'tps65910->chip_irq' will still hold some value
2. 'tps65910->irq_data' will be pointing to already freed memory
   (because regmap_add_irq_chip() will free it on error)

This results in invalid memory access during driver remove because the
tps65910_irq_exit() tests whether 'tps65910->chip_irq' is not zero.

Cc: <stable@vger.kernel.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Dummy I2C device allocated in sec_pmic_probe() leaked if
devm_regmap_init_i2c() failed. Unregister it before returning from
probe.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add of_compatible strings for S5M8767 and S2MPS14 clock MFD cells.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The tnetv107x platform is getting removed, so this driver
is not needed any more.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add bindings documentation for clocks on S5M8767 and S2MPS14 devices.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This fixes below build error.

FATAL: drivers/mfd/bcm590xx: sizeof(struct i2c_device_id)=24 is not a modulo of the size of section __mod_i2c_device_table=392.
Fix definition of struct i2c_device_id in mod_devicetable.h
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch adds the LPC Controller Device IDs for Watchdog and GPIO for
the Intel Bay Trail Atom SoC.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The NM10's GPIO is compatible with ICH v7 GPIO.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NDan Weinlader <danw@vs-networks.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The register layout of the Avoton is compatible with the iTCO v3
register layout.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NRajat Jain <rajatjain@juniper.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some new Atom's, eg Avoton and Bay Trail, have slightly different iTCO
functionality:
- The watchdog timer ticks at 1 second instead of .6 seconds

- Some 8 and 16-bit registers were combined into 32-bit registers

- Some registers were removed (DAT_IN, DAT_OUT, MESSAGE)

- The BOOT_STS field in TCO_STS was removed

- The NO_REBOOT bit is in the PMC area instead of GCS

Update the driver to support the above changes and bump the version to
1.11.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NRajat Jain <rajatjain@juniper.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some newer Atom CPUs, eg Avoton and Bay Trail, use slightly different
register layouts for the iTCO than the current v1 and v2 iTCO.
Differences from previous iTCO versions include:
- The ACPI space is enabled in the "ACPI base address" register instead
  of the "ACPI control register"

- The "no reboot" functionality is set in the "Power Management
  Configuration" register instead of the "General Control and Status"
  (GCS) register or PCI configuration space.

- The "ACPI Control Register" is not present on v3.  The "Power
  Management Configuration Base Address" register resides at the same
  address is Avoton/Bay Trail.

To differentiate these newer chipsets create a new v3 iTCO version and
update the MFD driver to support them.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NRajat Jain <rajatjain@juniper.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Future chipsets will use different register layouts that don't map
cleanly to the lpc_ich_cfg fields.  Remove the lpc_ich_cfg struct and
add explicit fields to the higher level lpc_ich_priv structure.

This change should have no functional impact.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NRajat Jain <rajatjain@juniper.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Some chipsets don't currently have GPIO support enabled.  For these
chipsets don't go through the process of initializing the GPIO region.

Make the same change for the watchdog initialization for chipsets which
may not enable the WDT in the future.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NRajat Jain <rajatjain@juniper.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The original bitmask of 0x10 was incorrect and would result in a write
to a reserved read-only bit instead of enabling the ACPI I/O
region.  Update it to the proper value of 0x80.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NRajat Jain <rajatjain@juniper.net>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add a driver for the BCM590xx PMU multi-function devices. The driver
initially supports regmap initialization and instantiation of the
voltage regulator device function of the PMU.
Signed-off-by: NMatt Porter <mporter@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add a DT binding for the BCM590xx PMUs. The binding inherits from
the generic regulator bindings.
Signed-off-by: NMatt Porter <mporter@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

MAXIM 14577 MFD driver uses the regmap_irq_chip so it's Kconfig entry
should select REGMAP_IRQ.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

There are some unused registers in twl4030 at I2C address 0x49 and function
twl4030_49_nop_reg() is used to check accessibility of that registers. These
registers are written in decimal format but the values are correct in
hexadecimal format. (It can be checked few lines above the patched code -
these registers are marked as unused there.)

As a consequence three registers of audio submodule are treated as
inaccessible (preamplifier carkit right and both handsfree registers).

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Novotny <tomas@novotny.cz>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Reported error was:
  ERROR: "regmap_del_irq_chip" [drivers/mfd/tps65218.ko] undefined!
    when CONFIG_REGMAP_IRQ is not enabled.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This patch updates the register definitions for DA9063 to support the
production silicon variant code ID (0x5). These changes are not backwards
compatible with the previous register definitions and can only be used
with the production variant of DA9063.
Signed-off-by: NOpensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Since we do not want to add new platform IDs for the syscon driver,
there is no reason to iterate over IDs. This patch simplifies
syscon_match_pdevname() function to remove such iteration.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

platform_get_irq() returns a negative error code when an IRQ is invalid
or unspecified.  Make 'irq' signed to properly handle this.
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NJosh Cartwright <joshc@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

vexpress_config_bridges is local to this file.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The FUSE7_REG register is not currently marked readable. This causes
as3722_sd0_is_low_voltage() to emit an error during boot, and assume
the range of the SD0 regulator:

as3722-regulator as3722-regulator: Reg 0xa7 read failed: -5

Fixes: d4807ad2 ("regmap: Check readable regs in _regmap_read")
  [exposed the bug, by checking for readability]
Fixes: 762a8ee8 ("regulator: as3722: detect SD0 low-voltage mode")
  [left out this register from the readable list]
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

We don't need to implement a dummy irq_set_wake op if we just set
IRQCHIP_SKIP_SET_WAKE.
Suggested-by: NJosh Cartwright <joshc@codeaurora.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This isn't necessary as we aren't setting the summary interrupt
to wake up the system in the irq_wake() callback.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The probe routine should call spi_setup() to configure the SPI bus
so it can properly communicate with the device.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The patch adds the maximum speed limit in accordance with the
PMIC datasheet if other value is not given in the devicetree
description or board data.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

PM8921 and PM8058 are PMICs found paired with MSM8960 and MSM8660
devices respectively. They contain subdevices such as keypads,
RTC, regulators, clocks, etc.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow this driver to be compiled on all ARM builds as it doesn't
rely on anything within arm/mach-msm.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Allow this driver to probe based on devicetree.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Use a regmap so that the pm8xxx read/write APIs can be removed
once all consumer drivers are converted.
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add read and write helper functions that the pm8921-core driver
can use to read and write ssbi registers via a "no-bus" regmap.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Convert this driver to use irqdomains so that the PMIC's child
devices can be converted to devicetree.
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>