A utility routine to print common entries used
for ACPI-related DMI blacklist entries.
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI and APM used "pm_active" to guarantee that
they would not be simultaneously active.

But pm_active was recently moved under CONFIG_PM_LEGACY,
so that without CONFIG_PM_LEGACY, pm_active became a NOP --
allowing ACPI and APM to both be simultaneously enabled.
This caused unpredictable results, including boot hangs.

Further, the code under CONFIG_PM_LEGACY is scheduled
for removal.

So replace pm_active with pm_flags.
pm_flags depends only on CONFIG_PM,
which is present for both CONFIG_APM and CONFIG_ACPI.

http://bugzilla.kernel.org/show_bug.cgi?id=9194Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

http://bugzilla.kernel.org/show_bug.cgi?id=8171Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

When PCI IDE controller works in legacy mode and no PRT entry is found
in ACPI PRT table, OSPM will neither read the irq number from the IDE
PCI configuration space nor call the function of acpi_register_gsi to
register gsi.

http://bugzilla.kernel.org/show_bug.cgi?id=5637Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This was writeable in 2.6.23 but the cpuidle merge made it read-only.  But
some people's scripts (ie: Mark's) were writing to it.

As an unhappy compromise, make max_cstate writeable again if the kernel was
configured without CONFIG_CPU_IDLE.

http://bugzilla.kernel.org/show_bug.cgi?id=9683Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9494Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some _STA methods called during bus_scan() might require EC region handler,
which might be enabled later in the scan.
Enable it explicitly before scan to avoid errors.

Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9627Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

klaptopd assumes rate to be in same units as capacity.

http://bugzilla.kernel.org/show_bug.cgi?id=9362Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

http://bugzilla.kernel.org/show_bug.cgi?id=9362Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Alarm bit should be cleared in order for other alarms to be sent.
http://bugzilla.kernel.org/show_bug.cgi?id=9362Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

for sn2_defconfig:

WARNING: vmlinux.o(.text+0x4b8601): Section mismatch: reference to .init.data:node_to_pxm_map (between '__acpi_map_pxm_to_node' and 'acpi_get_pxm')
WARNING: vmlinux.o(.text+0x4b8741): Section mismatch: reference to .init.data:pxm_to_node_map (between 'acpi_map_pxm_to_node' and 'acpi_get_node')
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The ->cap fields of struct acpi_video_device and struct acpi_video_bus
are 1B each, not 4B. The oversized memset()'s corrupted the subsequent
list_head fields. This resulted in silent corruption without
CONFIG_DEBUG_LIST and BUG's with it. This patch uses sizeof() to pass
the proper bounds to the memset() calls and thereby correct the bugs.
Signed-off-by: NWilliam Irwin <wli@holomorphy.com>
Acked-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NLen Brown <len.brown@intel.com>

The timer broadcast code might access HPET, which should not be
accessed after the busmaster disable.

In acpi_idle_enter_simple() this change also prevents, that we modify
the busmaster state without going actually idle. This might leave the
ACPI bm state in a stale state, when we leave the function early in
the need_resched() check.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>

At least some systems report technology information with trailing spaces:

{pts/1}% cat -E /var/tmp/bat/2.6.23 | grep type
battery type:            Li-ION  $

Use strncasecmp to compare model string to skip trailing part
Signed-off-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Acked-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Changed resolution of named references in packages

Fixed a problem with the Package operator where all named
references were created as object references and left otherwise
unresolved. According to the ACPI specification, a Package can
only contain Data Objects or references to control methods. The
implication is that named references to Data Objects (Integer,
Buffer, String, Package, BufferField, Field) should be resolved
immediately upon package creation. This is the approach taken
with this change. References to all other named objects (Methods,
Devices, Scopes, etc.) are all now properly created as reference objects.

http://bugzilla.kernel.org/show_bug.cgi?id=5328
http://bugzilla.kernel.org/show_bug.cgi?id=9429Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The IRQ operation(enable/disable) should be avoided when throttling is
controlled via PTC method. It is replaced by the migration of task.

This fixes an oops on T61 -- a regression due to
f79f06ab b/c FixedHW support tried to read remote MSR with interrupts disabled.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.

The pointers to per cpu data are typically not initialized for processors
that are not present.  So we seem to be reading something here from offset
0 in memory.

Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.

Convert one loop to NR_CPUS to use the cpu_possible map instead.  That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

AMD Opteron processors before CG revision don't like C-states > 1.

This solves the long standing bugzilla #5303 and probably some more
on affected machines:

  http://bugzilla.kernel.org/show_bug.cgi?id=5303

[ tglx@linutronix.de: reworked the patch so it does not wreck ia64 ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Some controllers fail to send confirmation GPE after address or data write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e7), which did only read address.

Reference: http://bugzilla.kernel.org/show_bug.cgi?id=9327Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: NRomano Giannetti <romano.giannetti@gmail.com>
Tested-by: Mats Johannesson
Signed-off-by: NLen Brown <len.brown@intel.com>

Sometimes it is usefull to see raw protocol dump.
Uncomment '#define DEBUG' at the beginning of file to make EC
really verbose.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit f2d68935.

In cases where acpi_pci_bind() does not
attach device data, acpi_pci_unbind()
complains via an ACPI exception about the missing data when
the device is removed.  For example, acpi_pci_bind() does not
attach data for non-existent device functions so when the device
is removed using the ACPI PCI hotplug driver 'acpiphp' an ACPI
exception is logged for every non-existent function.  This patch
avoids the confusing log messages by removing the unnecessary
ACPI exception.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355

cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Port 2aa44d05
(sched: sched_clock_idle_[sleep|wakeup]_event()) to cpuidle.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Port 18eab855
(Enable C3 even when PM2_control is zero) to cpuidle.

Without this patch, some systems will notice a regression
when enabling CPU_IDLE -- C3 would no longer be available.
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Option to init EC early inserted to handle #8598 ASUS problem,
introduced several others.

EC driver in this particular case has fake _INI method, not present on
other machines, which don't need or break from this workaround, so lets use
its presence as a flag for early init.

http://bugzilla.kernel.org/show_bug.cgi?id=9262
http://bugzilla.kernel.org/show_bug.cgi?id=8598
https://bugzilla.novell.com/show_bug.cgi?id=334806Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit cbff2fbf.

This reverts commit 6e800af2.

Introduce new ACPI_PROCFS_POWER (default Yes) config option and move
procfs code in battery, ac, and sbs drivers under it.
This is done to allow ACPI_PROCFS to be default No.
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

In order to be able to write the value "100"
to /proc/acpi/video/.../brightness, we have to allocate 5 bytes:
4 characters will be written (1, 0, 0 plus null byte),
and 1 byte should be buffer for a terminating NULL character.

http://bugzilla.kernel.org/show_bug.cgi?id=9278Signed-off-by: NDanny Baumann <dannybaumann@web.de>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some controllers fail to send confirmation GPE after address write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e7), which did only read address.

http://bugzilla.kernel.org/show_bug.cgi?id=9327Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: NRomano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

drivers/acpi/sbs.c: In function acpi_battery_add:
drivers/acpi/sbs.c:811: warning: ignoring return value of device_create_file,
declared with attribute warn_unused_result

Additional cleanups:
* use struct acpi_battery in acpi_battery_remove() to clean up function
calls, just like acpi_battery_add() already does.

* put braces around unregister call, as it depends on dev being not NULL.

* remove unneeded braces
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NAlexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

_TSS was erroneously ignored, in favor of the FADT.

When TSS is used, the access width is included in the PTC control/status
register.  So it is unnecessary that the access bit width is multiplied by 8.
At the same time the bit_offset should be considered for system I/O Access.

It should be checked the bit_width and bit_offset of PTC regsiter in order to
avoid the failure of system I/O access. It means that bit_width plus
bit_offset can't be greater than 32.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Change the function interface for throttling control via PTC.
The following functions are concerned:

acpi_read_throttling_status()
acpi_write_throttling_state()
acpi_get_throttling_value()
acpi_get_throttling_state()
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Factor out legacy FADT.duty_width code
and run it only in the non _TSS case.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

We've run into BIOS that hand us 4-bit access width requests
for T-state control when the code expected only multipls of 8-bits.
Round up.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

When a T-state limit change notification is received,
Linux must evaluate _TPC and change its current
T-state immediately to comply with the new limit.

Previously, Linux would notice the new limit
only upon the next throttling change.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>