- 09 8月, 2010 19 次提交
-
-
由 Andy Walls 提交于
There is a distinction on IR Tx for the CX2388[578] chips of carrier sense inversion (space is a carrier burst and mark is no burst) and I/O pin level inversion (0 is high output level, 1 is low output level). Allow the caller to set these parameters distinctly as v4l2_subdevice IR parameters. This permits the IR device to be configured and enabled without the IR Tx LED being on during idle/space time due to an external hardware level inversion Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Add s_io_pin_config core subdev op for the CX2388[578] AV cores. This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N. It likely needs work for the I2S signal direction. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
Add a simple log_status function for raw analog video capture device nodes, to provide insight into the state of the CX2388[578] A/V decoder core. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0 vs. the standard 0x80. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Andy Walls 提交于
There was a small window between writing the cx25840 register address over the i2c bus and reading the register contents back from the cx25840 device that the i2c adapter lock was released. This change ensures the adapter lock is not released until the register read is done. Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean Delvare 提交于
Function i2c_wait_done() never returns negative values, so there is no point in checking for them. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean Delvare 提交于
Don't just check for nacks on zero-length transactions. Check on other transactions too. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean Delvare 提交于
Documentation/i2c/fault-codes says that i2c adapter drivers should return -ENXIO when no slave acks an address byte. Signed-off-by: NJean Delvare <khali@linux-fr.org> Signed-off-by: NAndy Walls <awalls@md.metrocast.net> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
On laptops, the webcam sometimes disconnects when writing the first main register (b300). This patch prevents the creation of a new /dev/video<n> on streaming start. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The added controls are exposure, gain, autogain and backlight compensation. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The JPEG format did not work fine. The Bayer format offers correct VGA (640x480) resolution, but bad QQVGA (160x120). This last resolution is removed. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The bit 7 of the sensor gain register multiplies the 7bits value by two. It is now always set with half the user gain value. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The start_1 exchange must be done by (reg, val) * 5 and not 8. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Jean-François Moine 提交于
The sensor enum definition was not at the right place. Signed-off-by: NJean-François Moine <moinejf@free.fr> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 07 8月, 2010 3 次提交
-
-
由 Linus Torvalds 提交于
Commit 69309a05 ("x86, asm: Clean up and simplify set_64bit()") sanitized the x86-64 types to set_64bit(), and incidentally resulted in warnings like drivers/pci/intr_remapping.c: In function 'modify_irte': drivers/pci/intr_remapping.c:314: warning: passing argument 1 of 'set_64bit' from incompatible pointer type arch/x86/include/asm/cmpxchg_64.h:6: note:expected 'volatile u64 *' but argument is of type 'long unsigned int *' It turns out that the change to set_64bit() really does clean up things, and the PCI intr_remapping.c file did a rather ugly cast in order to avoid warnings with the previous set_64bit() type model. Removing the ugly cast fixes the warning, and makes everybody happy and expects a set_64bit() to take the logical "u64 *" argument. Pointed-out-by: NPeter Anvin <hpa@zytor.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Stern 提交于
Fake "address-of" expressions that evaluate to NULL generally confuse readers and can provoke compiler warnings. This patch (as1411) removes one such fake expression, using an "#ifdef" in its place. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Howells 提交于
Make /dev/console get initialised before any initialisation routine that invokes modprobe because if modprobe fails, it's going to want to open /dev/console, presumably to write an error message to. The problem with that is that if the /dev/console driver is not yet initialised, the chardev handler will call request_module() to invoke modprobe, which will fail, because we never compile /dev/console as a module. This will lead to a modprobe loop, showing the following in the kernel log: request_module: runaway loop modprobe char-major-5-1 request_module: runaway loop modprobe char-major-5-1 request_module: runaway loop modprobe char-major-5-1 request_module: runaway loop modprobe char-major-5-1 request_module: runaway loop modprobe char-major-5-1 This can happen, for example, when the built in md5 module can't find the built in cryptomgr module (because the latter fails to initialise). The md5 module comes before the call to tty_init(), presumably because 'crypto' comes before 'drivers' alphabetically. Fix this by calling tty_init() from chrdev_init(). Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 06 8月, 2010 18 次提交
-
-
由 Andrew Morton 提交于
drivers/video/via/via-gpio.c: In function 'viafb_gpio_probe': drivers/video/via/via-gpio.c:216: warning: assignment from incompatible pointer type Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
-
由 Ben Hutchings 提交于
VIA UniChrome and Chrome9 GPUs only exist as Integrated Graphics Processors in x86 chipsets. Signed-off-by: NBen Hutchings <ben@decadent.org.uk> Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
-
由 Henrik Kretzschmar 提交于
This patch moves two functions from .devexit to .text, which are called on the probe error path. Also a function which is called by probe is moved from .text to .devinit. WARNING: vmlinux.o(.devinit.text+0x2ca5): Section mismatch in reference from the function via_pci_probe() to the function devexit.text:via_teardown_subdevs() The function __devinit via_pci_probe() references a function __devexit via_teardown_subdevs(). This is often seen when error handling in the init function uses functionality in the exit path. The fix is often to remove the __devexit annotation of via_teardown_subdevs() so it may be used outside an exit section. WARNING: vmlinux.o(.devinit.text+0x2cb1): Section mismatch in reference from the function via_pci_probe() to the function devexit.text:via_pci_teardown_mmio() The function __devinit via_pci_probe() references a function __devexit via_pci_teardown_mmio(). This is often seen when error handling in the init function uses functionality in the exit path. The fix is often to remove the __devexit annotation of via_pci_teardown_mmio() so it may be used outside an exit section. Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
-
由 David Miller 提交于
Fix build failure on sparc64 which is missing the include of <linux/slab.h> via <asm/pci.h> that x86, powerpc, ia64, etc. have. Signed-off-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Julia Lawall 提交于
list_for_each_entry binds its first argument to a non-null value, and thus any null test on the value of that argument is superfluous. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ iterator I; expression x; statement S,S1,S2; @@ I(x,...) { <... - if (x == NULL && ...) S ...> } // </smpl> Signed-off-by: NJulia Lawall <julia@diku.dk> Acked-by: NAlexander Schmidt <alexs@linux.vnet.ibm.com> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Roland Dreier 提交于
Fix confusing indentation that makes a statement look as if it's part of an if statement when in fact it isn't. Reported-by: NJulia Lawall <julia@diku.dk> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
由 Christoph Fritz 提交于
Commit fa61cf70 updates nl80211's function .set_tx_power to use mBm units instead of dBm for greater accuracy and smaller power levels. This patchs updates prism2_set_tx_power() accordingly. Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johannes Berg 提交于
The new_name argument to device_rename() can be const as kobject_rename's new_name argument is. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Guenter Roeck 提交于
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com> Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Guenter Roeck 提交于
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Guenter Roeck 提交于
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Guenter Roeck 提交于
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Magnus Damm 提交于
Add BUS_NOTIFY_BIND_DRIVER as a bus notifier event. For driver binding/unbinding we with this in place have the following bus notifier events: - BUS_NOTIFY_BIND_DRIVER - before ->probe() - BUS_NOTIFY_BOUND_DRIVER - after ->probe() - BUS_NOTIFY_UNBIND_DRIVER - before ->remove() - BUS_NOTIFY_UNBOUND_DRIVER - after ->remove() The event BUS_NOTIFY_BIND_DRIVER allows bus code to be notified that ->probe() is about to be called. Useful for bus code that needs to setup hardware before the driver gets to run. With this in place platform drivers can be loaded and unloaded as modules and the new BIND event allows bus code to control for instance device clocks that must be enabled before the driver can be executed. Without this patch there is no way for the bus code to get notified that a modular driver is about to be probed. Signed-off-by: NMagnus Damm <damm@opensource.se> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jike Song 提交于
Reported-by: huangweibing@gmail.com Signed-off-by: NJike Song <albcamus@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Axel Lin 提交于
smi_data_buf_free is called twice in current implementation. The second call simply return because smi_data_buf is set to NULL in first call. This patch removes the second smi_data_buf_free call. Signed-off-by: NAxel Lin <axel.lin@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Axel Lin 提交于
This patch adds a missing kfree(dmi_dev) in dmi_id_init error path. Signed-off-by: NAxel Lin <axel.lin@gmail.com> Acked-by: NTejun Heo <tj@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Uwe Kleine-König 提交于
Platform devices should only be called by init code, so it should be possible to move creation helpers to .init.text -- at least if modules are disabled. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Uwe Kleine-König 提交于
This makes the two similar functions platform_device_register_simple and platform_device_register_data one line inline functions using a new generic function platform_device_register_resndata. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-