Phy is compatible with Vitesse 8221.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Remove trailing white space
- Remove spaces before tag
- Fix comments
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds device tree parsing support for the shared driver of mv643xx_eth.
As the bindings are slightly different from current PPC bindings new binding
documentation is also added. Following PPC-style device setup, the shared
driver now also adds port platform_devices and sets up port platform_data.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet controllers found on Kirkwood SoCs not only suffer from loosing
MAC address register contents on clock gating but also some important
registers are reset to values that would break ethernet. This patch
clears the CLK125_BYPASS_EN bit for DT enabled Kirkwood only by using
of_device_is_compatible() instead of #ifdefs. Non-DT Kirkwood is not
affected as it installs a clock gating workaround because of the MAC
address issue above. Other Orion SoCs do not suffer from register reset,
do not have the bit in question, or do not have the register at all.
Moreover, system controllers on PPC using this driver should also be
protected from clearing that bit.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This connects to a phy node passed to the port device instead of probing
the phy by phy_addr.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of managed devm_ioremap and remove corresponding iounmap.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a separated mdio bus driver with mvmdio, phy_detach on network device
removal will not stop the phy and finally lead to NULL pointer dereference
in mvmdio due to non-existent network device. Use phy_disconnect instead
to properly stop phy device from accessing network device prior removal of
the network device.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct email address and years.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable emaclite for Xilinx ARM Zynq platform.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Emaclite can be used on ARM zynq where in_be32/out_be32 IO
functions are not present. Use standard __raw_readl/__raw_writel
IO functions instead.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xemaclite_adjust_link is used locally.
It removes sparse warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:916:6: warning:
symbol 'xemaclite_adjust_link' was not declared. Should it be static?
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For system which contains at least two ethernet IP where
one IP manage MDIO bus with several PHYs.

Example dts node:
ethernet_mac0: ethernet@81000000 {
	compatible = "xlnx,xps-ethernetlite-1.00.a";
	device_type = "network";
	interrupt-parent = <&xps_intc_0>;
	interrupts = < 1 0 >;
		local-mac-address = [ 00 0a 35 00 db bb ];
	phy-handle = <&ethernet_mac0_phy0>;
	reg = < 0x81000000 0x10000 >;
	xlnx,duplex = <0x1>;
	xlnx,family = "spartan3e";
	xlnx,include-internal-loopback = <0x0>;
	xlnx,include-mdio = <0x1>;
	xlnx,rx-ping-pong = <0x0>;
	xlnx,tx-ping-pong = <0x0>;
	ethernet_mac0_mdio {
		#address-cells = <1>;
		#size-cells = <0>;
		ethernet_mac0_phy0: phy@1 {
			reg = <0x1>;
		} ;
		ethernet_mac0_phy1: phy@3 {
			reg = <0x3>;
		} ;
	} ;
} ;
ethernet_mac2: ethernet@81040000 {
	compatible = "xlnx,xps-ethernetlite-1.00.a";
	device_type = "network";
	interrupt-parent = <&xps_intc_0>;
	interrupts = < 11 0 >;
		local-mac-address = [ 00 0a 35 00 db bb ];
	phy-handle = <&ethernet_mac0_phy1>;
	reg = < 0x81040000 0x10000 >;
	xlnx,duplex = <0x1>;
	xlnx,family = "spartan3e";
	xlnx,include-internal-loopback = <0x0>;
	xlnx,include-mdio = <0x0>;
	xlnx,rx-ping-pong = <0x0>;
	xlnx,tx-ping-pong = <0x0>;
} ;
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be more verbose when any problem happens.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Adapters do not support co-existence of INTx Interrupt with
  MSI-X or MSI among multiple functions. Prevent attaching
  of a function during normal load, if adapter gets into mixed
  mode of interrupts
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o log "Unknown" board name and "Unknown" serial number in case
  of mismatched adapter type found. This will avoid weird characters
  logs when an adapter is in bad state or corrupted.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of dereferencing pointer and put values on stack we could use nice
%*phC specifier.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After b924551b ("bonding: fix enslaving in alb mode when link down") we
don't need the bond parameter in alb_swap_mac_addr(), so remove it.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When vxlan is compiled as builtin, its init code
runs before IPv6 init, this could cause problems
if we create IPv6 socket in the latter patch.

Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'unsigned int' is slightly better.

Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>

v2->v3: fix typo on simeth
	shortened dev_getter
	shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the xmit_hash_policy pointer is always valid and not dependent on
anything, we can change it while the bond device is up and running. The
only downside would be the out of order packets but that is a small price
to pay.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

module_spi_driver() removes some boilerplate and makes the code
simpler.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these
as internal PHY devices.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to save power, let's disable the regulator in the suspend function and
enable it in resume.

Tested on a mx28evk board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During probe the clocks are enabled prior than the acquiring the interrupts.

In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case of error during probe, disable the PHY regulator.

Do the same in fec_drv_remove().
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.

This is wrong because at this point the interrupts have not even been acquired.

Swap failed_init/failed_irq to fix the error path.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().

This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>