In the error case we call skge_rx_reuse twice. This is harmless
but unnecessary.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The skge driver was using dev_alloc_skb which reserves space for the
Ethernet header. This unnecessary and it should just use alloc_skb,
also by using GFP_KERNEL during startup it won't run into problems when
a user asks for a huge ring size or mtu and potentially drains the
reserved atomic pool.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The skge driver aligns the header on the initial receive buffers, but
but doesn't on followon receive buffer allocations.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update version number
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When a PCI error occurs, try and report more info.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reformat some code to make it easier to read. And whitespace
fixes.
Signed-off-by: NStephen Hemminger <sheminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add mmio barriers at the appropriate places, don't have a platform
that needs them, but this is where the documentation of the patch
says to add them.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use kcalloc when allocating ring data structure.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Cleanup of the part of the code that sets up DMA configuration.
Should cause no real change in operation, just clearer.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The SysKonnect Genesis and Yukon chip sets have restrictions on the possible
control block area.  The memory needs to not cross 4 Gig boundary, and it needs
to be 8 byte aligned.  This patch checks and fails to bring the device up
if region is unacceptable.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve performance of skge driver by not touching irq mask
register as much. Since the interrupt source auto-masks, the driver
can just leave it disabled until the end of the soft irq.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Cleanup transmit buffers using NAPI.  This allows the transmit routine
to leave interrupts enabled, and that improves performance.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There is a race between updating the irq mask and setting it
which can be triggered on SMP with a bad cable.
Similar patch from Ingo Molnar and Thomas Gleixner
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The SysKonnect Genesis based board would fail on initialization
with phy_read errors caused by not waiting for last phy write.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Fix a race in the receive NAPI, irq handling. The interrupt clear and the
start need to be separated.  Otherwise there is a window between the last
frame received and the NAPI done level handling.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

This is a clone of John Linville's fixed for speed setting on sky2 driver.
The skge driver has the same code (and bug). It would not allow manually forcing
100 and 10 mbit.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.

Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also have to handle out of memory condition on resume.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Enough changes for one version.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

If changing ring parameters is unable to allocate memory, we need
to return an error and take the device down.

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5715Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Changing the MTU size causes the receiver to have to reallocate buffers.
If this allocation fails, then we need to return an error, and take
the device offline. It can then be brought back up or reconfigured
for a smaller MTU.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Change the pause settings doesn't need to cause link to go down/up.
It can be handled by the phy_reset code.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Change the speed settings doesn't need to cause link to go down/up.
It can be handled by doing the same logic as nway_reset.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Get rid of warning in case of race with ring full and lockless
tx on the skge driver. It is possible to be in the transmit
routine with no available slots and already stopped.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

If using UDP over VLAN, with the skge driver there is a possibility
of generating an incorrect checksum. This is a unlikely occurrence
because it is only an issue on Yukon revision 0, and that revision
doesn't seem to exist on any current hardware (probably early prototype).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Increase the driver version number and print version when
probing.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix some of my bad spelling.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Use prefetch() in the interrupt path to try and look ahead
at the next place will be looking at in the ring.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Go into power down mode on shutdown.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Basic MII ioctl support for skge driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Can use kzalloc in skge driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When skge is booted up, the PHY may be stuck in power down state
by the previous OS. So we may need to turn it on.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Skge driver was bringing link up/down when changing mac
address.  This doesn't work in the bonding environment, and is
more effort than needed.

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5271Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This is one of those workarounds sucked over from sk98lin driver.
The skge driver needs to detect the Yukon-Lite A0 chip properly,
and turn of Rx FIFO Flush.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Cleanup receive buffer allocation and management,
Add more error handling checks from PHY and bump version.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Expand the returned data for ethtool debug access to include
all of the mapped PCI area; except for the small set of registers
that are for diagnostic RAM access. Access to those registers
will hang the system.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Merge of four previous patches and the Kconfig fix
 * Remove debug printk's
 * whitespace cleanup and version number change
 * clear interrupts, reset phy, and reset hardware on shutdown
 * ignore 64bit counter overflow interrupts
 * fix a couple of places where second port could clobber state
   of first port.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>