To prevent VBUS contention, the am335x MUSB phy senses VBUS first before
transitioning to host mode. However, for host-only mode, VBUS could be
directly tied to 5V power rail which could prevent MUSB transitions to
host mode.

This change receives dr_mode of the controller then bypass the first
VBUS sensing for host-only mode, so that MUSB can work in host mode
event if VBUS is tied to 5V.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The filename of am35x-phy-control.h is confusing. The header is used
by the am335x phy driver, but the filename refers to am35x. Even worse
there is indeed another device called am35x but it does not use this
header at all.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As of commit 3d7608e4 ("ARM: shmobile: bockw: remove legacy
board file and config"), the Renesas R-Car (Gen1) USB PHY driver is no
longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that would
require adding DT support to the driver. Instead, a new driver using the
generic PHY framework should be written, as was done for R-Car Gen2.

Remove the driver for good.
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, and the change is needed
to prevent a compilation failure, when mach/irq.h is removed.

Additionally remove other unneeded includes and sort out their order.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:

z -> for zero
s -> short not okay
i -> interrupt

A capital letter means the feature is enabled
while a lower case letter means it is disabled;

Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.

Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: NRavi B <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In general it is wise to clear interrupts before processing them.  If
you don't do that, you can get:
 1. Interrupt happens
 2. You look at system state and process interrupt
 3. A new interrupt happens
 4. You clear interrupt without processing it.

This patch was actually a first attempt to fix missing device insertions
as described in (usb: dwc2: host: Fix missing device insertions) and it
did solve some of the signal bouncing problems but not all of
them (which is why I submitted the other patch).  Specifically, this
patch itself would sometimes change:
 1. hardware sees connect
 2. hardware sees disconnect
 3. hardware sees connect
 4. dwc2_port_intr() - clears connect interrupt
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

...to:
 1. hardware sees connect
 2. hardware sees disconnect
 3. dwc2_port_intr() - clears connect interrupt
 4. hardware sees connect
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

...but with different timing then sometimes we'd still miss cable
insertions.

In any case, though this patch doesn't fix any (known) problems, it
still seems wise as a general policy to clear interrupt before handling
them.

Note that for dwc2_handle_usb_port_intr(), instead of moving the clear
of PRTINT to the beginning of the function we remove it completely.  The
only way to clear PRTINT is to clear the sources that set it in the
first place.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function.  As such no locks are already held when the
function is called.

Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks.  Let's add
locks.

The bug was found by code inspection only.  It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter.  Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some USB phy drivers have different handling for the controller in each
dr_mode. But the phy driver does not have visibility to the dr_mode of
the controller.

This adds an api to return the dr_mode of the controller which
associates the given phy node.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since now, we may have more than one request during the test, and
it is better we just quit once the error occurs instead of try
queueing further requests.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Suggested-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since composite now overwrites bcdUSB for any gadget, remove
setting it in legacy gadgets. All legacy gadgets set 0x0200, the
same as the value additionally set by composite, so there is no
behaviour change.
Signed-off-by: NIgor Kotrasinski <i.kotrasinsk@samsung.com>

Rebase onto current balbi/next
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In some cases, like when you've got a "Microsoft Wireless Keyboard 2000"
connected to dwc2 with a hub, expected that we'll get some transfer
errors sometimes.  The controller is expected to try at least 3 times
before giving up.  See figure "Figure A-67. Normal HS CSPLIT 3 Strikes
Smash" in the USB spec.

The dwc2 controller has a way to support this by using the "EC_MC"
field.  The Raspberry Pi driver has logic for setting this right.  See
fiq_fsm_queue_split_transaction() in their "dwc_otg_hcd.c".  Let's use
the same logic.

After making this change, we no longer get dropped characters from the
above mentioned keyboard.  Other devices on the same bus as the keyboard
also behave more properly.

Thanks for Julius Werner for the expert analysis and suggestions.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.

Specifically, the observed order is:
 1. hardware sees connect
 2. hardware sees disconnect
 3. hardware sees connect
 4. dwc2_port_intr() - clears connect interrupt
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.

We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted.  We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.

Notes:
1. As part of this change we add a "force" parameter to
   dwc2_hcd_disconnect() so that when we're unloading the module we
   avoid the new behavior.  The need for this was pointed out by John
   Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
   exactly the same bit of code from dwc2_port_intr().  To avoid
   duplication, we refactor that code out into a new function
   dwc2_hcd_connect().
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Support hisilicon,hi6220-usb for HiKey board
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Masks for HCDMA.CTD and HCDMA.DMAAddr are incorrect. As we always
start from first descriptor, no need to mask the address anyway.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use Streaming DMA mappings to handle cache coherency of frame list and
descriptor list. Cache are always flushed before controller access it
or before cpu access it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.

Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

timeval is deprecated and not y2038 safe.  Its size also changes according
to 32 bit/ 64 bit compilation.  Replace it with 32 and 64 bit versions of
its individual fields, giving two ioctls with different code values.
The two ioctls are necessary to maintain the 32 bit and 64 bit userspace
compatibility with a 64/32 bit kernel.

Change unsigned to __u32 types for a definitive userspace interface.
This is in accordance with the psABI that the unsigned type is always
32 bits.

Also use motonic timer instead of real time to ensure positive delta
values.

Refactor usbtest_ioctl for readability to isolate the handling of the
testing timing measurement.

The official testusb userspace tool can be changed in a separate patch
to reflect the __u32 changes as well. It can use the usbtest_param_32
struct, since 32 bit seconds is long enough for test durations.
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDeepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove unnecessary headers and variables.
Reviewed-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe F. Tonello <eu@felipetonello.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This function is shared between gadget functions, so this avoid unnecessary
duplicated code and potentially avoid memory leaks.
Reviewed-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe F. Tonello <eu@felipetonello.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This code is duplicated from f_midi_start_ep(midi, f, midi->out_ep).
Reviewed-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe F. Tonello <eu@felipetonello.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add both bulk and iso depth of queue entries.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch modifies the ep.caps.type_{iso,bulk,int} setting and
the second argument of usb_ep_maxpacket_limit() using
the dparam.pipe_configs.

In the previous code, all the type_{iso,bulk,int} were set to true.
However, to avoid waste time for finding suitable pipe in usb_ep_enable(),
this driver should set correct type.
Also the second argument of usb_ep_maxpacket_limit() was set to 512
even if the pipe is isochronous or interrupt. So, this driver could
not bind a gadget driver like the g_audio driver.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The current code has info->bufnmb_last to calculate the BUFNMB bits of
PIPEBUF register. However, since the bufnmb_last is initialized in
the usbhs_pipe_init() only, this driver is possible to set unexpected
value to the register if usb_ep_{enable,disable}() are called many times.

So, this patch modifies the pipe configuration via struct
renesas_usbhs_driver_param to simplify the code. Also this patch changes:
 - a double buffer configuration
 - isochronous buffer size from 512 to 1024
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Process all completed urbs, if more urbs are complete by the time
driver processes completion interrupt.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When releasing a channel, increment hsotg->available_host_channels even
in case a periodic channel is released.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Isochronous descriptor is currently programmed for the frame
after the last descriptor was programmed.

If the last descriptor frame underrun, then current descriptor must
take this into account and must be programmed on the current frame + 1.
This overrun usually happens when system is loaded and dwc2 can't init
descriptor list in time.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This function allow comparing frame index used for
descriptor list which has 64 entries.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Prevent dwc2 driver from accessing channel while it frees it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When completing non isoc xfer, dwc2_complete_non_isoc_xfer_ddma()
is relying on qtd->n_desc to process the corresponding number of
descriptors.

During the processing of these descriptors, qtd could be unlinked
and freed if xfer is done and urb is no more in progress.

In this case, dwc2_complete_non_isoc_xfer_ddma() will read again
qtd->n_desc whereas qtd has been freed. This will lead to unpredictable
results since qtd->n_desc is no more valid value.

To avoid this error, return a result != 0 in dwc2_process_non_isoc_desc(),
so that dwc2_complete_non_isoc_xfer_ddma() stops desc processing.

This has been seen with Slub debug enabled.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When a channel is halted because of urb dequeue during transfer
completion, no other qtds must be scheduled until halt is done.
Moreover, all in progress qtds must be given back.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Active bit must be enabled in all scheduled descriptors. Else transfer
never start.
Remove previous code which was not correctly configuring descriptors.
Active bit was set before calling dwc2_fill_host_isoc_dma_desc() which
is erasing dma_desc->status.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Increment qtd->isoc_frame_index_last before testing it, else below
check will never be true and IOC (Interrupt On Complete) bit for
last frame will never be set in descriptor status.

  /* Set IOC for each descriptor corresponding to last frame of URB */
  if (qtd->isoc_frame_index_last == qtd->urb->packet_count)
	dma_desc->status |= HOST_DMA_IOC;
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now the function of complicated_callback is not only used for iso
transfer, improve the error message to reflect it.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add both bulk and iso depth of queue for sourcesink.
Reviewed-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add queue depth for both iso and bulk transfer, with more queues, we
can do performance and stress test using sourcesink, and update g_zero
accordingly.
Reviewed-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now that we have a generic dwc3-of-simple.c, we can
use that instead of maintaining dwc3-qcom.c which is
extremely similar.

Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds binding doc for Xilinx DWC3 glue driver.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSubbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>