The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.

http://www.analogue-micro.com/ASP8347.htmlSigned-off-by: NBryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now that we properly set the physical address in the program header of the
vmlinux ELF we can extract it to properly set the load and entry point for
u-boot uImages.  Before we always hard coded the load & entry point to 0.
However there are situations that the kernel may be built with a non-zero
physical address.

We use objdump to extract the PHDR.  We assume that there is only one
PHDR in the vmlinux of type LOAD.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Improve the debugging support of the PS3 bootwraper code:

 o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
   allow for more debugging code in the overlay.
 o Use the dot symbol to set the size of __system_reset_overlay.  The
   assembler will then emit an error if the overlay code is too big.
 o Remove some unused instructions.
 o Update the text describing the PS3 bootwrapper overlay.
 o Add a check for null pointer writes.
 o Change hcall return value from s64.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards.  I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig.  There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html

Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image
with a fdt blob which means for any given configuration only one dts
file can be selected and so support for only one board can be built

This moves the selection of the default .dts file out of the kernel
config and into the bootwrapper makefile.  The makefile chooses which
images to build based on the kernel config and the dts source file
name is taken directly from the image name.  For example "cuImage.ebony"
will use "ebony.dts" as the device tree source file.

In addition, this patch allows a specific image to be requested from the
command line by adding "cuImage.%" and "treeImage.%" targets to the list
of valid built targets in arch/powerpc/Makefile.  This allows the default
dts selection to be overridden.

Another advantage to this change is it allows a single defconfig to be
supplied for all boards using the same chip family and only differing in
the device tree.

Important note: This patch adds two new zImage targets; zImage.dtb.% and
zImage.dtb.initrd.% for zImages with embedded dtb files.  Currently
there are 5 platforms which require this: ps3, ep405, mpc885ads, ep88xc,
adder875-redboot and ep8248e.  This patch *changes the zImage filenames*
for those platforms.  ie. 'zImage.ps3' is now 'zImage.dtb.ps3'.

This new zImage.dtb targets were added so that the .dts file could be
part of the dependancies list for building them.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.

This should work with both EP405 and EP405PC.

I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.

Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch.  It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It's possible that the executables which are built as helpers for the
bootwrapper stuff might end up in a different place to the intermediate
object files. Handle that.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If a .dts file is given to the bootwrapper script without a full path
name, look in a sensible place for it.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The bootwrapper script currently generates an 'otheros.bld' file in
addition to the file specified by the -o option, when asked to build a
wrapper for PS3.

It should do that in the same directory as the output, not the directory
where the wrapper objects are kept (which might potentially not be
writable when the script runs).

Arguably, the 'otheros.bld' ought to be created with the filename
specified as the -o argument. But that's a more intrusive change.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ps3 target produces two images, and the binary one is not the
"primary" image that corresponds to the -o flag; thus, it no longer
uses the generic binary flag.

On platforms which do use the binary flag, it no longer produces a
.bin suffix, so that the output file matches what was passed to the -o flag.

This should fix the zImage ln problems for the ps3 target.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add the 'set -e' command to the wrapper script so that if any command
fails then the script will automatically exit
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Allow wrapper script to print verbose progress when the V is set in the
environment.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support to build the PS3 flash rom image and remove some unneeded
lmb calls.

The PS3's lv1 loader supports loading gzipped binary images from flash
rom to addr zero. The loader enters the image at addr 0x100.

In this implementation a bootwrapper overlay is use to arrange for the
kernel to be loaded to addr zero and to have a suitable bootwrapper
entry at 0x100.  To construct the rom image, 0x100 bytes from offset
0x100 in the kernel is copied to the bootwrapper symbol
__system_reset_kernel.  The 0x100 bytes at the bootwrapper symbol
__system_reset_overlay is then copied to offset 0x100.  At runtime the
bootwrapper program copies the 0x100 bytes at __system_reset_kernel to
addr 0x100.

zImage.ps3 is a wrapped image that contains a flat device tree, an lv1
compatible entry point, and an optional initrd.  otheros.bld is the gzip
compresed rom image built from zImage.ps3.  otheros.bld is suitable for
programming into the PS3 boot flash memory.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Commit 9da82a6d inadvertently
removed the platform override for zImage.coff to be generated
with pmaccoff.   Rather than add a special makefile rule,
change the platform for which the wrapper platform uses
the special rules.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds platform support code for the Ebony (440GP) evaluation
board.  This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware.  The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch makes a few small cleanups to the cuboot code.
	- It removes the double layered selection of images, via
cuboot-plat-y, instead having the cuboot platforms directly select a
suitable image-y (this changes the name of the final cuboot image from
plain cuImage to cuImage.<platform>).
	- Factors out some code in the wrapper that's potentially
useful to platforms other than uboot.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The cuImage target will build a uImage with bootwrapper code and a device
tree.  The default device tree and platform file are determined by the
kernel configuration.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Commit a9903811 missed two uses of the
the .gz suffix in the wrapper script and didn't clean the additonal
possibly cached files.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The --no-gzip option can be passed to the wrapper so that the kernel
image is included uncompressed into the zImage.  This is intended for
bootloaders where the zImage itself can be compressed, or where boot time
is considered more important than kernel image size.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch re-organises the way the zImage wrapper code is entered, to
allow more flexibility on platforms with unusual entry conditions.
After this patch, a platform .o file has two options:

1) It can define a _zimage_start, in which case the platform code gets
   control from the very beginning of execution.  In this case the
   platform code is responsible for relocating the zImage if necessary,
   clearing the BSS, performing any platform specific initialization, and
   finally calling start() to load and enter the kernel.

2) It can define platform_init().  In this case the generic crt0.S
   handles initial entry, and calls platform_init() before calling
   start().  The signature of platform_init() is changed, however, to
   take up to 5 parameters (in r3..r7) as they come from the platform's
   initial loader, instead of a fixed set of parameters based on OF's
   usage.

   When using the generic crt0.S, the platform .o can optionally
   supply a custom stack to use, using the BSS_STACK() macro.  If this
   is not supplied, the crt0.S will assume that the loader has
   supplied a usable stack.

In either case, the platform code communicates information to the
generic code (specifically, a PROM pointer for OF systems, and/or an
initrd image address supplied by the bootloader) via a global
structure "loader_info".

In addition the wrapper script is rearranged to ensure that the
platform .o is always linked first.  This means that platforms where
the zImage entry point is at a fixed address or offset, rather than
being encoded in the binary header can be supported using option (1).
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

When the wrapper script is passed a dts file, it runs 'dtc' to create
a dtb file.  This patch deletes that dtb file once its no longer needed.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The "wrapper" script was using the wrong names for the initrd and
dtb (device-tree blob) sections.  This fixes it, and also ensures
the symbols for the start and end of the dtb get defined correctly.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

More reorganization of the bootwrapper:
- Add dtb section to zImage
- ft_init now called by platform_init
- Pack a flat dt before calling kernel
- Remove size parameter from free
- printf only calls console_ops.write it its not NULL
- Some cleanup
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This puts the knowledge of how to create various sorts of zImage
wrappers into a script called "wrapper" that could be used outside of
the kernel tree.  This changes arch/powerpc/boot so it first builds
the files that the wrapper script needs, then runs it to create
whatever flavours of zImage are required.

This version does uImages as well.  The zImage names are changed
slightly; zImage.pseries is the one with the PT_NOTE program header
entry added, and zImage.pmac is the one without.  If the
zImage.pseries gets made, it will also get hardlinked to zImage;
otherwise, if zImage.pmac is made, it gets hardlinked to zImage.
Signed-off-by: NPaul Mackerras <paulus@samba.org>