The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver performs the internal reload when it receives tx-timeout event from
the OS. Internal reload might fail in some scenarios e.g., fatal HW issues.
In such cases OS still see the link, which would result in undesirable
functionalities such as re-generation of tx-timeouts.
The patch addresses this issue by indicating the link-down to OS when
tx-timeout is detected, and keeping the link in down state till the
internal reload is successful.

Please consider applying it to 'net' branch.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Static checkers complain that id_tbl->table points to longs and 4 bytes
is smaller than sizeof(long).  But the since other side is dividing by
32 instead of sizeof(long), that means the current code works fine.

Anyway, it's more conventional to use the BITS_TO_LONGS() macro when
we're allocating a bitmap.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is clearly a bug.

We need to set the DMA buffer size in the HW otherwise corruption can
occur when receiving packets.

This is probably not occuring because of small MTU values and because HW
has a default value internally (which currently is bigger than default
buffer size).
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was combining XDP_TX virtqueue_kick and XDP_REDIRECT
map flushing (xdp_do_flush_map).  This is suboptimal, these two
flush operations should be kept separate.

The suboptimal behavior was introduced in commit 9267c430
("virtio-net: add missing virtqueue kick when flushing packets").

Fixes: 9267c430 ("virtio-net: add missing virtqueue kick when flushing packets")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map).  This is suboptimal, these two
flush operations should be kept separate.

It looks like the mistake was copy-pasted from ixgbe.

Fixes: d9314c47 ("i40e: add support for XDP_REDIRECT")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NBjörn Töpel <bjorn.topel@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map).  This is suboptimal, these two
flush operations should be kept separate.

Fixes: 11393cc9 ("xdp: Add batching support to redirect map")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macb driver currently crashes on at91rm9200 with the following trace:

Unable to handle kernel NULL pointer dereference at virtual address 00000014
[...]
[<c031da44>] (macb_rx_desc) from [<c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<c031f2bc>] (at91ether_open) from [<c041e8d8>] (__dev_open+0x120/0x13c)
[<c041e8d8>] (__dev_open) from [<c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<c041ec08>] (__dev_change_flags) from [<c041ec4c>] (dev_change_flags+0x18/0x4c)
[<c041ec4c>] (dev_change_flags) from [<c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<c07a5f4c>] (ip_auto_config) from [<c000a4fc>] (do_one_initcall+0x78/0x18c)
[<c000a4fc>] (do_one_initcall) from [<c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<c0783e50>] (kernel_init_freeable) from [<c0574d70>] (kernel_init+0x8/0xe8)
[<c0574d70>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)

Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).

Fixes: ae1f2a56 ("net: macb: Added support for many RX queues")
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following warning is seen when rmmod hinic. This is because affinity
value is not reset before calling free_irq(). This patch fixes it.

[   55.181232] WARNING: CPU: 38 PID: 19589 at kernel/irq/manage.c:1608
__free_irq+0x2aa/0x2c0

Fixes: 352f58b0 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sizeof() will return unsigned value so in the error check
negative error code will be always larger than sizeof().

Fixes: a0d8e02c ("nfp: add support for reading nffw info")
Signed-off-by: NChengguang Xu <cgxu519@gmx.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TC shared blocks allow multiple qdiscs to be grouped together and filters
shared between them. Currently the chains of filters attached to a block
are only flushed when the block is removed. If a qdisc is removed from a
block but the block still exists, flow del messages are not passed to the
callback registered for that qdisc. For the NFP, this presents the
possibility of rules still existing in hw when they should be removed.

Prevent binding to shared blocks until the kernel can send per qdisc del
messages when block unbinds occur.

tcf_block_shared() was not used outside of the core until now, so also
add an empty implementation for builds with CONFIG_NET_CLS=n.

Fixes: 48617387 ("net: sched: introduce shared filter blocks infrastructure")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously it was not possible to distinguish between mpls ether types and
other ether types. This leads to incorrect classification of offloaded
filters that match on mpls ether type. For example the following two
filters overlap:

 # tc filter add dev eth0 parent ffff: \
    protocol 0x8847 flower \
    action mirred egress redirect dev eth1

 # tc filter add dev eth0 parent ffff: \
    protocol 0x0800 flower \
    action mirred egress redirect dev eth2

The driver now correctly includes the mac_mpls layer where HW stores mpls
fields, when it detects an mpls ether type. It also sets the MPLS_Q bit to
indicate that the filter should match mpls packets.

Fixes: bb055c19 ("nfp: add mpls match offloading support")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.

When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.

Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.

mlx5_unload_one()
        mlx5_stop_eqs()
                // Destroy the EQ before cmd EQ
                ...cmd_work_handler()
                        write_doorbell()
                        --> EVENT_TYPE_CMD
                                mlx5_cmd_comp_handler() // First free
                                        free_ent(cmd, ent->idx)
                                        complete(&ent->done)

        <-- mlx5_stop_eqs //cmd was complete
                // move to polling before destroying the last cmd EQ
                mlx5_cmd_use_polling()
                        cmd->mode = POLL;

                --> cmd_work_handler (continues)
                        if (cmd->mode == POLL)
                                mlx5_cmd_comp_handler() // Double free

The solution is to store the cmd->mode before writing the doorbell.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.

Fixes: e126ba97 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The driver allocates wrong size (due to wrong struct name) when issuing
a query/set request to NIC's register.

Fixes: d8880795 ("net/mlx5e: Implement DCBNL IEEE max rate")
Signed-off-by: NShay Agroskin <shayag@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Manipulating of the MPFS requires eswitch manager capabilities.

Fixes: eeb66cdb ('net/mlx5: Separate between E-Switch and MPFS')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In smartnic env, if the host (PF) driver is not an e-switch manager, we
are not allowed to apply eswitch ports setups such as vlan (VST),
spoof-checks, min/max rate or state.

Make sure we are eswitch manager when coming to issue these callbacks
and err otherwise.

Also fix the definition of ESW_ALLOWED to rely on eswitch_manager
capability and on the vport_group_manger.

Operations on the VF nic vport context, such as setting a mac or reading
the vport counters are allowed to the PF in this scheme.

The modify nic vport guid code was modified to omit checking the
nic_vport_node_guid_modify eswitch capability.
The reason for doing so is that modifying node guid requires vport group
manager capability, and there's no need to check further capabilities.

1. set_vf_vlan     - disallowed
2. set_vf_spoofchk - disallowed
3. set_vf_mac      - allowed
4. get_vf_config   - allowed
5. set_vf_trust    - disallowed
6. set_vf_rate     - disallowed
7. get_vf_stat     - allowed
8. set_vf_link_state - disallowed

Fixes: f942380c ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: NEli Cohen <eli@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Tested-by: NOr Gerlitz <ogerlitz@mellanox.com>

In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.

As such, we should avoid dealing with vport representors if
not being esw manager.

While here, make sure to disallow eswitch switchdev related
setups through devlink if we are not esw managers.

Fixes: cb67b832 ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the FW will err on driver attempts to deal with
setting/unsetting the eswitch and as a result the overall setup
of sriov will fail.

Fix that by avoiding the operation if e-switch management is not
allowed for this driver instance. While here, move to use the
correct name for the esw manager capability name.

Fixes: 81848731 ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NGuy Kushnir <guyk@mellanox.com>
Reviewed-by: NEli Cohen <eli@melloanox.com>
Tested-by: NEli Cohen <eli@melloanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The check for cpu hit statistics was not returning immediate false for
any non vport rep netdev and hence we crashed (say on mlx5 probed VFs) if
user-space tool was calling into any possible netdev in the system.

Fix that by doing a proper check before dereferencing.

Fixes: 1d447a39 ('net/mlx5e: Extendable vport representor netdev private data')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NEli Cohen <eli@melloanox.com>
Reviewed-by: NEli Cohen <eli@melloanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Observations of VLANs dropping packets due to invalid
checksums when not offloading VLAN tag receive.
With VLAN tag stripping enabled no issue is observed.

Drop back to s/w checksums if VLAN offload is disabled.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports stripping the VLAN tag and reporting it
in metadata.
Complete the support for this.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW_VLAN_CTAG_FILTER was partially implemented, but not advertised
to Linux.

Complete the implementation of this.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.

Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable.  usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.

So avoid the call to napi_disable in rtl8152_close when the device is
already gone.

The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function efx_rps_hash_bucket is local to the source and
does not need to be in global scope, so make it static.

Cleans up sparse warning:
symbol 'efx_rps_hash_bucket' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.

By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we are disabling DCB, store "0" in txq->dcb_prio
since that's used for future TX Work Request "OVLAN_IDX"
values. Setting non zero priority upon disabling DCB
would halt the traffic.
Reported-by: NAMG Zollner Robert <robert@cloudmedia.eu>
CC: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NMark Brown <broonie@kernel.org>
Acked-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a sparse warning about using an incorrect type in
argument 2 of ocelot_write_rix(), as an u32 was expected but a __be32
was given. The conversion to u32 is forced, which is safe as the value
will be written as-is in the hardware without any modification.

Fixes: 08d02364 ("net: mscc: fix the injection header")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using s/w buffer management, buffers are allocated and DMA mapped.
When doing so on an arm64 platform, an offset correction is applied on
the DMA address, before storing it in an Rx descriptor. The issue is
this DMA address is then used later in the Rx path without removing the
offset correction. Thus the DMA address is wrong, which can led to
various issues.

This patch fixes this by removing the offset correction from the DMA
address retrieved from the Rx descriptor before using it in the Rx path.

Fixes: 8d5047cf ("net: mvneta: Convert to be 64 bits compatible")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function cpdma_desc_pool_create is local to the source and does not
need to be in global scope, so make it static.

Cleans up sparse warning:
warning: symbol 'cpdma_desc_pool_create' was not declared. Should it
be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the features after calling register_netdev() otherwise the
device features are not set up correctly and it not possible to change
the MTU of the device. After this change, the features reported by
ethtool match the device's features before the commit which introduced
the issue and it is possible to change the device's MTU.

Fixes: f599c64f ("xen-netfront: Fix race between device setup and open")
Reported-by: NLiam Shepherd <liam@dancer.es>
Signed-off-by: NRoss Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: f599c64f ("xen-netfront: Fix race between device setup and open")
Reported-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NRoss Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When delta passed to gem_ptp_adjtime is negative, the sign is
maintained in the ns_to_timespec64 conversion. Hence timespec_add
should be used directly. timespec_sub will just subtract the negative
value thus increasing the time difference.
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 296d4856 ("ipvlan: inherit MTU from master device") adjusted
the mtu from the master device when creating a ipvlan device, but it
would also override the mtu value set in rtnl_create_link. It causes
IFLA_MTU param not to take effect.

So this patch is to not adjust the mtu if IFLA_MTU param is set when
creating a ipvlan device.

Fixes: 296d4856 ("ipvlan: inherit MTU from master device")
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When injecting frames in the Ocelot switch driver an injection header
(IFH) should be used to configure various parameters related to a given
frame, such as the port onto which the frame should be departed or its
vlan id. Other parameters in the switch configuration can led to an
injected frame being sent without an IFH but this led to various issues
as the per-frame parameters are then not used. This is especially true
when using multiple ports for injection.

The IFH was injected with the wrong endianness which led to the switch
not taking it into account as the IFH_INJ_BYPASS bit was then unset.
(The bit tells the switch to use the IFH over its internal
configuration). This patch fixes it.

In addition to the endianness fix, the IFH is also fixed. As it was
(unwillingly) unused, some of its fields were not configured the right
way.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device tree based systems without of_dev_auxdata will have the mdio
device named differently than "davinci_mdio(.0)". In this case use the
device's parent's compatible string for matching
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the correct thing to rtl8169_interrupt() from netpoll.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: netdev@vger.kernel.org
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: ebcd5daa ("r8169: change interrupt handler argument type")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>