This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().

Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.

24       25       12 48000000   64000000   4000000(1)
49       50       14 49000000   56000000   3500000(1)
4        5        16 40000000   40000000   2500000(1)
16       25       16 32000000   32000000   500000(4),1000000(2),2000000(1)
24       25       16 48000000   48000000   1500000(2),3000000(1)
2304     3125     16 36864000   36864000   576000(4),1152000(2)
8192     15625    16 26214400   26214400   50(32768),200(8192)
9216     15625    16 29491200   29491200   1800(1024),57600(32),115200(16),
					230400(8),460800(4),921600(2),1843200(1)
12288    15625    16 39321600   39321600   75(32768),150(16384),300(8192),
					600(4096),1200(2048),2400(1024),4800(512),
					9600(256),19200(128),38400(64)
45056    78125    16 28835840   28835840   110(16384)
274432   390625   16 35127296   35127296   134(16384)
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for byt_set_termios().

Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) numerator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.

4        5        16 80000000   80000000   2500000(2)
14       25       16 56000000   56000000   3500000(1)
16       25       16 64000000   64000000   500000(8),1000000(4),2000000(2),
					4000000(1)
24       25       16 96000000   96000000   1500000(4),3000000(2)
2180     3103     16 70254592   70254592   134(32768)
2304     3125     16 73728000   73728000   576000(8),1152000(4)
8192     15625    16 52428800   52428800   50(65536),200(16384)
9216     15625    16 58982400   58982400   1800(2048),57600(64),115200(32),
					230400(16),460800(8),921600(4),1843200(2)
12288    15625    16 78643200   78643200   75(65536),150(32768),300(16384),
					600(8192),1200(4096),2400(2048),
					4800(1024),9600(512),19200(256),38400(128)
9893     17154    16 57671680   57671680   110(32768)
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove pci_fintek_setup() non-used var with calculation ciobase
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Penwell supports 3 HSUART ports which are 8250 compatible. The patch adds
necessary bits to the driver.

The functions have intel_mid_* prefix due to more than one platform will use
this code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redudant calls to the PCI for changing a power state since it's done by bus
code.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These quirk entries have the same effect as default
quirk entry, so we can just delete them.
Signed-off-by: NWang YanQing <udknight@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 8b5c913f
("serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection")
trigger one redundant entry report message.

This patch fix it.
Reported-by: NRussell King <rmk@arm.linux.org.uk>
Signed-off-by: NWang YanQing <udknight@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.

Cc: <stable@vger.kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

WCH384 4S board is a PCI-E card with 4 DB9 COM ports detected as
Serial controller: Device 1c00:3470 (rev 10) (prog-if 05 [16850])
Signed-off-by: NSergej Pupykin <ml@sergej.pp.ru>
Acked-by: NZany Yan <sirlight@cox.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The original driver fixed the io address with 0xe000+idx*8,
but real io address assigned from BIOS is dynamically from
read PCI configure space 0x24, 0x20, 0x1c.

The Fintek F81504/F81508/F81512 maybe malfunction without
this patch and malfunction surely when more then 1 PCI card.
Signed-off-by: NPeter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

WCH382 is a PCI-E card with 1 LPT and 2 DB9 COM ports detected as
Serial controller: Device 1c00:3250 (rev 10) (prog-if 05 [16850])
Signed-off-by: NSergej Pupykin <ml@sergej.pp.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Check the return value of ioremap_nocache to make sure we got a
valid mapping.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Several init/setup functions passed the PCI BAR resource start address
to ioremap_nocache() via an unsigned long. This caused address truncation
for a 32-bit device mapped above 4 GiB (i.e. the CPU interacts with the
device via a translated address), which resulted in a kernel panic.

This patch replaces all of the instances of intermediate variable use
with pci_ioremap_bar() to ensure the full resource_size_t start address
is used and that ioremap_nocache() is still called.

The kernel panic (Exar XR17V358 PCIe device on a Freescale P2020 SBC):

Machine check in kernel mode.
Caused by (from MCSR=10008): Bus - Read Data Bus Error
Oops: Machine check, sig: 7 [#1]
SMP NR_CPUS=2 X-ES P2020
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14.15-xes_r2-00002-g560e401 #978
task: bf850000 ti: bffee000 task.ti: bf84c000
NIP: 80318e10 LR: 80319ecc CTR: 80318dfc
REGS: bffeff10 TRAP: 0204   Not tainted  (3.14.15-xes_r2-00002-g560e401)
MSR: 00021000 <CE,ME>  CR: 20adbe42  XER: 00000000
DEAR: c1058001 ESR: 00000000
GPR00: 00000000 bf84db30 bf850000 80cb4af8 00000001 00000000 80000007 80000000
GPR08: bf837c9c c1058001 00000001 00000000 80000007 00000000 80002a10 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 80cb0000 80c72dc4
GPR24: 80cb4900 fffffffe 00029000 00000001 bf8c11e8 ffffffea 80c72ce4 80cb4af8
NIP [80318e10] mem_serial_in+0x14/0x28
LR [80319ecc] serial8250_config_port+0x160/0xe38
Call Trace:
[bf84db30] [80319d94] serial8250_config_port+0x28/0xe38 (unreliable)
[bf84db60] [80315e3c] uart_add_one_port+0x148/0x3a4
[bf84dbf0] [8031bf40] serial8250_register_8250_port+0x2dc/0x3c8
[bf84dc20] [8032111c] pciserial_init_ports+0xd4/0x1c0
[bf84dd50] [803212f8] pciserial_init_one+0xf0/0x224
[bf84dd90] [802d8ff4] local_pci_probe+0x34/0x8c
[bf84dda0] [802d92c8] pci_device_probe+0x84/0xa0
[bf84ddc0] [80329ee0] driver_probe_device+0xac/0x26c
[bf84dde0] [8032a15c] __driver_attach+0xbc/0xc0
[bf84de00] [80328388] bus_for_each_dev+0x90/0xcc
[bf84de30] [80329cd0] driver_attach+0x24/0x34
[bf84de40] [80328e28] bus_add_driver+0x104/0x1fc
[bf84de60] [8032a8c8] driver_register+0x70/0x138
[bf84de70] [802d93c0] __pci_register_driver+0x48/0x58
[bf84de80] [8077e0e4] serial_pci_driver_init+0x24/0x34
[bf84de90] [80002228] do_one_initcall+0x34/0x1b0
[bf84df00] [80764294] kernel_init_freeable+0x138/0x1e8
[bf84df30] [80002a24] kernel_init+0x14/0x108
[bf84df40] [8000ef94] ret_from_kernel_thread+0x5c/0x64
Instruction dump:
800800c4 7d290214 39290001 7c0004ac 7ca049ae 7c0004ac 4e800020 88030035
81230008 7c840030 7d292214 7c0004ac <88690000> 0c030000 4c00012c 5463063e
---[ end trace e3c16443b5d573c6 ]---
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Added recognition of EndRun Technologies PCIe PTP slave card
and setup two ttySx ports for communication with the card for
retrieval of PTP based time and to communicate with the card's
Linux OS.
Signed-off-by: NMike Skoog <mskoog@endruntechnologies.com>
Signed-off-by: NMike Korreng <mkorreng@endruntechnologies.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It should not be used together with Auto Flow Control, and
Auto Flow Control is always enabled on Baytrail.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.

Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.

This patch enables standard 8250 mode
Signed-off-by: NBryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new PCI IDs to cover newer Intel SoCs such as Braswell.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

That field has been deprecated in favour of getting the necessary information
from ACPI or DT.

However, we still need to deal systems that are PCI only (no ACPI to back up)
like Intel Bay Trail. In order to support such systems, we explicitly bind
setup() to the appropriate DMA filter function and its corresponding parameter.
Then when serial8250_request_dma() doesn't find the channel via ACPI or DT, it
falls back to use the given filter function.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for Advantech PCM-3614I/PCM-3618I serial expansion cards

Advantech makes a variety of serial port expansion cards, including the
PCM-3614 and PCM-3618
(http://www.advantech.com/products/1-2JKLU5/PCM-3618/mod_5DF8DE5A-6B49-4429-BB2F-CB35FE1D168D.aspx).
They have a driver available which was forked from the kernel driver
ages ago and has not been maintained in quite some time, available at
http://support.advantech.com.tw/Support/DownloadSRDetail_New.aspx?SR_ID=1-1W8FZ5&Doc_Source=Download
Their driver added several features to aid in communications at higher
baud rates, but at normal serial port speeds, the standard 8250_pci
driver functions just fine. This patch adds the necessary PCI IDs to
recognize this card.

See bug 75681 (https://bugzilla.kernel.org/show_bug.cgi?id=75681)
Signed-off-by: NThomee Wright <TWright@TMCDesign.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:

03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
	Subsystem: Device 4348:5053
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at cf00 [size=8]
	Region 1: I/O ports at ce00 [size=8]
	Kernel driver in use: parport_serial
	Kernel modules: 8250_pci, parport_serial

This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.

Proper entries are added to parport_serial, to support the device parallel
and serial ports.

Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Intel BayTrail HSUART power-on default reference clock is 44.2368 MHz,
but 73.728 MHz provides 0% error for additional "conventional" baud rates
above 460800 (e.g. 576000, 921600, and 1152000).
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Support the following additional baud rates with 0% error:
	500000, 1500000, 2500000, 3500000
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Aparently 9865 uses standard BAR encoding scheme (unlike 99xx cards).
Current pci_netmos_9900_setup() uses wrong BAR indices for the 9865 PCI
device, function 2. Using standard BAR indices makes all 6 ports work
for me. Thus disable the NetMos 9900 quirk for NetMos 9865 pci device.

For the reference, here is the relevant part of lspci for my device:

02:07.0 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
	Subsystem: Device a000:1000
	Flags: bus master, medium devsel, latency 32, IRQ 17
	I/O ports at ac00 [size=8]
	Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
	Memory at fcffe000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [48] Power Management version 2
	Kernel driver in use: serial

02:07.1 Serial controller: MosChip Semiconductor Technology Ltd. PCI
9865 Multi-I/O Controller (prog-if 02 [16550])
	Subsystem: Device a000:1000
	Flags: bus master, medium devsel, latency 32, IRQ 18
	I/O ports at a800 [size=8]
	Memory at fcffd000 (32-bit, non-prefetchable) [size=4K]
	Memory at fcffc000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [48] Power Management version 2
	Kernel driver in use: serial

02:07.2 Communication controller: MosChip Semiconductor Technology Ltd.
PCI 9865 Multi-I/O Controller
	Subsystem: Device a000:3004
	Flags: bus master, medium devsel, latency 32, IRQ 19
	I/O ports at a400 [size=8]
	I/O ports at a000 [size=8]
	I/O ports at 9c00 [size=8]
	I/O ports at 9800 [size=8]
	Memory at fcffb000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [48] Power Management version 2
	Kernel driver in use: serial
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.

Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.

Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NAngelo Butti <buttiangelo@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.

Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.

Cc: Amanda Ying <amanda_ying@fintek.com.tw>
Cc: Felix Shih <felix_shih@fintek.com.tw>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the printk() calls to to dev_*() instead, to tie into the dynamic
debugging infrastructure.

Also change some "raw" printk() calls to dev_err() to provide a better
error message to userspace so it can properly identify the device and
not just have to guess.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel BayTrail has two HS-UARTs with 64 byte fifo, support
for DMA and support for 16750 compatible Auto Flow Control.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The quirks and PCI ID table entries for the original ADDI-DATA APCI-7800
(not the newer APCI-7800-3) use PCI_DEVICE_ID_ADDIDATA_APCI7800 from
<linux/pci_ids.h> but the device ID was actually assigned to ADDI-DATA
by Applied Micro Circuits Corporation (PCI_VENDOR_ID_AMCC).  Replace it
locally with #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI_VENDOR_ID_ADDIDATA_OLD has the same value (0x10e8) as
PCI_VENDOR_ID_AMCC in <linux/pci_ids.h>.  The vender ID is actually
assigned to Applied Micro Circuits Corporation.  The 8250_pci driver
uses PCI_VENDOR_ID_ADDIDATA_OLD in the lists of quirks and PCI IDs for
the ADDI-DATA APCI-7800 card.  Change it to use the more accurate
PCI_VENDOR_ID_AMCC.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: NStefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller"

This reverts commit 8d2f8cd4.

As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: NStefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The code in 8250.c for detecting ARM/XScale UARTs says:

  * Try writing and reading the UART_IER_UUE bit (b6).
  * If it works, this is probably one of the Xscale platform's
  * internal UARTs.

If the above passes, it then goes on to:

     * It's an Xscale.
     * We'll leave the UART_IER_UUE bit set to 1 (enabled).

However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable.  According to the datasheet:

    "LOWPOWER:When the bit is 1, close the internal benchmark
     clock of serial port to set into low-power status.

So it essentially gets mis-detected as Xscale, and gets
powered down in the process.  The device in question where
this was seen is listed by lspci as:

 Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])

Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.
Signed-off-by: NWang YanQing <udknight@gmail.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

01:08.0 Communication controller: NetMos Technology PCI 9835 Multi-I/O Controller (rev 01)
	Subsystem: Device [1000:0012]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 20
	Region 0: I/O ports at e050 [size=8]
	Region 1: I/O ports at e040 [size=8]
	Region 2: I/O ports at e030 [size=8]
	Region 3: I/O ports at e020 [size=8]
	Region 4: I/O ports at e010 [size=8]
	Region 5: I/O ports at e000 [size=16]
Signed-off-by: NWang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>