Today, driver drops received packets which are indicated as
invalid checksum by the device. Instead of dropping such packets,
pass them to the stack with CHECKSUM_NONE indication in skb.
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My recent change to netvsc drive in how receive flags are handled
broke multicast.  The Hyper-v/Azure virtual interface there is not a
multicast filter list, filtering is only all or none. The driver must
enable all multicast if any multicast address is present.

Fixes: 009f766c ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We want to use dev_set_mtu() regardless of how we calculate
the mtu value.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.

Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.

Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2018-03-29

1) Fix a rcu_read_lock/rcu_read_unlock imbalance
   in the error path of xfrm_local_error().
   From Taehee Yoo.

2) Some VTI MTU fixes. From Stefano Brivio.

3) Fix a too early overwritten skb control buffer
   on xfrm transport mode.

Please note that this pull request has a merge conflict
in net/ipv4/ip_tunnel.c.

The conflict is between

commit f6cc9c05 ("ip_tunnel: Emit events for post-register MTU changes")

from the net tree and

commit 24fc7979 ("ip_tunnel: Clamp MTU to bounds on new link")

from the ipsec tree.

It can be solved as it is currently done in linux-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit c5ad119f
("net: sched: pfifo_fast use skb_array") driver is exposed
to an issue where it is hitting NULL skbs while handling TX
completions. Driver uses mmiowb() to flush the writes to the
doorbell bar which is a write-combined bar, however on x86
mmiowb() does not flush the write combined buffer.

This patch fixes this problem by replacing mmiowb() with wmb()
after the write combined doorbell write so that writes are
flushed and synchronized from more than one processor.

V1->V2:
-------
This patch was marked as "superseded" in patchwork.
(Not really sure for what reason).Resending it as v2.
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We tried to remove vq poll from wait queue, but do not check whether
or not it was in a list before. This will lead double free. Fixing
this by switching to use vhost_poll_stop() which zeros poll->wqh after
removing poll from waitqueue to make sure it won't be freed twice.

Cc: Darren Kenny <darren.kenny@oracle.com>
Reported-by: syzbot+c0272972b01b872e604a@syzkaller.appspotmail.com
Fixes: 2b8b328b ("vhost_net: handle polling errors when setting backend")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NDarren Kenny <darren.kenny@oracle.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4 misc fixes for 4.16

This patchset contains misc bug fixes from the team
to the mlx4 Core and Eth drivers.

Patch 1 by Eran fixes a control mix of PFC and Global pauses, please queue it
to -stable for >= v4.8.
Patch 2 by Moshe fixes a resource leak in slave's delete flow, please queue it
to -stable for >= v4.5.

Series generated against net commit:
3c82b372 net: dsa: mt7530: fix module autoloading for OF platform drivers
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4_delete_all_resources_for_slave in resource tracker should free all
memory allocated for a slave.
While releasing memory of fs_rule, it misses releasing memory of
fs_rule->mirr_mbox.

Fixes: 78efed27 ('net/mlx4_core: Support mirroring VF DMFS rules on both ports')
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Global pause and PFC configuration should be mutually exclusive (i.e. only
one of them at most can be set). However, once PFC was turned off,
driver automatically turned Global pause on. This is a bug.

Fix the driver behaviour to turn off PFC/Global once the user turned the
other on.

This also fixed a weird behaviour that at a current time, the profile
had both PFC and global pause configuration turned on, which is
Hardware-wise impossible and caused returning false positive indication
to query tools.

In addition, fix error code when setting global pause or PFC to change
metadata only upon successful change.

Also, removed useless debug print.

Fixes: af7d5185 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not every CLC proposal message needs the maximum buffer length.
Due to the MSG_WAITALL flag, it is important to use the peeked
real length when receiving the message.

Fixes: d63d271c ("smc: switch to sock_recvmsg()")
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

llc_conn_send_pdu() pushes the skb into write queue and
calls llc_conn_send_pdus() to flush them out. However, the
status of dev_queue_xmit() is not returned to caller,
in this case, llc_conn_state_process().

llc_conn_state_process() needs hold the skb no matter
success or failure, because it still uses it after that,
therefore we should hold skb before dev_queue_xmit() when
that skb is the one being processed by llc_conn_state_process().

For other callers, they can just pass NULL and ignore
the return value as they are.
Reported-by: NNoam Rathaus <noamr@beyondsecurity.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-03-23

The following series includes fixes for mlx5 netdev and eswitch.

v1->v2:
    - Fixed commit message quotation marks in patch #7

For -stable v4.12
    ('net/mlx5e: Avoid using the ipv6 stub in the TC offload neigh update path')
    ('net/mlx5e: Fix traffic being dropped on VF representor')

For -stable v4.13
    ('net/mlx5e: Fix memory usage issues in offloading TC flows')
    ('net/mlx5e: Verify coalescing parameters in range')

For -stable v4.14
    ('net/mlx5e: Don't override vport admin link state in switchdev mode')

For -stable v4.15
    ('108b2b6d5c02 net/mlx5e: Sync netdev vxlan ports at open')

Please pull and let me know if there's any problem.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

strp_parser_err is called with a negative code everywhere, which then
calls abort_parser with a negative code.  strp_msg_timeout calls
abort_parser directly with a positive code.  Negate ETIMEDOUT
to match signed-ness of other calls.

The default abort_parser callback, strp_abort_strp, sets
sk->sk_err to err.  Also negate the error here so sk_err always
holds a positive value, as the rest of the net code expects.  Currently
a negative sk_err can result in endless loops, or user code that
thinks it actually sent/received err bytes.

Found while testing net/tls_sw recv path.

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Signed-off-by: NDave Watson <davejwatson@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes a bug in the tcf_dump_walker function that can cause some actions
to not be reported when dumping a large number of actions. This issue
became more aggrevated when cookies feature was added. In particular
this issue is manifest when large cookie values are assigned to the
actions and when enough actions are created that the resulting table
must be dumped in multiple batches.

The number of actions returned in each batch is limited by the total
number of actions and the memory buffer size.  With small cookies
the numeric limit is reached before the buffer size limit, which avoids
the code path triggering this bug. When large cookies are used buffer
fills before the numeric limit, and the erroneous code path is hit.

For example after creating 32 csum actions with the cookie
aaaabbbbccccdddd

$ tc actions ls action csum
total acts 26

    action order 0: csum (tcp) action continue
    index 1 ref 1 bind 0
    cookie aaaabbbbccccdddd

    .....

    action order 25: csum (tcp) action continue
    index 26 ref 1 bind 0
    cookie aaaabbbbccccdddd
total acts 6

    action order 0: csum (tcp) action continue
    index 28 ref 1 bind 0
    cookie aaaabbbbccccdddd

    ......

    action order 5: csum (tcp) action continue
    index 32 ref 1 bind 0
    cookie aaaabbbbccccdddd

Note that the action with index 27 is omitted from the report.

Fixes: 4b3550ef ("[NET_SCHED]: Use nla_nest_start/nla_nest_end")"
Signed-off-by: NCraig Dillabaugh <cdillaba@mojatatu.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_set_drvdata() is called only after registering the net_device,
therefore we could run into a NPE if one of the functions using
driver_data is called before it's set.

Fix this by calling pci_set_drvdata() before registering the
net_device.

This fix is a candidate for stable. As far as I can see the
bug has been there in kernel version 3.2 already, therefore
I can't provide a reference which commit is fixed by it.

The fix may need small adjustments per kernel version because
due to other changes the label which is jumped to if
register_netdev() fails has changed over time.
Reported-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb mac header is not necessarily set at the time skb_network_protocol()
is called. Use skb->data instead.

BUG: KASAN: slab-out-of-bounds in skb_network_protocol+0x46b/0x4b0 net/core/dev.c:2739
Read of size 2 at addr ffff8801b3097a0b by task syz-executor5/14242

CPU: 1 PID: 14242 Comm: syz-executor5 Not tainted 4.16.0-rc6+ #280
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x194/0x24d lib/dump_stack.c:53
 print_address_description+0x73/0x250 mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report+0x23c/0x360 mm/kasan/report.c:412
 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/report.c:443
 skb_network_protocol+0x46b/0x4b0 net/core/dev.c:2739
 harmonize_features net/core/dev.c:2924 [inline]
 netif_skb_features+0x509/0x9b0 net/core/dev.c:3011
 validate_xmit_skb+0x81/0xb00 net/core/dev.c:3084
 validate_xmit_skb_list+0xbf/0x120 net/core/dev.c:3142
 packet_direct_xmit+0x117/0x790 net/packet/af_packet.c:256
 packet_snd net/packet/af_packet.c:2944 [inline]
 packet_sendmsg+0x3aed/0x60b0 net/packet/af_packet.c:2969
 sock_sendmsg_nosec net/socket.c:629 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:639
 ___sys_sendmsg+0x767/0x8b0 net/socket.c:2047
 __sys_sendmsg+0xe5/0x210 net/socket.c:2081

Fixes: 19acc327 ("gso: Handle Trans-Ether-Bridging protocol in skb_network_protocol()")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@ovn.org>
Reported-by: NReported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This modem is embedded on dlink dwr-921 router.
    The oem configuration states:

    T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
    D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1435 ProdID=0918 Rev= 2.32
    S:  Manufacturer=Android
    S:  Product=Android
    S:  SerialNumber=0123456789ABCDEF
    C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
    I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
    E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
    E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
    E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=88(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
    E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution
Signed-off-by: NGiuseppe Lippolis <giu.lippolis@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are some batman-adv bugfixes:

 - fix multicast-via-unicast transmissions for AP isolation and gateway
   extension, by Linus Luessing (2 patches)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mlx5_core is loaded it is expected to sync ports
with all vxlan devices so it can support vxlan encap/decap.
This is done via udp_tunnel_get_rx_info(). Currently this
call is set in mlx5e_nic_enable() and if the netdev is not in
NETREG_REGISTERED state it will not be called.

Normally on load the netdev state is not NETREG_REGISTERED
so udp_tunnel_get_rx_info() will not be called.

Moving udp_tunnel_get_rx_info() to mlx5e_open() so
it will be called on netdev UP event and allow encap/decap.

Fixes: 610e89e0 ("net/mlx5e: Don't sync netdev state when not registered")
Signed-off-by: NShahar Klein <shahark@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently we use the global ipv6_stub var to access the ipv6 global
nd table. This practice gets us to troubles when the stub is only partially
set e.g when ipv6 is loaded under the disabled policy. In this case, as of commit
343d60aa ("ipv6: change ipv6_stub_impl.ipv6_dst_lookup to take net argument")
the stub is not null, but stub->nd_tbl is and we crash.

As we can access the ipv6 nd_tbl directly, the fix is just to avoid the
reference through the stub. There is one place in the code where we
issue ipv6 route lookup and keep doing it through the stub, but that
mentioned commit makes sure we get -EAFNOSUPPORT from the stack.

Fixes: 232c0013 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NAviv Heller <avivh@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

For NIC flows, the parsed attributes are not freed when we exit
successfully from mlx5e_configure_flower().

There is possible double free for eswitch flows. If error is returned
from rhashtable_insert_fast(), the parse attrs will be freed in
mlx5e_tc_del_flow(), but they will be freed again before exiting
mlx5e_configure_flower().

To fix both issues we do the following:
(1) change the condition that determines if to issue the free call to
    check if this flow is NIC flow, or it does not have encap action.
(2) reorder the code such that that the check and free calls are done
    before we attempt to add into the hash table.

Fixes: 232c0013 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Increase representor netdev RQ size to avoid dropped packets.
The current size (two) is just too small to keep up with
conventional slow path traffic patterns.
Also match the SQ size to the RQ size.

Fixes: cb67b832 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx5 modify cq limits the coalescing time parameter to 12 bit
and coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.

Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add dependancy for switchdev to be congfigured as any user-space control
plane SW is expected to use the HW switchdev ID to locate the representors
related to VFs of a certain PF and apply SW/offloaded switching on them.

Fixes: e80541ec ('net/mlx5: Add CONFIG_MLX5_ESWITCH Kconfig')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

SQs are 32 and not 16 bits, hence it's wrong to use only 16 bits to
store the sq number for which are going to set steering rule, fix that.

Fixes: cb67b832 ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The vport admin original link state will be re-applied after returning
back to legacy mode, it is not right to change the admin link state value
when in switchdev mode.

Use direct vport commands to alter logical vport state in netdev
representor open/close flows rather than the administrative eswitch API.

Fixes: 20a1ea67 ('net/mlx5e: Support VF vport link state control for SRIOV switchdev mode')
Signed-off-by: NJianbo Liu <jianbol@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

It's required to create a modules.alias via MODULE_DEVICE_TABLE helper
for the OF platform driver. Otherwise, module autoloading cannot work.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MODULE_ALIAS exports information to allow the module to be auto-loaded at
boot for the drivers registered using legacy platform registration.

However, currently the driver is always used by DT-only platform,
MODULE_ALIAS is redundant and should be removed properly.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We try to hold TX virtqueue mutex in vhost_net_rx_peek_head_len()
after RX virtqueue mutex is held in handle_rx(). This requires an
appropriate lock nesting notation to calm down deadlock detector.

Fixes: 03088137 ("vhost_net: basic polling support")
Reported-by: syzbot+7f073540b1384a614e09@syzkaller.appspotmail.com
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to support the modem found in HP EliteBook 820 G3.
Signed-off-by: NTorsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same fix as in 'bonding: move dev_mc_sync after master_upper_dev_link
in bond_enslave' is needed for team driver.

The panic can be reproduced easily:

  ip link add team1 type team
  ip link set team1 up
  ip link add link team1 vlan1 type vlan id 80
  ip link set vlan1 master team1

Fixes: cb41c997 ("team: team should sync the port's uc/mc addrs when add a port")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xin Long says:

====================
bonding: a bunch of fixes for dev hwaddr sync in bond_enslave

This patchset is mainly to fix a crash when adding vlan as slave of
bond which is also the parent link in patch 2/3,  and also fix some
err process problems in bond_enslave in patch 1/3 and 3/3.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When dev_set_promiscuity(1) succeeds but dev_set_allmulti(1) fails,
dev_set_promiscuity(-1) should be done before going to the err path.
Otherwise, dev->promiscuity will leak.

Fixes: 7e1a1ac1 ("bonding: Check return of dev_set_promiscuity/allmulti")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Beniamino found a crash when adding vlan as slave of bond which is also
the parent link:

  ip link add bond1 type bond
  ip link set bond1 up
  ip link add link bond1 vlan1 type vlan id 80
  ip link set vlan1 master bond1

The call trace is as below:

  [<ffffffffa850842a>] queued_spin_lock_slowpath+0xb/0xf
  [<ffffffffa8515680>] _raw_spin_lock+0x20/0x30
  [<ffffffffa83f6f07>] dev_mc_sync+0x37/0x80
  [<ffffffffc08687dc>] vlan_dev_set_rx_mode+0x1c/0x30 [8021q]
  [<ffffffffa83efd2a>] __dev_set_rx_mode+0x5a/0xa0
  [<ffffffffa83f7138>] dev_mc_sync_multiple+0x78/0x80
  [<ffffffffc084127c>] bond_enslave+0x67c/0x1190 [bonding]
  [<ffffffffa8401909>] do_setlink+0x9c9/0xe50
  [<ffffffffa8403bf2>] rtnl_newlink+0x522/0x880
  [<ffffffffa8403ff7>] rtnetlink_rcv_msg+0xa7/0x260
  [<ffffffffa8424ecb>] netlink_rcv_skb+0xab/0xc0
  [<ffffffffa83fe498>] rtnetlink_rcv+0x28/0x30
  [<ffffffffa8424850>] netlink_unicast+0x170/0x210
  [<ffffffffa8424bf8>] netlink_sendmsg+0x308/0x420
  [<ffffffffa83cc396>] sock_sendmsg+0xb6/0xf0

This is actually a dead lock caused by sync slave hwaddr from master when
the master is the slave's 'slave'. This dead loop check is actually done
by netdev_master_upper_dev_link. However, Commit 1f718f0f ("bonding:
populate neighbour's private on enslave") moved it after dev_mc_sync.

This patch is to fix it by moving dev_mc_sync after master_upper_dev_link,
so that this loop check would be earlier than dev_mc_sync. It also moves
if (mode == BOND_MODE_8023AD) into if (!bond_uses_primary) clause as an
improvement.

Note team driver also has this issue, I will fix it in another patch.

Fixes: 1f718f0f ("bonding: populate neighbour's private on enslave")
Reported-by: NBeniamino Galvani <bgalvani@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan_vids_add_by_dev is called right after dev hwaddr sync, so on
the err path it should unsync dev hwaddr. Otherwise, the slave
dev's hwaddr will never be unsync when this err happens.

Fixes: 1ff412ad ("bonding: change the bond's vlan syncing functions with the standard ones")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the qdisc lock was dropped in pfifo_fast we allow multiple
enqueue threads and dequeue threads to run in parallel. On the
enqueue side the skb bit ooo_okay is used to ensure all related
skbs are enqueued in-order. On the dequeue side though there is
no similar logic. What we observe is with fewer queues than CPUs
it is possible to re-order packets when two instances of
__qdisc_run() are running in parallel. Each thread will dequeue
a skb and then whichever thread calls the ndo op first will
be sent on the wire. This doesn't typically happen because
qdisc_run() is usually triggered by the same core that did the
enqueue. However, drivers will trigger __netif_schedule()
when queues are transitioning from stopped to awake using the
netif_tx_wake_* APIs. When this happens netif_schedule() calls
qdisc_run() on the same CPU that did the netif_tx_wake_* which
is usually done in the interrupt completion context. This CPU
is selected with the irq affinity which is unrelated to the
enqueue operations.

To resolve this we add a RUNNING bit to the qdisc to ensure
only a single dequeue per qdisc is running. Enqueue and dequeue
operations can still run in parallel and also on multi queue
NICs we can still have a dequeue in-flight per qdisc, which
is typically per CPU.

Fixes: c5ad119f ("net: sched: pfifo_fast use skb_array")
Reported-by: NJakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
The USB id is added to qmi_wwan.c to allow QMI communication with
the BM806U.

Tested on 4.14 kernel and OpenWRT.
Signed-off-by: NPawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

and switch to https where possible.

All links have been eyeballed to verify that the domains have
not changed, etc.
Signed-off-by: NSanjeev Gupta <ghane0@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.16

Some fixes for 4.16, only for iwlwifi and brcmfmac this time. All
pretty small.

iwlwifi

* fix an issue with the multicast queue

* fix IGTK handling

* fix some missing return value checks

* add support for a HW workaround for issues on some platforms

* a couple of fixes for channel-switch

* a few fixes for the aggregation handling code

brcmfmac

* drop Inter-Access Point Protocol packets by default

* fix check for ISO3166 regulatory code
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>