Introduce XDP support for XDP_TX verdict and ndo_xdp_xmit function
pointer.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report xdp stats through ethtool
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce basic XDP support to mtk_eth_soc driver.
Supported XDP verdicts:
- XDP_PASS
- XDP_DROP
- XDP_REDIRECT
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rely on page_pool allocator for single page buffers in order to keep
them dma mapped and add skb recycling support.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When rx_flag == MTK_RX_FLAGS_HWLRO,
rx_data_len = MTK_MAX_LRO_RX_LENGTH(4096 * 3) > PAGE_SIZE.
netdev_alloc_frag is for alloction of page fragment only.
Reference to other drivers and Documentation/vm/page_frags.rst

Branch to use __get_free_pages when ring->frag_size > PAGE_SIZE.
Signed-off-by: NChen Lin <chen45464546@163.com>
Link: https://lore.kernel.org/r/1654692413-2598-1-git-send-email-chen45464546@163.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Enable rx checksum offload for mt7986 chipset.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c8699805c18f7fd38315fcb8da2787676d83a32c.1654544585.git.lorenzo@kernel.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The "fsp->location" variable comes from user via ethtool_get_rxnfc().
Check that it is valid to prevent an out of bounds read.

Fixes: 7aab747e ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for mt7986-eth driver available on mt7986 soc.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the code converting scratch_ring pointer to void
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the code converting {tx,rx} ring dma pointer to void
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce MTK_NETSYS_V2 support. MTK_NETSYS_V2 defines 32B TX/RX DMA
descriptors.
This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce reg_map structure to add the capability to support different
register definitions. Move register definitions in mtk_regmap structure.
This is a preliminary patch to introduce mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove mtk_rx_dma structure layout dependency in mtk_rx_alloc/mtk_rx_clean.
Initialize to 0 rxd3 and rxd4 in mtk_rx_alloc.
This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a preliminary to ad mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to tx counterpart, introduce rxd_size in mtk_soc_data data
structure.
This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to remove mtk_tx_dma size dependency, introduce txd_size in
mtk_soc_data data structure. Rely on txd_size in mtk_init_fq_dma() and
mtk_dma_free() routines.
This is a preliminary patch to add mt7986 ethernet support.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move tx dma descriptor configuration in mtk_tx_set_dma_desc routine.
This is a preliminary patch to introduce mt7986 ethernet support since
it relies on a different tx dma descriptor layout.
Tested-by: NSam Shih <sam.shih@mediatek.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rely on GFP_KERNEL for dma descriptors mappings in mtk_tx_alloc(),
mtk_rx_alloc() and mtk_init_fq_dma() since they are run in non-irq
context.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Partially convert mtk_eth_soc to phylink_pcs, moving the configuration,
link up and AN restart over. However, it seems mac_pcs_get_state()
doesn't actually get the state from the PCS, so we can't convert that
over without a better understanding of the hardware.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The SGMIISYS configuration is performed while ETHSYS_SYSCFG0 is in a
disabled state. In order to preserve this when we switch to phylink_pcs
we need to move the restoration of this register to the mac_finish()
callback.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Move the setting of the MTK_MAC_MCR register from the end of mac_config
into the phylink mac_finish() method, to keep it as the very last write
that is done during configuration.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add a fixme comment for the last remaining incorrect usage of
state->speed in the mac_config() method, which is strangely in a code
path which is only run when the PHY interface mode changes.

This means if we are in RGMII mode, changes in state->speed will not
cause the INTF_MODE, TRGMII_RCK_CTRL and TRGMII_TCK_CTRL registers to
be set according to the speed, nor will the TRGPLL clock be set to the
correct value.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Provide mtk_sgmii_config() to wrap up the decisions about which SGMII
configuration will be called.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Now that mtk_sgmii_setup_mode_force() only uses the interface mode
from the phylink state, pass just the interface mode into this
function.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Phylink does not guarantee that state->duplex will be set correctly in
the mac_config() call, so it's a bug that the driver makes use of it.

Move the 802.3z PCS duplex configuration to mac_link_up().
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

mac->mode is only ever written to in one location, and is thus
superflous. Remove it.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rely on standard cci-control-port property to identify CCI port
reference.
Update mt7622 dts binding.
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware was designed to handle flow detection and creation of flow entries
by itself, relying on the software primarily for filling in egress routing
information.
When there is a hash collision between multiple flows, this allows the hardware
to maintain the entry for the most active flow.
Additionally, the hardware only keeps offloading active for entries with at
least 30 packets per second.

With this rework, the code no longer creates a hardware entries directly.
Instead, the hardware entry is only created when the PPE reports a matching
unbound flow with the minimum target rate.
In order to reduce CPU overhead, looking for flows belonging to a hash entry
is rate limited to once every 100ms.

This rework is also used as preparation for emulating bridge offload by
managing L4 offload entries on demand.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Preparation for adding more data to it, which will increase its size.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Wireless Ethernet Dispatch subsystem on the MT7622 SoC can be
configured to intercept and handle access to the DMA queues and
PCIe interrupts for a MT7615/MT7915 wireless card.
It can manage the internal WDMA (Wireless DMA) controller, which allows
ethernet packets to be passed from the packet switch engine (PSE) to the
wireless card, bypassing the CPU entirely.
This can be used to implement hardware flow offloading from ethernet to
WLAN.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It improves performance by eliminating the need for a cache flush on rx and tx
In preparation for supporting WED (Wireless Ethernet Dispatch), also add a
function for disabling coherent DMA at runtime.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang static analysis reports this problem
mtk_eth_soc.c:394:7: warning: Branch condition evaluates
  to a garbage value
                if (err)
                    ^~~

err is not initialized and only conditionally set.
So intitialize err.

Fixes: 7e538372 ("net: ethernet: mediatek: Re-add support SGMII")
Signed-off-by: NTom Rix <trix@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement read and write access to IEEE 802.3 Clause 45 Ethernet
phy registers while making use of new mdiobus_c45_regad and
mdiobus_c45_devad helpers.

Tested on the Ubiquiti UniFi 6 LR access point featuring
MediaTek MT7622BV WiSoC with Aquantia AQR112C.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of returning -1 (-EPERM) when MDIO bus is stuck busy
while writing or 0xffff if it happens while reading, return the
appropriate -ETIMEDOUT. Also fix return type to int instead of u32.
Refactor functions to use bitfield helpers instead of having various
masking and shifting constants in the code, which also results in the
register definitions in the header file being more obviously related
to what is stated in the MediaTek's Reference Manual.

Fixes: 656e7052 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is already an "int err" declared at the start of the function so
re-use that instead of declaring a shadow err variable.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211217070735.GC26548@kiliSigned-off-by: NJakub Kicinski <kuba@kernel.org>

mtk_eth_soc has not been updated for commit 7cceb599 ("net: phylink:
avoid mac_config calls"), and makes use of state->speed and
state->duplex in contravention of the phylink documentation. This makes
reliant on the legacy behaviours, so mark it as a legacy driver.
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>