Since mailbox message for installing flows is in place,
remove the RXVLAN_ALLOC mbox message which is redundant.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch handles the VF mac address changes as given below.
    1. mac addr configrued by VF will be retained until VF module unload.
    2. mac addr configred by PF for VF will be retained until power cycle.
    3. mac addr confgired by PF for its VF can't be overwritten by VF.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch adds support for ndo_set_vf_mac, ndo_set_vf_vlan
and ndo_get_vf_config handlers. The traffic redirection
based on the VF mac address or vlan id is done by installing
MCAM rules. Reserved RX_VTAG_TYPE7 in each NIXLF for VF VLAN
which strips the VLAN tag from ingress VLAN traffic. The NIX PF
allocates two MCAM entries for VF VLAN feature, one used for
ingress VTAG strip and another entry for egress VTAG insertion.

This patch also updates the MAC address in PF installed VF VLAN
rule upon receiving nix_lf_start_rx mbox request for VF since
Administrative Function driver will assign a valid MAC addr
in nix_lf_start_rx function.
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Co-developed-by: NTomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: NTomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch implements egress VLAN offload by appending NIX_SEND_EXT_S
header to NIX_SEND_HDR_S. The VLAN TCI information is specified
in the NIX_SEND_EXT_S. The VLAN offload in the ingress path is
implemented by configuring the NIX_RX_VTAG_ACTION_S to strip and
capture the outer vlan fields. The NIX PF allocates one MCAM entry
for Rx VLAN offload.
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch modifies the existing nix_vtag_config mailbox message
to allocate and free TX VTAG entries as requested by a NIX PF.
The TX VTAG entries are global resource that shared by all PFs
and each entry specifies the size of VTAG to insert and the VTAG
header data to insert. The mailbox response contains the entry
index which is used by mailbox requester in configuring the
NPC_TX_VTAG_ACTION for any MCAM entry.
Signed-off-by: NVamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Added new mailbox messages to install and delete MCAM rules.
These mailbox messages will be used for adding/deleting ethtool
n-tuple filters by NIX PF. The installed MCAM rules are stored
in a list that will be traversed later to delete the MCAM entries
when the interface is brought down or when PCIe FLR is received.
The delete mailbox supports deleting a single MCAM entry or range
of entries or all the MCAM entries owned by the pcifunc. Each MCAM
entry can be associated with a HW match stat entry if the mailbox
requester wants to check the hit count for debugging.

Modified adding default unicast DMAC match rule using install
flow API. The default unicast DMAC match entry installed by
Administrative Function is saved and can be changed later by the
mailbox user to fit additional fields, or the default MCAM entry
rule action can be used for other flow rules installed later.

Modified rvu_mbox_handler_nix_lf_free mailbox to add a flag to
disable or delete the MCAM entries. The MCAM entries are disabled
when the interface is brought down and deleted in FLR handler.
The disabled MCAM entries will be re-enabled when the interface
is brought up again.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The current default Key Extraction(KEX) profile can only use RX
packet fields while generating the MCAM search key. The profile
can't be used for matching TX packet fields. This patch modifies
the default KEX profile to add support for extracting TX packet
fields into MCAM search key. Enabled Tx KPU packet parsing by
configuring TX PKIND in tx_parse_cfg.

Modified the KEX profile to extract 2 bytes of VLAN TCI from an
offset of 2 bytes from LB_PTR. The LB_PTR points to the byte offset
where the VLAN header starts. The NPC KPU parser profile has been
modified to point LB_PTR to the starting byte offset of VLAN header
which points to the tpid field.
Signed-off-by: NStanislaw Kardach <skardach@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NNaveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch puts together all mailbox changes
for 98xx silicon:

Attach ->
Modify resource attach mailbox handler to
request LFs from a block address out of multiple
blocks of same type. If a PF/VF need LFs from two
blocks of same type then attach mbox should be
called twice.

Example:
        struct rsrc_attach *attach;
        .. Allocate memory for message ..
        attach->cptlfs = 3; /* 3 LFs from CPT0 */
        .. Send message ..
        .. Allocate memory for message ..
        attach->modify = 1;
        attach->cpt_blkaddr = BLKADDR_CPT1;
        attach->cptlfs = 2; /* 2 LFs from CPT1 */
        .. Send message ..

Detach ->
Update detach mailbox and its handler to detach
resources from CPT1 and NIX1 blocks.

MSIX ->
Updated the MSIX mailbox and its handler to return
MSIX offsets for the new block CPT1.

Free resources ->
Update free_rsrc mailbox and its handler to return
the free resources count of new blocks NIX1 and CPT1

Links ->
Number of CGX,LBK and SDP links may vary between
platforms. For example, in 98xx number of CGX and LBK
links are more than 96xx. Hence the info about number
of links present in hardware is useful for consumers to
request link configuration properly. This patch sends
this info in nix_lf_alloc_rsp.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NRakesh Babu <rsaladi2@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Initialize MCE context for the assigned NIX0/1
block for a CGX mapped PF. Modified rvu_nix_aq_enq_inst
function to work with nix_hw so that MCE contexts
for both NIX blocks can be inited.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NRakesh Babu <rsaladi2@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Firmware configures NIX block mapping for all CGXs
to achieve maximum throughput. This patch reads
the configuration and create mapping between RVU
PF and NIX blocks. And for LBK VFs assign NIX0 for
even numbered VFs and NIX1 for odd numbered VFs.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NRakesh Babu <rsaladi2@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch modifies NIX functions to operate
with nix_hw context so that existing functions
can be used for both NIX0 and NIX1 blocks. And
the NIX blocks present in the system are initialized
during driver init and freed during exit.
Signed-off-by: NRakesh Babu <rsaladi2@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Packet replication feature present in Octeontx2
is a hardware linked list of PF and its VF
interfaces so that broadcast packets are sent
to all interfaces present in the list. It is
driver job to add and delete a PF/VF interface
to/from the list when the interface is brought
up and down. This patch fixes the
npc_enadis_default_entries function to handle
broadcast replication properly if packet replication
feature is present.

Fixes: 40df309e ("octeontx2-af: Support to enable/disable default MCAM entries")
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor KPU related NPC code gathering all configuration data in a
structured format and putting it in one place (npc_profile.h).
This increases readability and makes it easier to extend the profile
configuration (as opposed to jumping between multiple header and source
files).

To do this:
* Gather all KPU profile related data into a single adapter struct.
* Convert the built-in MKEX definition to a structured one to streamline
  the MKEX loading.
* Convert LT default register configuration into a structure, keeping
  default protocol settings in same file where identifiers for those
  protocols are defined.
* Add a single point for KPU profile loading, so that its source may
  change in the future once proper interfaces for loading such config
  are in place.
Signed-off-by: NStanislaw Kardach <skardach@marvell.com>
Acked-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for PF/VF drivers to choose RSS flow key algorithm
with VLAN tag included in hashing input data. Only CTAG is considered.
Signed-off-by: NGeorge Cherian <george.cherian@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Four new mbox messages ids and handler are added in order to
enable or disable timestamping procedure on tx and rx side.
Additionally when PTP is enabled, the packet parser must skip
over 8 bytes and start analyzing packet data there. To make NPC
profiles work seemlesly PTR_ADVANCE of IKPU is set so that
parsing can be done as before when all data pointers
are shifted by 8 bytes automatically.
Co-developed-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NZyta Szpak <zyta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CGX LMAC, the physical interface can generate pause frames when
internal resources asserts backpressure due to exhaustion.

This patch configures CGX to generate 802.3 pause frames.
Also enabled processing of received pause frames on the line which
will assert backpressure on the internal transmit path.

Also added mailbox handlers for PF drivers to enable or disable
pause frames anytime.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each of the interface receive channels can be backpressured by
resources upon exhaustion or reaching configured threshold levels.
Resources here are receive buffer queues (Auras) and pkt notification
descriptor queues (CQs). Resources and interface channels are mapped
using backpressure IDs (BPIDs).

HW supports upto 512 BPIDs, this patch divides these BPIDs statically
across CGX/LBK/SDP interfaces as follows.
BPIDs 0 - 191 are mapped to LMAC channels, 16 per LMAC.
BPIDs 192 - 255 are mapped to LBK channels.
BPIDs 256 - 511 are mapped to SDP channels.
Also did the needed basic configuration of BPIDs.

Added mbox handlers with which a PF device can request for a BPID which
it will use to configure Auras and CQs.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanedup repititive nixlf and blkaddr retrieving logic
is various mailbox handlers throughout the rvu_nix.c file.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addes support to change interface MTU, MAC address
retrieval and config, RX mode ie unicast, multicast and promiscuous.
Also added link loopback support
Signed-off-by: NTomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Traffic for a CGX mapped NIXLF can be stopped by disabling entries
in NPC MCAM or by configuring CGX and mailbox messages exist for the
two options. If traffic is stopped at CGX then VFs of that PF are
also effected hence CGX traffic should be started/stopped by
tracking all the users of it. This patch implements that CGX users
tracking. CGX is also configured along with NPC if required.

Also removed a check which mandates even number of LBK VFs.
Signed-off-by: NSubbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A config option is added to disable caching of dynamic entries
like SQEs and stack pages. Also locks down all HW contexts in NDC,
preventing them from being evicted.

This option is useful when the queue count is large and there are
huge NDC cache misses. It's trade off between SQ context misses and
dynamically changing entries like SQE and stack page pointers.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each of the NIX/NPA LFs can choose which ways of their respective
NDC caches should be used to cache their contexts. This enables
flexible configurations like disabling caching for a LF, limiting
it's context to a certain set of ways etc etc. Separate way_mask
for NIX-TX and NIX-RX is not supported.
Signed-off-by: NGeetha sowjanya <gakula@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ingress packet replication support has been added to 96xx B0
silicon. This patch enables using that feature to replicate
ingress broadcast packets to PF and it's VFs.

Also fixed below issues
- VFs can also install NPC MCAM entry to forward broadcast pkts.
  Otherwise, unless PF's interface is UP, VFs will not receive
  bcast packets.
- NPC MCAM entry is disabled when PF and all it's VFs are down.
- Few corner cases in installing multicast entry list.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CN96xx initial silicon doesn't support all features pertaining to
NIX transmit scheduling and shaping.
- It supports a fixed topology of 1:1 mapped transmit
  limiters at all levels.
- Supports DWRR only at SMQ/MDQ and TL1.
- Doesn't support shaping and coloring.

This patch adds HW capability structure by which each variant
and skew of silicon can be differentiated by their supported
features. And adds support for A0 silicon's transmit scheduler
capabilities or rather limitations.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for few more RSS key types for flow key
algorithm to compute rss hash index.

Following flow key types have been added.
- Tunnel types like NVGRE, VXLAN, GENEVE.
- L2 offload type ETH_DMAC, Here we will consider only DMAC 6 bytes.
- And extension header IPV6_EXT (1 byte followed by IPV6 header
- Hashing inner protocol fields for inner DMAC, IPv4/v6, TCP, UDP, SCTP.
Signed-off-by: NKiran Kumar K <kirankumark@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updated NPC KPU packet parsing profile with support for following

- Fragmentation support for IPv4 IPv6 outer header
- NIX instruction header support
- QinQ with TPID of 0x8100 as non inner most vlan tag, as legacy
  network equipments still generate QinQ packets with this configuration.
- To better support RSS for tunnelled packets, udp based tunnel
  protocols such as vxlan, vxlan-gpe, geneve and gtpu are now
  captured into a separate layer E. Consequently, the inner
  packet headers are pushed one layer down to LF, LG, and LH
  accordingly.
- Support for rfc7510 mpls in udp. Up to 4 MPLS labels can be parsed
  and captured in one layer LE.
- Parser support for DSA, extended DSA and eDSA tags right after
  ethernet header by Marvell SOHO and Falcon switches. For extended
  DSA and eDSA tags, a special PKIND of 62 is used, as these tags don't
  contain a tpid field.
- Higig2 protocol header parsing support, added a NPC_LT_LA_HIGIG2_ETHER
  for a combined header of HIGIG2 and Ethernet.  Add a
  NPC_LT_LA_IH_NIX_HIGIG2_ETHER for a combined header of nix_ih,
  HIGIG2 and Ethernet on egress side. Also added 2 upper flags in LA to
  indicate the presence of nix_ih and HIGIG2.

Other changes include
- IPv4.TTL==0 IPv6.HLIM==0 check
- Per RFC 1858, mark fragment offset == 1 as error
- TCP invalid flags check
- Separate error codes for outer and inner IPv4 checksum errors.
- Fix a parser error when KPU parses incoming IPSec ESP and AH packets
- NPC vtag capture/strip hardware expect tag pointer to point to
  tpid/ethertype instead of tci. So move lb_ptr to point to tpid/ethertype.
- Fix npc parser error when parsing udp packets that don't have any payload.
- For a single MCAM entry to match on packets with one or stacked vlan tags
  combine NPC_LT_LB_STAG and NPC_LT_LB_QINQ to NPC_LT_LB_STAG_QINQ.
- NVGRE to have a separate ltype LD_NVGRE instead of combined with LD_GRE.
- Reserve top LD/LTYPEs to support custom KPU profile fields.
Signed-off-by: NHao Zheng <haoz@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIX_AF_LSO_FORMAT(0..31)_FIELD(0..7) register enables an SW defined
means to define LSO packet modification formats.

0..31 works as an index to choose the algorithm, On success, the mailbox
returns the index to the client of chosen LSO algorithm selection.
This index will be used in configuring the transmit descriptors.

Add mailbox interface to dynamically reserve and configure LSO format.

This commit also fixes 'sizem1' for NIX_LSOALG_TCP_FLAGS
to '1' i.e 2 Bytes.
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds mailbox support for L4 checksum verification
and L3 and L4 length verification configuration.
Signed-off-by: NVidhya Raman <vraman@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setup TPID's for vlan0 and vlan1 for Tx VLAN insertion offloads.
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIX_AF_MARK_FORMAT(0..127)_CTL register enables an SW defined
means to mark/insert various data in the packet based on
final packet color from traffic shaping HW.

0..127 works as an index to choose the algorithm. On success,
the mailbox returns the index to the client.

Add NIX_MARK_FORMAT_CFG mailbox which reserves mark format based on
tuple (offset, y_mask, y_val, r_mask, r_val)

If the tuple is requested again for mark format that was already
reserved, then it will be reused. If not it will reserve a new entry
if space is available.

Also on AF init commonly used marker format such as VLAN DEI, IPv4
ECN, IPv4 DSCP are reserved for AF consumers.
Signed-off-by: NKrzysztof Kanas <kkanas@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support all NIX specific valid length errors and
checksum errors on Rx, Update all NIX_AF_RX_DEF_* registers.

Also sorted all registers in HRM definition order.
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default behavior was to free all the TLx Tx schedule
queues. This patch adds support for freeing a single Tx
schedule queue if TXSCHQ_FREE_ALL flag is not set.
Signed-off-by: NKrzysztof Kanas <kkanas@marvell.com>
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TL1 is the root node in the scheduling hierarchy and
it is a global resource with a limited number.

This patch introduces restriction and validation on
the allocation of the TL1 nodes for the effective resource
sharing across the AF consumers.

- Limit TL1 allocation to 2 per lmac.
  One could be for the normal link and one for IEEE802.3br
  express link (Express Send DMA).
  Effectively all the VF's of an RVU PF(lmac) share the two TL1 schqs.
- TL1 cannot be freed once allocated.
- Allow VF's to only apply default config to TL1 if not
  already applied. PF's can always overwrite the TL1 config.
- Consider NIX_AQ_INSTOP_WRITE while validating txschq
  when sq.ena is set.
Signed-off-by: NKrzysztof Kanas <kkanas@marvell.com>
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduced reserve_flowkey_alg_idx()to reserve RSS algorithm index,
it would internally use set_flowkey_fields() to generate fields
based on the flow key dynamically.

On AF driver init, it would reserve a predefined set RSS algo indexes,
which will be available all the time for all the AF driver consumers.
The leftover algo indexes can be reserved at runtime through
exiting nix_rss_flowkey_cfg mailbox message.

The NIX_FLOW_KEY_TYPE_PORT is removed from predefined a set of RSS flow
type as it is not used by any consumer.
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce state-based algorithm to convert the flow_key value
to RSS algo field used by NIX_AF_RX_FLOW_KEY_ALGX_FIELDX register.

The outer `for loop` goes over _all_ protocol field and the following
variables depict the state machine forward progress logic.

a) keyoff_marker - Enabled when hash byte length needs to be accounted
in field->key_offset update.
b) field_marker - Enabled when a new field needs to be selected.
c) group_member - Enabled when a protocol is part of a group.

This would remove the existing hard coding and enable to add
new protocol support seamlessly.
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NNithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added response for nix_rss_flowkey_cfg message to return
selected RSS algorithm index.

The FLOW_KEY_TYPE* definition is part of the mbox message and
it will be used by the other consumers of AF driver hence moving to mbox.h.

Also renamed FLOW_* definitions to NIX_FLOW_* to avoid global
name space collisions, as we have various coming from
include/uapi/linux/pkt_cls.h for example.
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the time of initial broadcast packet replication table init,
NIXLFs are not yet attached to PF_FUNCs. Hence skipped checking
NIXLF while submitting MCE entry init instruction to NIX admin queue.

Also did a minor cleanup while installing bcast match entry in
packet parser unit i.e NPC.
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NJerin Jacob <jerinj@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For this, cgx_id(struct cgx) definition has been changed to
reflect cgx port id instead of device instance id.
Now cgx_id can be directly used as channel offset for NPC configuration.
Assumptions on contiguous cgx port ids has been removed from
nix_calibrate_x2p as well.

As a side effect, allocation of conversion tables that were based
on cgx count are changed to cgx port id max value.
Tables would return NULL for invalid cgx ports.
Signed-off-by: NLinu Cherian <lcherian@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>