Signed-off-by: NAndrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit f397d7c4.

This series isn't quite ready for 3.5 just yet, so revert it and give
the author more time to get it correct.

Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit bebc56d5.

The call here is fragile and not well thought out, so revert it, it's
not fully baked yet and I don't want this to go into 3.5.

Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Basically, ->vbus_session() calls should be served when VBUS session
starts and ends (it's not whenever transciever drivers detect VBUS
_changes_).  Otherwise, if UDC gadget drivers don't want for some
reason ->vbus_session() calls with the same "is_active" value, either
OTG or UDC drivers need to have some protection handlings.

Also, on platforms using this 'gpio_vbus' driver, the driver is only
allowed to check whether VBUS is applied.  There is no kernel-standard
way prepared for UDC gadget drivers to do that.

With this in mind, gpio_vbus should try to prevent unnecessary
consecutive vbus_session calls being served with the same "in_active"
value.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Note that regulator_put() doesn't care about whether ->vbus_draw is
valid or not.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In commit c2344f13 (USB: gpio_vbus:
add delayed vbus_session calls, 2009-01-24), usb_gadget_vbus_connect()
and ...disconnect() were extracted from the interrupt handler, so to
allow vbus_session handlers to deal with msleep() calls.

This patch takes the approach one step further.

USB2.0 specification (7.1.7.3 Connect and Disconnect Signaling) says
that the USB system software (shall) provide a debounce interval with
a minimum duration of 100 ms, which ensures that the electrical and
mechanical connection is stable before software attempts to reset
the attached device.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

'dev_id' has to be the same with the one passed to request_irq().
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If no default value is specified, then 'n' is used so the default value
used here is not needed. Furthermore, we should never change default
values depending on EXPERT mode. EXPERT mode should only make options
visible, not change them.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently usb_put_transceiver calls put_device so this is a no-op but it
is better to keep API usage consistent as ohci->transceiver is allocated
with usb_get_transceiver.

While at there remove one extra ohci->transceiver test as the code block
has already tested it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently usb_put_transceiver calls put_device so this is a no-op but it
is better to keep API usage consistent as ehci->transceiver is allocated
with usb_get_transceiver.

While at there remove one extra ehci->transceiver test as the code block
has already tested it.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move child's pointer to the struct usb_hub_port since the child device
is directly associated with the port. Provide usb_get_hub_child_device()
to get child's pointer.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add struct usb_hub_port pointer port_data in the struct usb_hub and allocate
struct usb_hub_port perspectively for each ports to store private data.
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI offers two methods that allow us to infer whether or not a USB port
is removable. The _PLD method gives us information on whether the port is
"user visible" or not. If that's not present then we can fall back to the
_UPC method which tells us whether or not a port is connectable.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Built-in USB devices will typically have a representation in the system
ACPI tables. Add support for binding the two together so the USB code can
make use of the associated methods.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a simple helper function to allow drivers to obtain the physical
device location data.
Acked-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It's unreasonable to have CONFIG_ACPI for these in drivers, so add some
stub functions.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that the ChipIdea driver and related platform code has its own
location in the kernel and more contributions from the interested
parties are anticipated, add a new maintainer for it.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have the chipidea driver now that supports both langwell and penwell,
so there is no need for this one any more.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It was used as a shorthand for gadget's device in request mapping/unmapping
code, but now it's not used any more.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We're one of the remaining drivers to map/unmap requests by hand. Switch
to using generic gadget routines for that instead.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some implementations need this limitation to work correctly.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds EHCI host support to the chipidea driver. We want it to be
part of the hdrc driver and not a standalone (sub-)driver module, as
the structure of ehci-hcd.c suggests, so for chipidea controller we
hack it to not provide platform-related code, but only the ehci hcd.

The ehci-platform driver won't work for us here too, because the
controller uses the same registers for both device and host mode and
also otg-related bits, so it's not really possible to put ehci registers
into a separate resource.

This is not a pretty solution, but the alternative is exporting symbols
from the chipidea driver to a ehci-chipidea driver and doing all the
module refcounting.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of the bits of USBMODE register are defined in <usb/ehci_def.h>,
use them instead of having our own definitions.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These definitions are unused, and the same registers are also defined
in <linux/usb/msm_hsusb_hw.h>.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, gadget can't be NULL in _gadget_stop_activity().
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move spin_lock under the done label, so the
lock will also be pulled in the error paths.
Signed-off-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
[rebased on top of the patchset]
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Get rid of trailing comments in the structure definitions in favor of
kernel-doc.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The old implementation used global hw_bank, the new implementation uses
udc-local hw_bank. This field seems to be a leftover from previous coding
experiments.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add some generic code for roles and implement simple role switching
based on ID pin state and/or a sysfs file. At this, we also rename
the device to ci_hdrc, which is what it is.

The "manual" switch is made into a sysfs file and not debugfs, because
it might be useful even in non-debug context. For some boards, like
sheevaplug, it seems to be the only way to switch roles without modifying
the hardware, since the ID pin is always grounded.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Split the driver into the following parts:
  * core  -- resources, register access, capabilities, etc;
  * udc   -- device controller functionality;
  * debug -- logging events.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since chipidea is a dual role controller, it makes sense to move it
to its own directory, where we can also have host, otg and platform
code related to this controller. It also makes sense to break out
the driver into several compilation units like udc, host, debugging
code, etc.

Firstly, let's move the udc and platform code to drivers/usb/chipidea.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Report basic information about capabilities and register addresses on
probe.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Newer versions of the chipidea controller support the "advance" setting
of usb address, which means instead of setting it immediately, deferring
it till the status completion. Unfortunately, older versions of the
controller don't have this feature, so in order to support those too, we
simply don't use it. It's about 4 lines of extra code, and isn't in any
way critical to performance. While at it, change the return value of the
hw_usb_set_address() to void, since it can't fail in any measurable way.

With this patch, ci13xxx_udc driver works with the chipidea controller in
kirkwood (feroceon SoC), as found in, for example, sheevaplug.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The regmap field is an array of register pointers, not the other way
around.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no point in having tracing output in the kernel these days.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't try to initialize devices that don't have driver_data assigned
to their pci ids.
Reported-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevents dereferencing an invalid struct usb_interface
pointer.

Always delete entry from device list whether or not the
rest of the device state cleanup is postponed. The device
list uses desc->intf as key, and wdm_open will dereference
this key while searching for a matching device.  A device
should not appear in the list unless probe() has succeeded
and disconnect() has not finished.

Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We cannot dereference a removed USB interface for
dev_printk. Use pr_debug instead where necessary.

Flush errors are expected if device is unplugged and are
therefore best ingored at this point.

Move the kill_urbs() call in wdm_release with dev_dbg()
for the non disconnect, as we know it has already been
called if WDM_DISCONNECTING is set.  This does not
actually fix anything, but keeps the code more consistent.

Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Else the poll will be restarted indefinitely in a tight loop,
preventing final device cleanup.

Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The warning shown up when ran with randconfig,

warning: (USB_DWC3) selects USB_XHCI_PLATFORM which has unmet direct dependencies (USB_SUPPORT && USB_XHCI_HCD)
Signed-off-by: Njoseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>