The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com

MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.

One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a

'Timed out waiting for ACT sent when disabling'

error, due to reading from the incorrect DP_TP_STATUS register.

This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.

v2:
- Correct the failure scenario in the commit log. (José)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com

For all ddi, encoder->type holds output type as ddi,
assigning it to individual o/p types is no more valid.

Fixes: 362bfb99 ("drm/i915/tgl: Add DKL PHY vswing table for HDMI")

v2: Rebase, no functional change.
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612082237.11886-1-vandita.kulkarni@intel.com

According to BSpec the Data Island Packet should be disabled after
disabling the transcoder, but before the transcoder clock select is set
to none. On an ICL RVP, daisy-chained MST config not following this
leads to a hang with the following MCE when disabling the output:

[  870.948739] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: ba00000011000402
[  871.019212] mce: [Hardware Error]: RIP !INEXACT! 10:<ffffffff81aca652> {poll_idle+0x92/0xb0}
[  871.019212] mce: [Hardware Error]: TSC 135a261fe61
[  871.019212] mce: [Hardware Error]: PROCESSOR 0:706e5 TIME 1591739604 SOCKET 0 APIC 0 microcode 20
[  871.019212] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[  871.019212] mce: [Hardware Error]: Machine check: Processor context corrupt
[  871.019212] Kernel panic - not syncing: Fatal machine check
[  871.019212] Kernel Offset: disabled

Bspec: 4287

Fixes: fa37a213 ("drm/i915: Stop sending DP SDPs on ddi disable")
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609220616.6015-1-imre.deak@intel.com

Setting ln0 similar to ln1

Fixes: 3b51be4e ("drm/i915/tc: Update DP_MODE programming")
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: NKhaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200608204537.28468-1-khaled.almahallawy@intel.com

As latest update we have now 2 voltage swing tables for DP over DKL
PHY with only one difference in Level 0 pre-emphasis 3.
So with 2 tables for DP is time to have one single function to return
all DKL voltage swing tables.

BSpec: 49292
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Tested-by: NKhaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602205424.138143-1-jose.souza@intel.com

Different platforms have different max vswing/preemph settings.
Turn that into a pair vfuncs so we can decouple intel_dp.c and
intel_ddi.c further.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-5-ville.syrjala@linux.intel.comReviewed-by: NManasi Navare <manasi.d.navare@intel.com>

Cometlake is a small refresh of Coffeelake, but since we have found out a
difference in the plaforms, we need to identify them as separate platforms.

Since we previously took Coffeelake/Cometlake as identical, update all
IS_COFFEELAKE() to also include IS_COMETLAKE().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602140541.5481-1-chris@chris-wilson.co.uk

Small updates in dkl_de_emphasis_control field.

BSpec: 49292
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NKhaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200529232757.37832-1-jose.souza@intel.com

In order to use a common VSC SDP Colorimetry calculating code on PSR,
it uses a new psr vsc sdp compute routine.
Because PSR routine has its own scenario and timings of writing a VSC SDP,
the current PSR routine needs to have its own drm_dp_vsc_sdp structure
member variable on struct i915_psr.

In order to calculate colorimetry information, intel_psr_update()
function and intel_psr_enable() function extend a drm_connector_state
argument.

There are no changes to PSR mechanism.

v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Rebased
v8: Rebased
v10: When a PSR is enabled, it needs to add DP_SDP_VSC to
     infoframes.enable.
     It is needed for comparing between HW and pipe_state of VSC_SDP.
v11: If PSR is disabled by flag, it don't enable psr on pipe compute.
v12: Fix an inconsistent indenting
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-15-gwan-gyeong.mun@intel.com

Call intel_dp_set_infoframes(false) function on intel_ddi_post_disable_dp()
to make sure not to send VSC SDP and HDR Metadata Infoframe SDP.

v5: Polish commit message [Uma]
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-13-gwan-gyeong.mun@intel.com

Call intel_dp_set_infoframes() function on pipe updates to make sure
that we send VSC SDP and HDR Metadata Infoframe SDP (when applicable)
on fastsets.
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-12-gwan-gyeong.mun@intel.com

Added state readout for DP VSC SDP and enabled state validation
for DP VSC SDP.

v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: Skip checking of VSC SDP when a crtc config has psr.
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-10-gwan-gyeong.mun@intel.com

Added state readout for DP HDR Metadata Infoframe SDP.

v9: Rebased
v10: Rebased
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-9-gwan-gyeong.mun@intel.com

In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.

Before:
 intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
 configs and program sdp registers on enable callback of encoder.

After:
 It separates computing of sdp configs and programming of sdp register.
 The compute config callback of encoder calls computing sdp configs.
 The enable callback of encoder calls programming sdp register.

v3: Rebased
v5: Polish commit message [Uma]
v10: Rebased
Signed-off-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com

Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.

v2: Duplicate stuff to avoid exposing platform specific
    functions across files (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.

v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
    functions across files (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Split some overly long lines.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420200610.31798-4-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Relocate a bunch of DDI specific code from intel_dp.c to intel_ddi.c
by introducing a .set_idle_link_train() vfunc.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420200610.31798-3-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Sort out some of the mess between intel_ddi.c intel_dp.c by
introducing a .set_signal_levels() vfunc.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420200610.31798-2-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Sort out some of the mess between intel_ddi.c intel_dp.c by
introducing a .set_link_train() vfunc.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420200610.31798-1-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.

Prefer drm_WARN* over WARN* calls.
Signed-off-by: NPankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406112800.23762-4-pankaj.laxminarayan.bharadiya@intel.com

Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com

Pass the encoder all the way down to
intel_ddi_transcoder_func_reg_val_get(). Allows us eliminate the
intel_ddi_get_crtc_encoder() eyesore.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-4-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJani Nikula <jani.nikula@intel.com>

Push the TRANS_DDI_FUNC_CTL into the encoder enable hook. The disable
is already there, and as a followup will enable us to pass the encoder
all the way down.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-3-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJani Nikula <jani.nikula@intel.com>

Since intel_ddi_enable_pipe_clock() was pushed down into the
encoder hooks we can pass on the encoder instead of having
to use intel_ddi_get_crtc_encoder().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NJani Nikula <jani.nikula@intel.com>

Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.

So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.

In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.

So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.

Fixes: 4444df6e ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com

DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.

ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.

So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.

v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI

Fixes: bd3cf6f7 ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
(cherry picked from commit 70988115)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.

This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)

and avoids leaking the power ref when disabling the output.

Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
(cherry picked from commit f77a2db2)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

On TypeC ports if a sink deasserts/reasserts its HPD signal, generating
a hotplug interrupt without the sink getting unplugged/replugged from
the connector, there can be an up to 3 seconds delay until the AUX
channel gets functional. To avoid detection failures this delay causes
retry the detection for 5 seconds.

I noticed this on ICL/TGL RVPs and a DELL XPS 13 7390 ICL laptop.

References: https://gitlab.freedesktop.org/drm/intel/issues/1067Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-2-imre.deak@intel.com

On TypeC connectors we need to retry the detection after hotplug events
for a longer time, so add a retry counter to support this. The next
patch will add detection retries on TypeC ports needing this.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-1-imre.deak@intel.com

Move the final DP_TP_CTL frobbing of port sync to the master
encoder's enable hook. Now neatly out of sight from the high level
modeset code.

And thus we've eliminated all the special casing of port sync
in the high level modeset code.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-14-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.

The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.

Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Transcoder port sync was introduced to the hardware in BDW. We
can trivially enable it for SKL+ since the same codepaths are
already used for ICL+ port sync. The only difference is the actual
location of the bits we need to poke.

We leave BDW out (at least for now) since it uses different modeset
paths that haven't been adapted for port sync, and IIRC using the
feature would involve some extra workarounds we've not implemented.

Pre-BDW hardware does not support port sync so we'd have to tweak
the modeset sequence to start the pipes as close together as possible
and hope for the best. So far no one has seriously tried to implement
that.

Closes: https://gitlab.freedesktop.org/drm/intel/issues/27Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-9-ville.syrjala@linux.intel.comReviewed-by: NManasi Navare <manasi.d.navare@intel.com>

We have a bunch of code that would like to know which
CPU transcoders are actually present in the hardware. Rather than
use various ad-hoc methods let's just include a full bitmask in
the device info, alongside pipe_mask.

v2: Rebase
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318170235.15176-1-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Specification was updated with vswing tables for different
configurations.
Also reordering icl_mg_phy_ddi_buf_trans struct to match table order.

BSpec: 21735
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NClinton Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-3-jose.souza@intel.com

EHL has now only one table for all DP rates.

BSpec: 21257
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-2-jose.souza@intel.com

DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.

ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.

So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.

v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI

Fixes: bd3cf6f7 ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com

The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.

This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)

and avoids leaking the power ref when disabling the output.

Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com

Clean up the TRANS_DDI_FUNC_CTL2 programming/readout by
using REG_FIELD_PREP() & co.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-6-ville.syrjala@linux.intel.comReviewed-by: NManasi Navare <manasi.d.navare@intel.com>