The GSWIP switch accesses various bridging layer tables (VLANs, FDBs,
forwarding rules) indirectly through PCE registers. These hardware
accesses are non-atomic, being comprised of several register reads and
writes.

These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().

So this driver needs to serialize the access to the PCE registers using
its own locking scheme. This patch adds that.

Note that the driver also uses the gswip_pce_load_microcode() function
to load a static configuration for the packet classification engine into
a table using the same registers. It is currently not protected, but
since that configuration is only done from the dsa_switch_ops :: setup
method, there is no risk of it being concurrent with other operations.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 965e6b26, reversing
changes made to 4d98bb0d.

This converts instances of
	bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS)
to
	linkmode_foo(args...)

I manually fixed up some lines to prevent them from being excessively
long. Otherwise, this change was generated with the following semantic
patch:

// Generated with
// echo linux/linkmode.h > includes
// git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \
// | sort | uniq | tee new_includes | wc -l && mv new_includes includes
// and repeating until the number stopped going up
@i@
@@

(
 #include <linux/acpi_mdio.h>
|
 #include <linux/brcmphy.h>
|
 #include <linux/dsa/loop.h>
|
 #include <linux/dsa/sja1105.h>
|
 #include <linux/ethtool.h>
|
 #include <linux/ethtool_netlink.h>
|
 #include <linux/fec.h>
|
 #include <linux/fs_enet_pd.h>
|
 #include <linux/fsl/enetc_mdio.h>
|
 #include <linux/fwnode_mdio.h>
|
 #include <linux/linkmode.h>
|
 #include <linux/lsm_audit.h>
|
 #include <linux/mdio-bitbang.h>
|
 #include <linux/mdio.h>
|
 #include <linux/mdio-mux.h>
|
 #include <linux/mii.h>
|
 #include <linux/mii_timestamper.h>
|
 #include <linux/mlx5/accel.h>
|
 #include <linux/mlx5/cq.h>
|
 #include <linux/mlx5/device.h>
|
 #include <linux/mlx5/driver.h>
|
 #include <linux/mlx5/eswitch.h>
|
 #include <linux/mlx5/fs.h>
|
 #include <linux/mlx5/port.h>
|
 #include <linux/mlx5/qp.h>
|
 #include <linux/mlx5/rsc_dump.h>
|
 #include <linux/mlx5/transobj.h>
|
 #include <linux/mlx5/vport.h>
|
 #include <linux/of_mdio.h>
|
 #include <linux/of_net.h>
|
 #include <linux/pcs-lynx.h>
|
 #include <linux/pcs/pcs-xpcs.h>
|
 #include <linux/phy.h>
|
 #include <linux/phy_led_triggers.h>
|
 #include <linux/phylink.h>
|
 #include <linux/platform_data/bcmgenet.h>
|
 #include <linux/platform_data/xilinx-ll-temac.h>
|
 #include <linux/pxa168_eth.h>
|
 #include <linux/qed/qed_eth_if.h>
|
 #include <linux/qed/qed_fcoe_if.h>
|
 #include <linux/qed/qed_if.h>
|
 #include <linux/qed/qed_iov_if.h>
|
 #include <linux/qed/qed_iscsi_if.h>
|
 #include <linux/qed/qed_ll2_if.h>
|
 #include <linux/qed/qed_nvmetcp_if.h>
|
 #include <linux/qed/qed_rdma_if.h>
|
 #include <linux/sfp.h>
|
 #include <linux/sh_eth.h>
|
 #include <linux/smsc911x.h>
|
 #include <linux/soc/nxp/lpc32xx-misc.h>
|
 #include <linux/stmmac.h>
|
 #include <linux/sunrpc/svc_rdma.h>
|
 #include <linux/sxgbe_platform.h>
|
 #include <net/cfg80211.h>
|
 #include <net/dsa.h>
|
 #include <net/mac80211.h>
|
 #include <net/selftests.h>
|
 #include <rdma/ib_addr.h>
|
 #include <rdma/ib_cache.h>
|
 #include <rdma/ib_cm.h>
|
 #include <rdma/ib_hdrs.h>
|
 #include <rdma/ib_mad.h>
|
 #include <rdma/ib_marshall.h>
|
 #include <rdma/ib_pack.h>
|
 #include <rdma/ib_pma.h>
|
 #include <rdma/ib_sa.h>
|
 #include <rdma/ib_smi.h>
|
 #include <rdma/ib_umem.h>
|
 #include <rdma/ib_umem_odp.h>
|
 #include <rdma/ib_verbs.h>
|
 #include <rdma/iw_cm.h>
|
 #include <rdma/mr_pool.h>
|
 #include <rdma/opa_addr.h>
|
 #include <rdma/opa_port_info.h>
|
 #include <rdma/opa_smi.h>
|
 #include <rdma/opa_vnic.h>
|
 #include <rdma/rdma_cm.h>
|
 #include <rdma/rdma_cm_ib.h>
|
 #include <rdma/rdmavt_cq.h>
|
 #include <rdma/rdma_vt.h>
|
 #include <rdma/rdmavt_qp.h>
|
 #include <rdma/rw.h>
|
 #include <rdma/tid_rdma_defs.h>
|
 #include <rdma/uverbs_ioctl.h>
|
 #include <rdma/uverbs_named_ioctl.h>
|
 #include <rdma/uverbs_std_types.h>
|
 #include <rdma/uverbs_types.h>
|
 #include <soc/mscc/ocelot.h>
|
 #include <soc/mscc/ocelot_ptp.h>
|
 #include <soc/mscc/ocelot_vcap.h>
|
 #include <trace/events/ib_mad.h>
|
 #include <trace/events/rdma_core.h>
|
 #include <trace/events/rdma.h>
|
 #include <trace/events/rpcrdma.h>
|
 #include <uapi/linux/ethtool.h>
|
 #include <uapi/linux/ethtool_netlink.h>
|
 #include <uapi/linux/mdio.h>
|
 #include <uapi/linux/mii.h>
)

@depends on i@
expression list args;
@@

(
- bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_zero(args)
|
- bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_copy(args)
|
- bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_and(args)
|
- bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_or(args)
|
- bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_empty(args)
|
- bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_andnot(args)
|
- bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_equal(args)
|
- bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_intersects(args)
|
- bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS)
+ linkmode_subset(args)
)

Add missing linux/mii.h include to mellanox. -DaveM
Signed-off-by: NSean Anderson <sean.anderson@seco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looking at the code, the GSWIP switch appears to hold bridging service
structures (VLANs, FDBs, forwarding rules) in PCE table entries.
Hardware access to the PCE table is non-atomic, and is comprised of
several register reads and writes.

These accesses are currently serialized by the rtnl_lock, but DSA is
changing its driver API and that lock will no longer be held when
calling ->port_fdb_add() and ->port_fdb_del().

So this driver needs to serialize the access to the PCE table using its
own locking scheme. This patch adds that.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: NAleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.

What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.

This message can be seen in a loop, and it hangs the reboot process there:

unregister_netdevice: waiting for eth0 to become free. Usage count = 3

So why 3?

A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:

dsa_slave_create
-> netdev_upper_dev_link
   -> __netdev_upper_dev_link
      -> __netdev_adjacent_dev_insert
         -> dev_hold

So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.

Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.

It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.

So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.

However, complications arise really quickly.

The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).

Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.

So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.

So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.

The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.

The answer to that question lies in this comment above device_link_add:

 * A side effect of the link creation is re-ordering of dpm_list and the
 * devices_kset list by moving the consumer device and all devices depending
 * on it to the ends of these lists (that does not happen to devices that have
 * not been registered when this function is called).

so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.

Fixes: 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The delay is especially needed by the xRX300 and xRX330 SoCs. Without
this patch, some phys are sometimes not properly detected.

The patch was tested on BT Home Hub 5A and D-Link DWR-966.

Fixes: a09d042b ("net: dsa: lantiq: allow to use all GPHYs on xRX300 and xRX330")
Signed-off-by: NAleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, outgoing packets larger than 1496 bytes are dropped when
tagged VLAN is used on a switch port.

Add the frame check sequence length to the value of the register
GSWIP_MAC_FLEN to fix this. This matches the lantiq_ppa vendor driver,
which uses a value consisting of 1518 bytes for the MAC frame, plus the
lengths of special tag and VLAN tags.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Signed-off-by: NJan Hoffmann <jan@3e8.eu>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).

When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.

Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.

Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.

Fixes: 58c59ef9 ("net: dsa: lantiq: Add Forwarding Database access")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.

For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.

The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).

Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.

While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
  PHY11G instances) are working fine but the two Fast Ethernet ports
  (using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
  received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
  as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
  makes the PHY auto polling state machine (rightfully?) think that the
  established link speed (when the other side is Gbit/s capable) is
  1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
  connected to the internal PHY11G GPHYs while the other three are
  external RGMII PHYs) are working. Neither RX nor TX traffic was
  observed. It is not clear which part of the PHY auto polling state-
  machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
  internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
  random disconnects (link down events could be seen). Sometimes all
  traffic would stop after such disconnect. It is not clear which part
  of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
  running in PHY11G / Gbit/s mode, the other two are external RGMII
  PHYs) was affected by similar issues as the FritzBox 7412 just without
  the "link down" events

Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)

After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.

Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.

As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb2 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.

This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Verify compatible string against hardware.
Signed-off-by: NAleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows to use all PHYs on GRX300 and GRX330. The ARX300
has 3 and the GRX330 has 4 integrated PHYs connected to different
ports compared to VRX200. Each integrated PHY can work as single
Gigabit Ethernet PHY (GMII) or as double Fast Ethernet PHY (MII).

Allowed port configurations:

xRX200:
GMAC0: RGMII, MII, REVMII or RMII port
GMAC1: RGMII, MII, REVMII or RMII port
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port

xRX300:
GMAC0: RGMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port

xRX330:
GMAC0: RGMII, GMII or RMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII) or GPHY3 (GMII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII), RGMII or RMII port

Tested on D-Link DWR966 (xRX330) with OpenWRT.
Signed-off-by: NAleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in commit 54a0ed0d ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.

New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.

Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.

The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.

The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.

Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.

No behavior change except for the added prints is intended at this time.

$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[   60.315148] br0: port 1(sw0p2) entered blocking state
[   60.320350] br0: port 1(sw0p2) entered disabled state
[   60.327839] device sw0p2 entered promiscuous mode
[   60.334905] br0: port 1(sw0p2) entered blocking state
[   60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NKurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.

So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.

It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.

Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8ece ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.

It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.

This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.

In part, this patch contains a revert of my previous commit 2e554a7a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").

For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
  implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
  done mechanically, by pasting the implementation twice, then only
  keeping the code that would get executed during prepare phase on top,
  then only keeping the code that gets executed during the commit phase
  on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
  multicast router could be converted right away. But the ageing time
  could not, so a shim was introduced and this was left for a further
  commit.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The call path of a switchdev VLAN addition to the bridge looks something
like this today:

        nbp_vlan_init
        |  __br_vlan_set_default_pvid
        |  |                       |
        |  |    br_afspec          |
        |  |        |              |
        |  |        v              |
        |  | br_process_vlan_info  |
        |  |        |              |
        |  |        v              |
        |  |   br_vlan_info        |
        |  |       / \            /
        |  |      /   \          /
        |  |     /     \        /
        |  |    /       \      /
        v  v   v         v    v
      nbp_vlan_add   br_vlan_add ------+
       |              ^      ^ |       |
       |             /       | |       |
       |            /       /  /       |
       \ br_vlan_get_master/  /        v
        \        ^        /  /  br_vlan_add_existing
         \       |       /  /          |
          \      |      /  /          /
           \     |     /  /          /
            \    |    /  /          /
             \   |   /  /          /
              v  |   | v          /
              __vlan_add         /
                 / |            /
                /  |           /
               v   |          /
   __vlan_vid_add  |         /
               \   |        /
                v  v        v
      br_switchdev_port_vlan_add

The ranges UAPI was introduced to the bridge in commit bdced7ef
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.

Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328b ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:

br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink

Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.

In the meantime, commits such as 0944d6b5 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.

Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and  __vlan_add
(the latter coming from commit 9c86ce2c ("net: bridge: Notify about
bridge VLANs")).

That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.

Let's go off and finish the job of commit 29ab586c by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60d
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).

Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.

And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.

Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Exclude RMII from modes that report 1 GbE support. Reduced MII supports
up to 100 MbE.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: NAleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210107195818.3878-1-olek2@wp.plSigned-off-by: NJakub Kicinski <kuba@kernel.org>

There is one GSWIP_MII_CFG register for each switch-port except the CPU
port. The register offset for the first port is 0x0, 0x02 for the
second, 0x04 for the third and so on.

Update the driver to not only restrict the GSWIP_MII_CFG registers to
ports 0, 1 and 5. Handle ports 0..5 instead but skip the CPU port. This
means we are not overwriting the configuration for the third port (port
two since we start counting from zero) with the settings for the sixth
port (with number five) anymore.

The GSWIP_MII_PCDU(p) registers are not updated because there's really
only three (one for each of the following ports: 0, 1, 5).

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Enable GSWIP_MII_CFG_EN also for internal PHYs to make traffic flow.
Without this the PHY link is detected properly and ethtool statistics
for TX are increasing but there's no RX traffic coming in.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Suggested-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

A user reports (slightly shortened from the original message):
  libphy: lantiq,xrx200-mdio: probed
  mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
  gswip 1e108000.switch lan: no phy at 2
  gswip 1e108000.switch lan: failed to connect to port 2: -19
  lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy

This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.

The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.

Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
  (the DSA framework just checks for the presence of the .port_vlan_add
  and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime

Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.

So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.

Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While trying to use the lantiq_gswip driver on one of my boards I made
a mistake when specifying the phy-mode (because the out-of-tree driver
wants phy-mode "gmii" or "mii" for the internal PHYs). In this case the
following error is printed multiple times:
  Unsupported interface: 3

While it gives at least a hint at what may be wrong it is not very user
friendly. Print the human readable phy-mode and also which port is
configured incorrectly (this hardware supports ports 0..6) to improve
the cases where someone made a mistake.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.

This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.

The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.

Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several spelling mistakes in dev_err messages. Fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds functions to add and remove static entries to and from the
forwarding database and dump the full forwarding database.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fast aging per port is not supported directly by the hardware, it is
only possible to configure a global aging time.

Do the fast aging by iterating over the MAC forwarding table and remove
all dynamic entries for a given port.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VLAN aware bridge offloading is similar to the VLAN unaware
offloading, this makes it possible to offload the VLAN bridge
functionalities.

The hardware supports up to 64 VLAN bridge entries, we already use one
entry for each LAN port to prevent forwarding of packets between the
ports when the ports are not in a bridge, so in the end we have 57
possible VLANs.

The VLAN filtering is currently only active when the ports are in a
bridge, VLAN filtering for ports not in a bridge is not implemented.

It is currently not possible to change between VLAN filtering and not
filtering while the port is already in a bridge, this would make the
driver more complicated.

The VLANs are only defined on bridge entries, so we will not add
anything into the hardware when the port joins a bridge if it is doing
VLAN filtering, but only when an allowed VLAN is added.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows to offload bridges with DSA to the switch hardware and do
the packet forwarding in hardware.

This implements generic functions to access the switch hardware tables,
which are used to control many features of the switch.

This patch activates the MAC learning by removing the MAC address table
lock, to prevent uncontrolled forwarding of packets between all the LAN
ports, they are added into individual bridge tables entries with
individual flow ids and the switch will do the MAC learning for each
port separately before they are added to a real bridge.

Each bridge consist of an entry in the active VLAN table and the VLAN
mapping table, table entries with the same index are matching. In the
VLAN unaware mode we configure everything with VLAN ID 0, but we use
different flow IDs, the switch should handle all VLANs as normal payload
and ignore them. When the hardware looks for the port of the destination
MAC address it only takes the entries which have the same flow ID of the
ingress packet.

The bridges are configured with 64 possible entries with these
information:
Table Index, 0...63
VLAN ID, 0...4095: VLAN ID 0 is untagged
flow ID, 0..63: Same flow IDs share entries in MAC learning table
port map, one bit for each port number
tagged port map, one bit for each port number
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the special tag in ingress only on the CPU port and not on all
ports. A packet with a special tag could circumvent the hardware
forwarding and should only be allowed on the CPU port where Linux
controls the port.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200)"
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The platform-device driver data is set on successful probe and will
never be NULL on remove (or we have much bigger problems).
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>