This patch allows a base driver to specify Direct Attach as the
type of port through the ethtool interface.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the CONFIG_SYSCTL ifdefs in x25_init into header.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the UP/DOWN state of VLANs is synchronized to the state of the
underlying device, meaning all VLANs are set down once the underlying
device is set down. This causes all routes to the VLAN devices to vanish.

Add a flag to specify a "loose binding" mode, in which only the operstate
is transfered, but the VLAN device state is independant.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support all three modes of macvlan at
runtime, extend the existing netlink protocol
to allow choosing the mode per macvlan slave
interface.

This depends on a matching patch to iproute2
in order to become accessible in user land.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The veth driver contains code to forward an skb
from the start_xmit function of one network
device into the receive path of another device.

Moving that code into a common location lets us
reuse the code for direct forwarding of data
between macvlan ports, and possibly in other
drivers.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a xfrm_state requires an authentication algorithm specified
either as xfrm_algo or as xfrm_algo_auth with a specific truncation
length. For compatibility, both attributes are dumped to userspace,
and we also accept both attributes, but prefer the new syntax.

If no truncation length is specified, or the authentication algorithm
is specified using xfrm_algo, the truncation length from the algorithm
description in the kernel is used.
Signed-off-by: NMartin Willi <martin@strongswan.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new XFRMA_ALG_AUTH_TRUNC attribute taking a xfrm_algo_auth as
argument allows the installation of authentication algorithms with
a truncation length specified in userspace, i.e. SHA256 with 128 bit
instead of 96 bit truncation.
Signed-off-by: NMartin Willi <martin@strongswan.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current implementation of max.burst ends up limiting new
data during cwnd decay period.  The decay is happening becuase
the connection is idle and we are allowed to fill the congestion
window.  The point of max.burst is to limit micro-bursts in response
to large acks.  This still happens, as max.burst is still applied
to each transmit opportunity.  It will also apply if a very large
send is made (greater then allowed by burst).
Tested-by: NFlorian Niederbacher <florian.niederbacher@student.uibk.ac.at>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

Recent attempt to remove deprecated socket options demonstrated
that removing options from the enum space will have severe
binary compatibility issues.  The reason is that it changes
the subsequent enum space and causes option values to be redefined.
To solve this, and to get rid of the ugly double statements for
every option, we simply convert to the #define scheme.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

The transport last_time_used variable is rather useless.
It was only used when determining if CWND needs to be updated
due to idle transport.  However, idle transport detection was
based on a Heartbeat timer and last_time_used was not incremented
when sending Heartbeats.  As a result the check for cwnd reduction
was always true.  We can get rid of the variable and just base
our cwnd manipulation on the HB timer (like the code comment sais).
We also have to call into the cwnd manipulation function regardless
of whether HBs are enabled or not.  That way we will detect idle
transports if the user has disabled Heartbeats.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

SCTP_GET_*_OLD stuffs are schedlued to be removed.

Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NWANG Cong <amwang@redhat.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

We currently send window update SACKs every time we free up 1 PMTU
worth of data.  That a lot more SACKs then necessary.  Instead, we'll
now send back the actuall window every time we send a sack, and do
window-update SACKs when a fraction of the receive buffer has been
opened.  The fraction is controlled with a sysctl.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

The "Invalid Stream Identifier" error has a 16 bit reserved
field at the end, thus making the parameter length be 8 bytes.
We've never supplied that reserved field making wireshark
tag the packet as malformed.
Reported-by: NChris Dischino <cdischino@sonusnet.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

This patch implement the sender side for SACK-IMMEDIATELY
extension.

  Section 4.1.  Sender Side Considerations

  Whenever the sender of a DATA chunk can benefit from the
  corresponding SACK chunk being sent back without delay, the sender
  MAY set the I-bit in the DATA chunk header.

  Reasons for setting the I-bit include

  o  The sender is in the SHUTDOWN-PENDING state.

  o  The application requests to set the I-bit of the last DATA chunk
     of a user message when providing the user message to the SCTP
     implementation.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

This patch implement the definition for SACK-IMMEDIATELY
extension.

Section 3.  The I-bit in the DATA Chunk Header

   The following Figure 1 shows the extended DATA chunk.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Type = 0    |  Res  |I|U|B|E|           Length              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                              TSN                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |        Stream Identifier      |     Stream Sequence Number    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Payload Protocol Identifier                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   \                                                               \
   /                           User Data                           /
   \                                                               \
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                                 Figure 1

   The only difference between the DATA chunk in Figure 1 and the DATA
   chunk defined in [RFC4960] is the addition of the I-bit in the flags
   field of the chunk header.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

To help grep games, rename iif to skb_iif
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With WEXT, it happens frequently that the SME
requests an authentication but then deauthenticates
right away because some new parameters came along.
Every time this happens we print a deauth message
and send a deauth frame, but both of that is rather
confusing. Avoid it by aborting the authentication
process silently, and telling cfg80211 about that.

The patch looks larger than it really is:
__cfg80211_auth_remove() is split out from
cfg80211_send_auth_timeout(), there's no new code
except __cfg80211_auth_canceled() (a one-liner) and
the mac80211 bits (7 new lines of code).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.

The rate control algorithms also need TX status, but
they don't require it.

Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.

This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A number of people have tried to add a wireless interface
(in managed mode) to a bridge and then complained that it
doesn't work. It cannot work, however, because in 802.11
networks all packets need to be acknowledged and as such
need to be sent to the right address. Promiscuous doesn't
help here. The wireless address format used for these
links has only space for three addresses, the
 * transmitter, which must be equal to the sender (origin)
 * receiver (on the wireless medium), which is the AP in
   the case of managed mode
 * the recipient (destination), which is on the APs local
   network segment

In an IBSS, it is similar, but the receiver and recipient
must match and the third address is used as the BSSID.

To avoid such mistakes in the future, disallow adding a
wireless interface to a bridge.

Felix has recently added a four-address mode to the AP
and client side that can be used (after negotiating that
it is possible, which must happen out-of-band by setting
up both sides) for bridging, so allow that case.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds SIOCX25SCAUSEDIAG, allowing X.25 programs to set the cause and
diagnostic fields.

Normally used to indicate status upon closing connections.
Signed-off-by: NAndrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRui Paulo <rpaulo@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJanakiram Sistla <janakiram.sistla@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJanakiram Sistla <janakiram.sistla@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.

It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1251 supports also that NVS is stored in a separate EEPROM, add support
for that.

kvalo: use platform data instead Kconfig and use kernel style
Signed-off-by: NDavid-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Herbert Xu a écrit :
> On Tue, Nov 17, 2009 at 04:26:04AM -0800, David Miller wrote:
>> Really, the link watch stuff is just due for a redesign.  I don't
>> think a simple hack is going to cut it this time, sorry Eric :-)
>
> I have no objections against any redesigns, but since the only
> caller of linkwatch_forget_dev runs in process context with the
> RTNL, it could also legally emit those events.

Thanks guys, here an updated version then, before linkwatch surgery ?

In this version, I force the event to be sent synchronously.

[PATCH net-next-2.6] linkwatch: linkwatch_forget_dev() to speedup device dismantle

time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105

real	0m0.266s
user	0m0.000s
sys	0m0.001s

real	0m0.770s
user	0m0.000s
sys	0m0.000s

real	0m1.022s
user	0m0.000s
sys	0m0.000s

One problem of current schem in vlan dismantle phase is the
holding of device done by following chain :

vlan_dev_stop() ->
	netif_carrier_off(dev) ->
		linkwatch_fire_event(dev) ->
			dev_hold() ...

And __linkwatch_run_queue() runs up to one second later...

A generic fix to this problem is to add a linkwatch_forget_dev() method
to unlink the device from the list of watched devices.

dev->link_watch_next becomes dev->link_watch_list (and use a bit more memory),
to be able to unlink device in O(1).

After patch :
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105

real    0m0.024s
user    0m0.000s
sys     0m0.000s

real    0m0.032s
user    0m0.000s
sys     0m0.001s

real    0m0.033s
user    0m0.000s
sys     0m0.000s
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This new event is called once for each unique net namespace in batched
unregister operations (with the argument set to a random device from
that namespace) and once per device in non-batched unregister
operations.

It allows us to factorize some device unregister work such as clearing the
routing cache.
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers ndo_get_stats() method need to perform txqueue stats folding.

Move folding from dev_get_stats() to a new dev_txq_stats_fold() function
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is for consistency with various ioctl() operations that include the
suffix "PGRP" in their names, and also for consistency with PRIO_PGRP,
used with setpriority() and getpriority().  Also, using PGRP instead of
GID avoids confusion with the common abbreviation of "group ID".

I'm fine with anything that makes it more consistent, and if PGRP is what
is the predominant abbreviation then I see no need to further confuse
matters by adding a third one.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow memory hotplug and hibernation in the same kernel

Memory hotplug and hibernation were exclusive in Kconfig.  This is
obviously a problem for distribution kernels who want to support both in
the same image.

After some discussions with Rafael and others the only problem is with
parallel memory hotadd or removal while a hibernation operation is in
process.  It was also working for s390 before.

This patch removes the Kconfig level exclusion, and simply makes the
memory add / remove functions grab the pm_mutex to exclude against
hibernation.

Fixes a regression - old kernels didn't exclude memory hotadd and
hibernation.
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

znet was including "wireless/i82593.h" (which is a bit wierd), and I
missed that when I relocated i82593.h to drivers/staging/wavelan.  Since
I don't have ISA turned-on in my normal .config, I didn't see the build
failures -- mea culpa!
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 38783e67.

It causes kernel bugzilla #14594
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function print_mac in net/ethernet/eth.c is marked __deprecated
and not used. Remove it.
Signed-off-by: NMarin Mitov <mitov@issp.bas.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes in the TX error propagation require additional checking
and masking of values returned from hard_start_xmit(), mainly to
separate cases where skb was consumed. This aim can be simplified by
changing the order of NETDEV_TX and NET_XMIT codes, because the latter
are treated similarly to negative (ERRNO) values.

After this change much simpler dev_xmit_complete() is also used in
sch_direct_xmit(), so it is moved to netdevice.h.

Additionally NET_RX definitions in netdevice.h are moved up from
between TX codes to avoid confusion while reading the TX comment.
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct nilfs_dat_group_desc is not used both in kernel and user spaces.
struct nilfs_palloc_group_desc is used instead.
Signed-off-by: NJiro SEKIBA <jir@unicus.jp>
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>