Drivers may override the WCE flag, in which case the DPOFUA flag in
MODE SENSE might differ from the check used to reject invalid FUA
bits in sbc_check_dpofua.  Also now that we reject invalid FUA
bits early there is no need to duplicate the same buggy check
down in the fileio code.

As the DPOFUA flag controls th support for FUA bits on read and
write commands as well as DPO key off all the checks off a single
helper, and deprecate the emulate_dpo and emulate_fua_read attributs.

This fixes various failures in the libiscsi testsuite.

Personally I'd prefer to also remove the emulate_fua_write attribute
as there is no good reason to disable it, but I'll leave that for
a separate discussion.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists.  So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.

(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: NMartin Petersen <martin.petersen@oracle.com>
Reviewed-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.

It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.

Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.

This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: NChristoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.

This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().

A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.

(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds a new target_core_fabric_ops callback for allowing fabric
drivers to expose a TPG attribute for signaling when a T10-PI protected
fabric wants to function with an un-protected device without T10-PI.

This specifically is to allow LIO to perform WRITE_STRIP + READ_INSERT
operations when functioning with non T10-PI enabled devices, seperate
from any available hw offloads the fabric supports.

This is done using a new se_sess->sess_prot_type that is set at fabric
session creation time based upon the TPG attribute.  It currently cannot
be changed for individual sessions after initial creation.

Also, update existing target_core_sbc.c code to honor sess_prot_type when
setting up cmd->prot_op + cmd->prot_type assignments.

(Add unlikely and !! boolean conversion in sbc_check_prot - Sagi)

Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.

It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.

It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: NMartin Svec <martin.svec@zoner.cz>
Cc: stable@vger.kernel.org
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com

This patch adds a force_pr_aptpl device attribute used to force SPC-3 PR
Activate Persistence across Target Power Loss (APTPL) operation.  This
makes PR metadata write-out occur during state change regardless if new
PERSISTENT_RESERVE_OUT CDBs have their APTPL feature bit set.

This is useful during H/A failover in active/passive setups where all PR
state is being re-created on a different node, driven by configfs backend
device + export layout and pre-loaded $DEV/pr/res_aptpl_metadata.

Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The target code has a rather generous helping of smp_mb__after_atomic()
throughout the code base.  Most atomic operations were followed by one
and none were preceded by smp_mb__before_atomic(), nor accompanied by a
comment explaining the need for a barrier.

Instead of trying to prove for every case whether or not it is needed,
this patch introduces atomic_inc_mb() and atomic_dec_mb(), which
explicitly include the memory barriers before and after the atomic
operation.  For now they are defined in a target header, although they
could be of general use.

Most of the existing atomic/mb combinations were replaced by the new
helpers.  In a few cases the atomic was sandwiched in
spin_lock/spin_unlock and I simply removed the barrier.

I suspect that in most cases the correct conversion would have been to
drop the barrier.  I also suspect that a few cases exist where a) the
barrier was necessary and b) a second barrier before the atomic would
have been necessary and got added by this patch.
Signed-off-by: NJoern Engel <joern@logfs.org>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.

This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.

For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.

For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.

For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses three of long standing issues wrt to Task
Aborted Status (TAS) handling.

The first is the incorrect assumption in core_tmr_handle_tas_abort()
that TASK_ABORTED status is sent for the task referenced by TMR
ABORT_TASK, and sending TASK_ABORTED status for TMR LUN_RESET on
the same nexus the LUN_RESET was received.

The second is to ensure the lun reference count is dropped within
transport_cmd_finish_abort() by calling transport_lun_remove_cmd()
before invoking transport_cmd_check_stop_to_fabric().

The last is to fix the delayed TAS handling to allow outstanding
WRITEs to complete before sending the TASK_ABORTED status. This
includes changing transport_check_aborted_status() to avoid
processing when SCF_SEND_DELAYED_TAS has not be set, and updating
transport_send_task_abort() to drop the SCF_SENT_DELAYED_TAS
check.
Signed-off-by: NAlex Leung <amleung21@yahoo.com>
Cc: Alex Leung <amleung21@yahoo.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This is not going to be supported soon - so drop it.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Some transports (iSCSI/iSER/SRP/FC) support hardware INSERT/STRIP
capabilities while other transports like loopback/vhost-scsi need
perform this is software.

This patch allows fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC
to signal the early LUN scan handling case where PROTECT CDB bits
are set, but no fabric buffer has been provided.

For transports which use generic new command these buffers have yet
to be allocated.

Also this way, target may support protection information
against legacy initiators (writes are inserted and reads
are stripped).

(Only set prot_pto for loopback during early special case - nab)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

SBC-3 mandates the protection checks that must be
performed in the rdprotect/wrprotect field. Use them.
According to backstore device pi_attributes and
cdb rdprotect/wrprotect field.

(Fix incorrect se_cmd->prot_type -> TARGET_PROT_NORMAL
 comparision in transport_generic_new_cmd - nab)
(Fix missing break in sbc_set_prot_op_checks - DanC + Sagi)
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The CMD_T_FAILED flag is set used in one place to record the result of a
trivial test, and it is only tested once, few lines later.  We might as
well make the code simpler and easier to read by directly doing the test
of "success" where we want to use it.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch fixes a percpu_ref_put race for se_lun->lun_ref in
transport_lun_remove_cmd() where ->lun_ref could end up being
put more than once per command via different target completion
and fabric release contexts.

It adds a cmpxchg() for se_cmd->lun_ref_active to ensure that
percpu_ref_put() is only ever called once per se_cmd.

This bug was manifesting itself as a LUN shutdown regression
bug in >= v3.13 code, where percpu_ref_kill() would end up
hanging indefinately due to the incorrect percpu_ref count.

(Change se_cmd->lun_ref_active from bool -> int to force at
 least a 4-byte cmpxchg with MIPS ll/sc ins. - Fengguang)
Reported-by: NTommy Apel <tommyapeldk@gmail.com>
Cc: Tommy Apel <tommyapeldk@gmail.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: NSagi Grimberg <sagig@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds support for DIF related CHECK_CONDITION ASC/ASCQ
exception cases into transport_send_check_condition_and_sense().

This includes:

  LOGICAL BLOCK GUARD CHECK FAILED
  LOGICAL BLOCK APPLICATION TAG CHECK FAILED
  LOGICAL BLOCK REFERENCE TAG CHECK FAILED

that used by DIF TYPE1 and TYPE3 failure cases.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds DIF related definitions to target_core_base.h
that includes enums for target_prot_op + target_prot_type +
target_prot_version + target_guard_type + target_pi_error.

Also included is struct se_dif_v1_tuple, along with changes
to struct se_cmd, struct se_dev_attrib, and struct se_device.

Also, add new se_subsystem_api->[init,format,free]_prot() callers
used by target core code to setup backend specific protection
information after the device has been configured.

Enums taken from Sagi Grimberg's original patch.

v2 changes:
  - Drop guard_type related definitions
  - Update target_prot_op + target_prot_ho definitions (Sagi)
  - Drop SCF_PROT + pi_prot_version flag
  - Add se_subsystem_api->format_prot() (Sagi)
  - Add hw_pi_prot_type device attribute

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch converts the temporary buffer in spc_emulate_inquiry() to
use dynamically allocated memory, instead of local stack memory.

Also bump SE_INQUIRY_BUF up to 1024 bytes to be safe when handling
multiple large SCSI name descriptors for EVPD=0x83.
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Add infrastructure for referrals.

v2 changes:

 - Fix unsigned long long division in core_alua_state_lba_dependent on
   32-bit  (Fengguang + Chen + Hannes)
 - Fix compile warning in core_alua_state_lba_dependent (nab)
 - Convert segment_* + sectors variables in core_alua_state_lba_dependent
   to u64 (Hannes)
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch allows FILEIO to update hw_max_sectors based on the current
max_bytes_per_io.  This is required because vfs_[writev,readv]() can accept
a maximum of 2048 iovecs per call, so the enforced hw_max_sectors really
needs to be calculated based on block_size.

This addresses a >= v3.5 bug where block_size=512 was rejecting > 1M
sized I/O requests, because FD_MAX_SECTORS was hardcoded to 2048 for
the block_size=4096 case.

(v2: Use max_bytes_per_io instead of ->update_hw_max_sectors)
Reported-by: NHenrik Goldman <hg@x-formation.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We should be including a descriptor referring to the target device
to allow identification of different TCM instances.

(nab: Bump SE_INQUIRY_BUF to 1024 bytes to handle 2x 256 byte SCSI names)
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Use a workqueue for processing ALUA state transitions; this allows
us to process implicit delay properly.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

During state transition we should be storing both the original
and the pending state.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

We should only allocate ALUA metadata if we're actually going
to write them.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Initialized but not used.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Commit 04f3b31b ("iscsi-target: Convert iscsi_session statistics to
atomic_long_t") removed the updating of these fields in iscsi (the only
fabric driver that ever touched these counters), and the core has no way
to report or otherwise use the values.  Remove the last remnants of
these counters.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The supported ALUA states might be different for individual
devices, so store it in a separate field.

(nab: Remove unnecessary line continuation)
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch converts the handful of se_device statistics to type
atomic_long_t, instead of using se_device->stats_lock when
incrementing these values.

More importantly, go ahead and drop the spinlock usage within
transport_lookup_cmd_lun() fast-path code.
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds a se_device->xcopy_lun that is used for local
copy offload I/O, instead of allocating + initializing a pseudo
se_lun for each received EXTENDED_COPY operation.

Also, move declaration of struct se_lun + struct se_port_stat_grps
ahead of struct se_device.
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Now with percpu refcounting for se_lun in place, go ahead and drop
the legacy per se_cmd accounting for se_lun shutdown.

This includes __transport_clear_lun_from_sessions(), the associated
transport_lun_wait_for_tasks() logic, along with a handful of now
unused se_cmd structure members and ->transport_state bits.

Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds percpu refcounting for se_lun access that allows the
association of an se_lun + se_cmd in transport_lookup_cmd_lun() to
occur without an extra list_head for tracking outstanding I/O during
se_lun shutdown.

This effectively changes se_lun shutdown logic to wait for outstanding
I/O percpu references to complete in transport_lun_remove_cmd() using
se_lun->lun_ref_comp, instead of explicitly draining the per se_lun
command list and waiting for individual se_cmd descriptor processing
to complete.

Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

No functional change.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds the Third Party Copy (3PC) bit to signal support
for EXTENDED_COPY within standard inquiry response data.

Also add emulate_3pc device attribute in configfs (enabled by default)
to allow the exposure of this bit to be disabled, if necessary.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Zach Brown <zab@redhat.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: NNicholas Bellinger <nab@daterainc.com>