Atm we have a few funny issues where we enable/disable shared
pll clocks. To make it clear that we are not required to enable/
disable the pch plls together with the other pch resources (and
so should keep it running when it's used by another pipe in
a shared pll configuration) add a comment.

This note is lifted from "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 9.d. of the enable
sequence:

"Configure and enable PCH DPLL, wait for PCH DPLL warmup (Can be
done anytime before enabling PCH transcoder)."

Since fixing the pll sharing code to no longer disable shared plls
if they're still in use is more involved, let's just stick with the
comment for now.

v2: Make the comment in the code clearer, to address questions raised
by Paulo Zanoni in review.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

My machine here has the correct ones already, but better safe
than sorry. IBX has different settings for that register, and
on IBX the device defaults match the recommended values. Hence
I did not add the respective writes for IBX.

LPT needs the same settings, but that has been done already

commit 4acf5186
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date:   Wed Jul 4 20:15:16 2012 -0300

    drm/i915: program FDI_RX TP and FDI delays

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For reference, see "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 4 of the enabling
sequence:

a. "Enable PCH FDI Receiver PLL, wait for warmup plus DMI latency
b. "Switch from Rawclk to PCDclk in FDI Receiver
c. "Enable CPU FDI Transmitter PLL, wait for warmup"

Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" We need to write the TU size register
of the fdi RX unit _before_ starting to train the link.

Note: The current code is actually correct as Paulo mentioned in
review, but it's a bit confusion since only the fdi rx/tx plls need to
be enabled before the cpu pipes/planes. Hence it's still a good idea
to move the TU_SIZE setting to the "right" spot in the sequence, to
better match Bspec.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Daniel's backmerge

commit c2fb7916
Merge: 29de6ce5 6f0c0580
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Oct 22 14:34:51 2012 +0200

    Merge tag 'v3.7-rc2' into drm-intel-next-queued

to solve conflicts blew up (either git or Daniel was trying to be too
clever for their own good; it's usually convenient to blame tools ;) and
caused the changes of

commit 0c96c65b
Author: Jani Nikula <jani.nikula@intel.com>
Date:   Wed Sep 26 18:43:10 2012 +0300

    drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag

in ironlake_crtc_mode_set() to be dropped.

Fix the call in ironlake_crtc_mode_set() again, and while at it, also fix
the new, copy-pasted haswell_crtc_mode_set() to use adjusted_mode.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

See the documentation for the DDI_FUNC_CTL register, EDP Input Select
bits: when the EDP input selection is B, the VTOTAL_B must be
programmed with the VTOTAL_EDP value, same thing for selection C.

V2: Use I915_READ as suggested by Daniel Vetter.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because the PIPECONF register is actually part of the CPU transcoder,
not the CPU pipe.

Ideally we would also rename PIPECONF to TRANSCONF to remind people
that they should use the transcoder instead of the pipe, but let's
keep it like this for now since most Gens still name it PIPECONF.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to check if any of the pipes is using TRANSCODER_EDP.

V2: DDI_BUF_CTL was renamed, so fix the usage here.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.

Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.

V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).

For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.

For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.

V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.

We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.

In other words:

Imagine the following case:
  xrandr --output eDP1 --auto --crtc 0
  xrandr --output eDP1 --off
  xrandr --output eDP1 --auto --crtc 2

After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.

So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On Ironlake we have one PCH transcoder and FDI per pipe, so we know
that if ironlake_crtc_driving_pch returns false we can disable the PCH
transcoder and we also know that when we disable the crtc we can also
disable the PCH transcoder.

On Haswell there is only 1 PCH transcoder and FDI and they can be used
by any CRTC. So if for one specific crtc haswell_crtc_driving_pch
returns false we can't assert anything about the state of the PCH
transcoder or the FDI link without checking if any other CRTC is using
the PCH.

So on this commit remove the "assert_fdi_{t,r}x_disabled" form
haswell_crtc_enable and also only disable FDI and the PCH transcoder
if the port being disabled was actually a PCH port (we only have one
port using PCH: the VGA port).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

By forking Ironlake and Haswell functions. The only callers are
{ironlake,haswell}_crtc_enable anyway, and this way we won't need to
add other checks on the Haswell version for the next gens.

V2: Even simpler, as pointed by Jani Nikula.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions were forked from their Ironlake versions, so now fix
the gen checks to reflect the fact that they will only run on Haswell.

It is worth noticing that we are not considering IBX/CPT possible on
Haswell anymore. So far on Haswell enablement we kept trying to still
consider IBX/CPT as a possibility with a Haswell CPU, but this was
never tested, I really doubt it will work with the current code and we
don't really have plans to support it. Future patches will remove the
IBX/CPT code from other Haswell functions. Notice that we still have a
WARN on haswell_crtc_mode_set in case we detect non-LPT PCH.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The last commit forked a Haswell version, so now we remove Haswell
code from these functions.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The way we enable and disable the PCH on Haswell changed considerably
since now we have only one PCH transcoder, so we can't keep the same
asserts and we also can't just unconditionally disable the PCH
transcoder for non-PCH outputs. So let's fork a Haswell version.

These new functions look exactly the same as the ironlake versions.
The next patches will introduce the differences.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.

Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.

Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have to write the correct values inside intel_dp_set_m_n and then
prevent these values from being overwritten later.

V2: Unconfuse double negation.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of relying on the register save/restore madness to do this.

To extract a bit of code call drm_mode_config_reset both on resume
and boot-up and move the hw state frobbing from the crt_init to the
->reset callback. The crt connector is the only one with a ->reset
callback, hence we can easily do this.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to check whether the _other plane is on our pipe, not whether
our plane is on the other pipe. Otherwise if not both pipes/planes are
active, we won't properly clean up the mess and set up our desired
plane->pipe mapping.

v2: Fixup the logic, I've totally fumbled it. Noticed by Chris Wilson.

v3: I've checked Bspec, and the flexible plane->pipe mapping is a
gen2/3 feature, so test for that instead of PCH_SPLIT

v4: Check whether we indeed have 2 pipes before checking the other
pipe, to avoid upsetting i845g/i865g. Noticed by Chris Wilson.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51265
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49838Tested-by: NDave Airlie <airlied@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #855gm
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This seems to be the root-cause that breaks resume on my i855gm when I
apply the "drm/i915: fixup the plane->pipe fixup code" patch. And that
code doesn't even run on my machine, so it's pure timing changes
causing the regression.

Furthermore resume has been constantly switching between working and
broken on this machine ever since kms support has been merged,
seemingly with no related change as a root cause. And always with the
same symptoms of the backlight lighting up, but the lvds panel only
displaying black.

Also, of both i855gm variants only one is in the table. And in the
past we've only ever removed entries from this quirk table because it
breaks things.

So let's just remove it - in case there's indeed a bios out there
relying on a running pipe A, we can add back in a more precise quirk
entry, like all the others (save for i830/i845).

Tested-by: Chris Wilson <chris@chris-wilson.co.uk> #855gm
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So WARN in case they're not. It also does not make any sense to
wait_for_vblank at this point.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Problems with the previous code:
  - HDMI just uses WRPLL1 for everything, so dual head cases might not
    work sometimes.
  - At encoder->mode_set we just write the PLL register without doing
    any kind of check (e.g., check if the PLL is already being used).
  - There is no way to fail and return error codes at
    encoder->mode_set.
  - We write to PORT_CLK_SEL at mode_set and we never disable it.
  - Machines hang due to wrong clock enable/disable sequence.

So here we rewrite the code, making it a little more like the
pre-Haswell PLL mode set code:
  - Check PLL availability at ironlake_crtc_mode_set.
  - Try to use both WRPLLs.
  - Check if PLLs are used before actually trying to use them, and
    properly fail with error messages.
  - Enable/disable PORT_CLK_SEL at the right place.
  - Add some WARNs to check for bugs.

The next improvement will be to try to reuse PLLs if the timings
match, but this is content for another patch and it's already
documented with a TODO comment.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's a copy of ironlake_set_pipeconf with 2 differences:
  - There is no BPC field to set.
  - The interlaced mask is now 2 bits instead of 3.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On ironlake_crtc_mode_set, WARN if not using IBX or CPT.

On haswell_crtc_mode_set, only run IBX/CPT code on IBX/CPT. I am still
not sure whether IBX/CPT will be possible with a Haswell CPU, so leave
the code there for now and put a WARN in case we spot it.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's just a copy of ironlake_crtc_mode_set.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously we were enabling it at mode_set but never disabling. Let's
follow the mode set sequence.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And the right time is exactly after/before changing PIPE_CONF. See the
documentation about the mode set sequence.

This code is not inside any encoder-specific callback because
DDI_FUNC_CTL is part of the pipe, so it is used by all encoders.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Right now, we're trying to enable LCPLL at every mode set, but we're
never disabling it. Also, we really don't want to be disabling LCPLL
since it requires a very complex disable/enable sequence. This
register should really be set by the BIOS and we shouldn't be touching
it. Still, let's try to check its value and print some errors in case
we find something wrong. We're also adding intel_ddi_get_cdclk_freq
which will be used later in other places.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've discovered this on my ivb machine while stress-testing the new
flip_tests. Only harmful effect observed is that the timestamp is a
bit bogus.

Note that this is empirical duct-tape: I've noticed that we seem to
only ever miss the very first vblank irq right after enabling the
pipe. And with this hack applied I couldn't reproduce the failure case
anywhere else any more.
Tested-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we correctly generate it, this hack is no longer required (and
might actually paper over a serious bug).

pageflip timestamps are sanity check in the latest version of the flip-test
in intel-gpu-tools.

v2: Also remove the gettimeofday(&now) which is no longer used.
Noticed by Mario Kleiner.

Reviewed-by: mario.kleiner@tuebingen.mpg.de
Tested-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Version 2: call intel_set_pipe_timings from both i9xx_crtc_mode_set
and ironlake_crtc_mode_set, instead of just ironlake, as requested by
Daniel Vetter.

The problem caused by calling this function from i9xx_crtc_mode_set
too is that now on i9xx we write to PIPESRC before writing to DSPSIZE
and DSPPOS. I could not find any evidence in our documentation that
this won't work, and the docs actually say the pipe registers should
be set before the plane registers.

Version 3: don't remove pipeconf bits on i9xx_crtc_mode_set.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was meant to be the purpose of the
intel_crtc_wait_for_pending_flips() function which is called whilst
preparing the CRTC for a modeset or before disabling. However, as Ville
Syrjala pointed out, we set the pending flip notification on the old
framebuffer that is no longer attached to the CRTC by the time we come
to flush the pending operations. Instead, we can simply wait on the
pending unpin work to be finished on this CRTC, knowning that the
hardware has therefore finished modifying the registers, before proceeding
with our direct access.

Fixes i-g-t/flip_test on non-pch platforms. pch platforms simply
schedule the flip immediately when the pipe is disabled, leading
to other funny issues.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Added i-g-t note and cc: stable]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fixed correct min, max vco limits and dip ctl reg
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Eventhough Valleyview display block is derived from Cantiga, VLV
supports eDP. So, added eDP checks in i9xx_crtc_mode_set path.

v2: use different DPIO_DIVISOR values for VGA, DP and eDP
v3: fix DPIO value calculation to use same values for all display
interfaces
v4: removed unconditional enabling of 6bpc dithering based on comments
from Daniel & Jani Nikula. Also changed the display enabling order to
force eDP detection first.
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In valleyview voltageswing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric.

Cleaned up DPLL calculations for Valleyview to support multi display
configurations.

v2: Based on Daniel's feedbacak, moved crt hotplug detect work around as separate
patch. Also moved i9xx_update_pll_dividers to i8xx_update_pll and
i9xx_update_pll.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NGajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: drop spurious whitespace changes.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

m n tu register offset has changed in Valleyview. Also fixed DP limit
frequencies.
Signed-off-by: NVijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>