Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 03 10月, 2007 3 次提交
  3. 22 9月, 2007 1 次提交
  5. 20 9月, 2007 1 次提交
  7. 13 9月, 2007 1 次提交
  9. 07 9月, 2007 2 次提交
  11. 22 8月, 2007 3 次提交
  13. 20 8月, 2007 2 次提交
  15. 10 7月, 2007 2 次提交
    • T
      [POWERPC] Create a dummy zImage if no valid platform has been selected · 4bb09281
      由 Tony Breeds 提交于 
      This simply prevents a build error if no platform is selected.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      4bb09281
    • G
      [POWERPC] PS3: Bootwrapper support. · bafdb645
      由 Geoff Levand 提交于 
      Add support to build the PS3 flash rom image and remove some unneeded
lmb calls.

The PS3's lv1 loader supports loading gzipped binary images from flash
rom to addr zero. The loader enters the image at addr 0x100.

In this implementation a bootwrapper overlay is use to arrange for the
kernel to be loaded to addr zero and to have a suitable bootwrapper
entry at 0x100.  To construct the rom image, 0x100 bytes from offset
0x100 in the kernel is copied to the bootwrapper symbol
__system_reset_kernel.  The 0x100 bytes at the bootwrapper symbol
__system_reset_overlay is then copied to offset 0x100.  At runtime the
bootwrapper program copies the 0x100 bytes at __system_reset_kernel to
addr 0x100.

zImage.ps3 is a wrapped image that contains a flat device tree, an lv1
compatible entry point, and an optional initrd.  otheros.bld is the gzip
compresed rom image built from zImage.ps3.  otheros.bld is suitable for
programming into the PS3 boot flash memory.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      bafdb645
  17. 25 6月, 2007 3 次提交
  19. 14 6月, 2007 2 次提交
    • D
      [POWERPC] Consolidate cuboot initialization code · 85aecac8
      由 David Gibson 提交于 
      The various cuboot platforms (i.e. pre-device tree aware u-boot for
83xx, 85xx and Ebony) share a certain amount of code for parsing the
boot parameters.  To a certain extent that's inevitable, since they
platforms have different definitions of the bd_t structure.  However,
with some macro work and a helper function, this patch improves the
situation a bit.

In the process, this fixes a bug on Ebony, which was incorrectly
handling the parameters passed form u-boot for the command line (the
bug was copied from 83xx and 85xx which have subsequently been fixed).
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      85aecac8
    • D
      [POWERPC] Split low-level OF-related bootloader code into separate files · 2e601613
      由 David Gibson 提交于 
      Currently, all OF-related code in the bootloader is contained in of.c.
of.c also provides the platform specific things necessary to boot on
an OF platform.

However, there are platforms (such as PReP) which can include an OF
implementation, but are not bootable as pure OF systems.  For use by
such platforms, this patch splits out the low-level parts of the OF
code (call_prom() and various wrappers thereof) into a new oflib.c
file.  In addition, the code related to bootwrapper console output via
OF are moved to a new ofconsole.c file.  Both these files are included
in the wrapper.a library where they can be used by both full-OF and
partial OF platforms.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      2e601613
  21. 02 6月, 2007 3 次提交
  23. 17 5月, 2007 3 次提交
  25. 12 5月, 2007 5 次提交
    • M
      [POWERPC] Add bootwrapper support for Motorola PrPMC2800 platform · c368d921
      由 Mark A. Greer 提交于 
      The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively.  There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.

The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant.  From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly.  If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.

Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      c368d921
    • M
      [POWERPC] Add bootwrapper support for Marvell/mv64x60 I2C · ae4b3fbc
      由 Mark A. Greer 提交于 
      Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD).  The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.

Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      ae4b3fbc
    • M
      [POWERPC] Add bootwrapper support for Marvell MPSC · e12deb84
      由 Mark A. Greer 提交于 
      The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console.  This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      e12deb84
    • M
      [POWERPC] Add bootwrapper support for Marvell/mv64x60 hostbridge · 0f81b11d
      由 Mark A. Greer 提交于 
      The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).

So, the missing configuration needs to be done in either the bootwrapper
or in the kernel.  To keep the kernel as clean as possible, it is done
in the bootwrapper.  Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).

Table of routines and the windows they configure:
	mv64x60_config_ctlr_windows()	ENET->System Memory
					MPSC->System Memory
					IDMA->System Memory

	mv64x60_config_pci_windows()	PCI MEM->System Memory
					PCI I/O->Bridge's Registers

	mv64x60_config_cpu2pci_window()	CPU->PCI MEM
					CPU->PCI I/O
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      0f81b11d
    • M
      [POWERPC] Add Makefile rules to wrap dts file in zImage · 916066d5
      由 Mark A. Greer 提交于 
      Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.

Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time.  This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees.  By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.

The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: NMark A. Greer <mgreer@mvista.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
      916066d5
  27. 08 5月, 2007 2 次提交
  29. 07 5月, 2007 2 次提交
  31. 02 5月, 2007 1 次提交
  33. 30 4月, 2007 1 次提交
  35. 27 4月, 2007 2 次提交
  37. 24 4月, 2007 1 次提交