Skip to content

K
Kernel

openeuler / Kernel
大约 1 年 前同步成功

通知 6
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 02 12月, 2006 8 次提交
    • A
      USB: OHCI: remove stale testing code from root-hub resume · 565402ba
      由 Alan Stern 提交于 
      This patch (as811) removes some stale testing code from the root-hub
resume routine in ohci-hcd.  It also adds a spin_lock_irq() call that
inadvertently got left out of an error pathway.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      565402ba
    • E
      USB: kmemdup() cleanup in drivers/usb/ · 5d7efe5b
      由 Eric Sesterhenn 提交于 
      replace open coded kmemdup() to save some screen space,
and allow inlining/not inlining to be triggered by gcc.
Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      5d7efe5b
    • A
      USB: OHCI: disable RHSC inside interrupt handler · 052ac01a
      由 Alan Stern 提交于 
      This patch (as808b) moves the Root Hub Status Change interrupt-disable
code in ohci-hcd back into the interrupt handler proper, to avoid the
chance of adverse interactions with mediocre hardware implementations.

It also deletes the root-hub status timer from within the interrupt-enable
routine.  There's no need to poll for status any more once interrupts are
re-enabled.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      052ac01a
    • A
      USB: ohci-hcd: fix compiler warning · b1878440
      由 Alan Stern 提交于 
      This patch (as806) fixes a compiler warning when ohci-hcd is built
with CONFIG_PM turned off.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      b1878440
    • A
      USB core: don't match interface descriptors for vendor-specific devices · 93c8bf45
      由 Alan Stern 提交于 
      This patch (as804) makes USB driver matching ignore the interface
class, subclass, and protocol if the device class is Vendor Specific.
Drivers can override this policy by specifying a Vendor ID as part
of the match; then vendor-specific matches are allowed.

Linus Walleij has reported a problem this patch fixes.  When a
particular mass-storage device is switched from mass-storage mode to
Media Transfer Protocol, the interface class remains set to mass-storage
and usb-storage binds to it erroneously, even though the device class
changes to Vendor-Specific.

This may cause a problem for some drivers until their match records can
be updated to include Vendor IDs.  But if it does, then those records
were broken to begin with.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      93c8bf45
    • A
      USB HID: Handle STALL on interrupt endpoint · 6d8fc4d2
      由 Alan Stern 提交于 
      The USB HID driver doesn't include any code to handle a STALL on the
interrupt endpoint.  While this may be uncommon, it does happen
sometimes.  This patch (as805) adds a fix.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      6d8fc4d2
    • I
      usb hub: fix root hub code so it takes more than 15 devices per root hub · 88fafff9
      由 inaky@linux.intel.com 提交于 
      Wireless USB Host Controllers accept a large number of devices per
host, which shows up as a large number of ports in its root hub.

When the number of ports in a hub device goes over 16, the activation
of the hub fails with the cryptic message in klogd.

hub 2-0:1.0: activate --> -22

Following this further, it was seen that:

hub_probe()
  hub_configure()
    generates pipe number

    pseudo allocates buffer 'maxp' bytes in size using usb_maxpacket()

      The endpoint descriptor for a root hub interrupt endpoint is
      declared in
      drivers/usb/core/hcd.c:hs_rh_config_descriptor and declares it
      to be size two (supporting 15 devices max).

    hub_activate()
      usb_hcd_submit_urb()
        rh_urb_enqueue()
          urb->pipe is neither int nor ctl, so it errors out
            rh_queue_status()
              Returns -EINVAL because the buffer length is smaller
              than the minimum needed to report all the hub port
              bits as in accordance with USB2.0[11.12.3]. There has
              to be trunc((PORTS + 1 + 7) / 8) bytes of space at
              least.

Alan Stern confirmed that the reason for reading maxpktsize and not
the right amount is because some hubs are known to return more data
and thus cause overflow. 

So this patch simply changes the code to make the interrupt endpoint's
max packet size be at least the minimum required by USB_MAXCHILDREN
(instead of a fixed magic number) and add documentation for that. This
way we are always ahead of the limit.
Signed-off-by: NInaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      88fafff9
    • I
      usb/hub: allow hubs up to 31 children · 43705251
      由 inaky@linux.intel.com 提交于 
      Current Wireless USB host hardware (Intel i1480 for example) allows up
to 22 devices to connect, thus bringing up the max number of children
in the WUSB Host Controller to 22 'fake' ports. Upcoming hardware
might raise that limit.

Makes almost no difference to go to 31, as the bit arrays are
byte-aligned (plus an extra bit in general), so 22 bits fit in 4 bytes
as 31 do.

As well, the only other array that depends on USB_MAXCHILDREN is
'struct usb_hub->indicator'. By declaring it 'u8' instead of 'enum
hub_led_mode', we reduce the size of each entry from 4 bytes (in i386)
to 1, which will add as we when are doubling USB_MAXCHILDREN
(with 16 the size of that array is 64 bytes, with 31 would be 128; by
using u8 that goes down to 31 bytes).
Signed-off-by: NInaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      43705251
  3. 30 11月, 2006 5 次提交
  5. 29 11月, 2006 24 次提交
  7. 28 11月, 2006 3 次提交