Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).

Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device.  As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.

If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
  to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code:  Activation of this features should be
  left to the boards using the chips since it also affects external devices
  tied to BCLK, and only the board designers know whether it is safe to
  enable.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/common/cputable.c

There are no in-tree users, so remove them.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Tested on Db1200.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch attempts to modernize core Alchemy interrupt handling code.

- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
  contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
  the remaining (gpio-based) interrupt sources; update all boards
  accordingly.

Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c

Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Share some code and merge small files:
- Extract the prom init code from all devboard files (they only differ in
  memory configuration).
- Merge the irq configuration into board setup code.
- Merge smaller files into board setup code.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/alchemy/devboards/db1x00/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1000/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1000/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1100/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1100/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1200/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1500/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1500/irqmap.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1550/init.c
 delete mode 100644 arch/mips/alchemy/devboards/pb1550/irqmap.c
 create mode 100644 arch/mips/alchemy/devboards/prom.c

This should ease sharing of common devboard code.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.

A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@s2@
long e;
position p;
@@

strict_strtol@p(...,&e)

@@
position p != s2.p;
type T;
T e;
@@

- strict_strtol@p
+ strict_strtoul
  (...,&e)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It's more than the au1000 these days.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>