We store a SW state of the t11_t12 timing in 100usec units but have to
program it in 100msec as required by HW. The rounding used during
programming means there will be a mismatch between the SW and HW states
of this value triggering a "PPS state mismatch" error. Avoid this by
storing the already rounded-up value in the SW state.

Note that we still calculate panel_power_cycle_delay with the finer
100usec granularity to avoid any needless waits using that version of
the delay.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103903
Cc: joks <joks@linux.pl>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129175137.2889-1-imre.deak@intel.com

Two bits:
- check actual atomic state, the legacy stuff can only be looked at
  from within the atomic_commit_tail function, since it's only
  protected by ordering and not by any locks.

- Make sure we don't wreak the work an ongoing nonblocking commit is
  doing.

v2: We need the crtc lock too, because a plane update might change it
without having to acquire the connection_mutex (Maarten). Use
Maarten's changes for this locking, while keeping the logic that uses
the connection->commit->hw_done signal for syncing with nonblocking
commits.

v3: The initial state objects from the hw state readout do not have a
commit object. Check for that (spotted by CI).

v4: Fix deadlock from jumping to put_power with locks still held.
    (mlankhorst)

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=103336
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99272Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113160140.22679-1-maarten.lankhorst@linux.intel.com

Changes since v1:
- Only pass crtc_state, not crtc.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110113503.16253-8-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

IPS can only be enabled if the primary plane is visible, so
first make sure sw state matches hw state by waiting for hw_done.

After this pass crtc_state to intel_dp_sink_crc() so that can be used,
instead of using legacy pointers.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110113503.16253-7-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Commit 78597996 (drm/i915/bxt: Fix PPS lost state after suspend
breaking eDP link training) renamed the function to
intel_power_sequencer_reset() but forgot to update comment.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114004638.5186-1-lucas.demarchi@intel.com

Eliminate a ton of pointless 'dev' variables in the DP code, and pass
around 'dev_priv' instead of 'dev'.

v2: Rebase
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171109152758.32257-1-ville.syrjala@linux.intel.com

No need to pass 'dev' or 'dev_priv' when the function already takes
'intel_dp'. Also let's prefer passing 'dev_priv' instead of 'dev'
when we have to pass one or the other.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031205123.13123-10-ville.syrjala@linux.intel.comAcked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

Remove intel_digital_port->port and replace its users with
intel_encoder->port. intel_encoder->port is a superset of
intel_digital_port->port, and it works correctly even for
MST encoders.

v2: Eliminate a few dp_to_dig_port()->base.port cases too (DK)

Performed with cocci:
@@
@@
struct intel_digital_port {
       ...
-       enum port port;
       ...
}

@@
struct intel_digital_port *D;
expression E;
@@
- D->port = E;

@@
struct intel_digital_port *D;
@@
- D->port
+ D->base.port

@
expression E;
@@
(
- dp_to_dig_port(E)->port
+ dp_to_dig_port(E)->base.port
|
- enc_to_dig_port(E)->port
+ to_intel_encoder(E)->port
)

@@
expression E;
@@
- to_intel_encoder(&E->base)
+ E

@@
struct intel_digital_port *D;
identifier I, M;
@@
  I = &D->base
<...
(
- D->base.M
+ I->M
|
- &D->base
+ I
)
...>

@@
identifier D;
expression E;
identifier M;
@@
 D = enc_to_dig_port(&E->base)
<...
(
- D->base.M
+ E->M
|
- &D->base
+ E
)
...>

@@
identifier D, DP;
expression E;
identifier M;
@@
 DP = enc_to_intel_dp(&E->base)
<...
(
- dp_to_dig_port(DP)->base.M
+ E->M
|
- &dp_to_dig_port(DP)->base
+ E
)
...>

@@
expression E;
identifier M;
@@
(
- enc_to_dig_port(&E->base)->base.M
+ E->M
|
- enc_to_dig_port(&E->base)->base
+ E
|
- enc_to_mst(&E->base)->primary->base.port
+ E->port
)

@@
expression E;
identifier D;
@@
- struct intel_digital_port *D = E;
... when != D

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171109152434.32074-1-ville.syrjala@linux.intel.com

Rather than digging through encoder->crtc and crtc->config in the
DPIO PHY functions, pass down the correct crtc state from the caller.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031205123.13123-6-ville.syrjala@linux.intel.comAcked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

Extract the current crtc from the crtc state rather than via
the legacy encoder->crtc pointer whenever possible.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031205123.13123-2-ville.syrjala@linux.intel.comAcked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

Explicitly pass the crtc and connector states into the audio
code enable/disable hooks, and plumb them all the way down.

This gets rid of almost all crtc->config and encoder->crtc
uses. The one place where we still use them is
i915_audio_component_sync_audio_rate() since that gets called from
the audio driver and we don't have explicit states around then.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171030184654.17429-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Currently the DDI encoder->type will change at runtime depending on
what kind of hotplugs we've processed. That's quite bad since we can't
really trust that that current value of encoder->type actually matches
the type of signal we're trying to drive through it.

Let's eliminate that problem by declaring that non-eDP DDI port will
always have the encoder type as INTEL_OUTPUT_DDI. This means the code
can no longer try to distinguish DP vs. HDMI based on encoder->type.
We'll leave eDP as INTEL_OUTPUT_EDP, since it'll never change and
there's a bunch of code that relies on that value to identify eDP
encoders.

We'll introduce a new encoder .compute_output_type() hook. This allows
us to compute the full output_types before any encoder .compute_config()
hooks get called, thus those hooks can rely on output_types being
correct, which is useful for cloning on oldr platforms. For now we'll
just look at the connector type and pick the correct mode based on that.
In the future the new hook could be used to implement dynamic switching
between LS and PCON modes for LSPCON.

v2: Fix BXT/GLK PPS explosion with DSI/MST encoders
v3: Avoid the PPS warn on pure HDMI/DVI DDI encoders by checking dp.output_reg
v4: Rebase
v5: Populate output_types in .get_config() rather than in the caller
v5: Split out populating output_types in .get_config() (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-3-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Rather than having the caller of .get_config() set output_types based on
encoder->type, let's just have .get_config() itself populate
output_types. This way we are isolated from encoder->type, which won't
be useable for this purpose anyway soon (at least for DDI encoders).

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-2-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

DP dongles may signal downstream HPD via short HPD pulses. Setting the
sink to DPMS off apparently kills the downstream HPD (at least on my
DP->VGA dongle), so skip the DPMS off for such dongles when we turn
off the port.

v2: Deal with DDI as well by moving the check into
    intel_dp_sink_dpms() (Dhinakaran)

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Pablo <pablodebiase@nanalysis.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103472
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99114Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027094523.9317-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Some minor drive-by cleanups.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026142932.17737-2-jani.nikula@intel.com

Per my reading of the eDP spec, DP_DPCD_DISPLAY_CONTROL_CAPABLE bit in
DP_EDP_CONFIGURATION_CAP should be set if the eDP display control
registers starting at offset DP_EDP_DPCD_REV are "enabled". Currently we
check the bit before reading the registers, and DP_EDP_DPCD_REV is the
only way to detect eDP revision.

Turns out there are (likely buggy) displays that require eDP 1.4+
features, such as supported link rates and link rate select, but do not
have the bit set. Read the display control registers
unconditionally. They are supposed to read zero anyway if they are not
supported, so there should be no harm in this.

This fixes the referenced bug by enabling the eDP version check, and
thus reading of the supported link rates. The panel in question has 0 in
DP_MAX_LINK_RATE which is only supported in eDP 1.4+. Without the
supported link rates method we default to RBR which is insufficient for
the panel native mode. As a curiosity, the panel also has a bogus value
of 0x12 in DP_EDP_DPCD_REV, but that passes our check for >= DP_EDP_14
(which is 0x03).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103400Reported-and-tested-by: NNicolas P. <issun.artiste@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026142932.17737-1-jani.nikula@intel.com

Make BXT less special by following the CNL approach and handling
it in intel_ddi_dp_voltage_max() alognside every other DDI platform.

v2: Clean up the argument types to bxt_ddi_vswing_sequence() while at it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-6-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

Per BSpec, 400us is "BDW+ Do not use this setting." - not just PORT_A.
Set BDW to 600us unconditionally.

v2:
-Split in to two patches (Rodrigo)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012213037.4245-2-james.ausmus@intel.com

Rename DP_AUX_CH_CTL_TIME_OUT_1600us to DP_AUX_CH_CTL_TIME_OUT_MAX, as
the meaning of the (3 << 26) value varies per platform, but it's always the
maximum timeout for that platform. Pre-CNL it means 1600us, and for CNL
it means 3200us.

v2:
-Split in to two patches (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012213037.4245-1-james.ausmus@intel.com

Add the minimal amount of PSR tracking into the crtc state. This allows
precomputing the possibility of using PSR correctly, and it means we can
safely call the psr enable/disable functions for any DP endcoder.

As a nice bonus we get rid of some more crtc->config usage, which we
want to kill off eventually.

v2: Fix 'goto unlock' fail in intel_psr_enable() (Jani)
    Check intel_dp_is_edp() in is_edp_psr() (Jani)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012130201.21318-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Get rid of redundant intel_dp_num_rates(). We can simply look at the
rate and limit based on that.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171009092959.29021-3-jani.nikula@intel.com

Turn intel_dp_source_supports_hbr2() into a simple helper to query the
pre-filled source rates array, and move the conditions about which
platforms support which rates to the single point of truth in
intel_dp_set_source_rates().

This also reduces the code paths you have to think about in the source
rates initialization in intel_dp_set_source_rates(), making it easier to
grasp.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171009092959.29021-2-jani.nikula@intel.com

For this specific PCI device, the eDP panel requires a higher panel
power cycle delay of 1300ms where the minimum spec requirement of panel
power cycle delay is 500ms. This fix in combination with correct
timestamp at which we get the panel power off time fixes the dP AUX CH
timeouts seen on various IGT tests.

Fixes: c99a259b ("drm/i915/edp: Add a T12 panel delay quirk to fix
DP AUX CH timeouts")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101518
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507073845-13420-2-git-send-email-manasi.d.navare@intel.com
(cherry picked from commit c02b8fb4)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Kernel stores the time in jiffies at which the eDP panel is turned
off. This should be obtained after the panel is off (after the
wait_panel_off). When we next attempt to turn the panel on, we use the
difference between the timestamp at which we want to turn the panel on
and timestamp at which panel was turned off to ensure that this is equal
to panel power cycle delay and if not we wait for the remaining
time. Not waiting for the panel power cycle delay can cause the panel to
not turn on giving rise to AUX timeouts for the attempted AUX
transactions.

v2:
* Separate lines for bugzilla (Jani Nikula)
* Suggested by tag (Daniel Vetter)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101518
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507135706-17147-1-git-send-email-manasi.d.navare@intel.com
(cherry picked from commit cbacf02e)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

For this specific PCI device, the eDP panel requires a higher panel
power cycle delay of 1300ms where the minimum spec requirement of panel
power cycle delay is 500ms. This fix in combination with correct
timestamp at which we get the panel power off time fixes the dP AUX CH
timeouts seen on various IGT tests.

Fixes: c99a259b ("drm/i915/edp: Add a T12 panel delay quirk to fix
DP AUX CH timeouts")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101518
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507073845-13420-2-git-send-email-manasi.d.navare@intel.com

Kernel stores the time in jiffies at which the eDP panel is turned
off. This should be obtained after the panel is off (after the
wait_panel_off). When we next attempt to turn the panel on, we use the
difference between the timestamp at which we want to turn the panel on
and timestamp at which panel was turned off to ensure that this is equal
to panel power cycle delay and if not we wait for the remaining
time. Not waiting for the panel power cycle delay can cause the panel to
not turn on giving rise to AUX timeouts for the attempted AUX
transactions.

v2:
* Separate lines for bugzilla (Jani Nikula)
* Suggested by tag (Daniel Vetter)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101518
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144Suggested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507135706-17147-1-git-send-email-manasi.d.navare@intel.com

We already print training pattern used during link training and also
print if the source or sink does not support TPS3 for HBR2 link rates,
see intel_dp_training_pattern().
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170918222141.4674-5-dhinakaran.pandiyan@intel.com

The buffer size defined is 16 bytes whereas only 14 bytes are read. Add a
macro to avoid this discrepancy.
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NJames Ausmus <james.ausmus@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170918222141.4674-3-dhinakaran.pandiyan@intel.com

Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.

v5: pure rename
v6: fix

Credits-to: Coccinelle

@@
identifier n;
@@
(
-	i915.n
+	i915_modparams.n
)
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com

Most of our DP encoder hooks are split into per-platform variants.
.disable() an exception, and thus it's a bit messy. Let's split it
up as well. We'll leave the common parts in a helper called by
each platform specific hook. Now each platform has mostly its own
hooks. Some hooks are still shared between vlv and chv, and between
g4x and ilk. None of the remaining shared hooks have any platform
checks in them however so duplicating them doesn't seem particularly
useful.

There is a subtle change on VLV/CHV where we now disable PSR before
audio, whereas before we disabled PSR after audio. That should be
totally fine, and PSR is disabled by default anyway. Jani also pointed
out to me that PSR + audio doesn't seem like a particularly realistic
combination.

v2: Drop the PSR HAS_DDI check here (Rodrigo)
    Pimp up the commit message a bit based on a chat with Jani

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170920151251.5961-1-ville.syrjala@linux.intel.com

It is safe to call intel_psr_disable() on a platform without PSR. We
don't have such a check when calling intel_psr_enable() either.

v2: Don't drop the HAS_DDI check quite yet (Rodrigo)
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170920151236.5864-1-ville.syrjala@linux.intel.com

Some platforms do not support PSR and DRRS simultaneously.
Visual artifacts and flickering were reported on BDW HP Spectre
x360 Convertible. Deferring to PSR when both PSR and DRRS are
supported by the panel.

V2: Minor code-style changes suggested by Rodrigo
V3: Add a WARN_ON during PSR init suggested by Dhinakaran
    Correct debug message,title suggested by Jani

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101111
Cc: Nicholas Stommel <nicholas.stommel@gmail.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRadhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170914181641.24393-1-radhakrishna.sripada@intel.com

This patch fixes the DP AUX CH timeouts observed during CI runs causing
CI Failures on a specific PCI device. This issue was fixed previously
by adding a quirk but looks like we need to increase this delay even more
in order to get rid all the DP AUX CH timeouts.

Fixes: c99a259b ("drm/i915/edp: Add a T12 panel delay quirk to fix
DP AUX CH timeouts")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502823591-25310-1-git-send-email-manasi.d.navare@intel.com
(cherry picked from commit e8f345e0)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This patch fixes the DP AUX CH timeouts observed during CI runs causing
CI Failures on a specific PCI device. This issue was fixed previously
by adding a quirk but looks like we need to increase this delay even more
in order to get rid all the DP AUX CH timeouts.

Fixes: c99a259b ("drm/i915/edp: Add a T12 panel delay quirk to fix
DP AUX CH timeouts")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101144Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502823591-25310-1-git-send-email-manasi.d.navare@intel.com

Let's decouple bxt, glk and cnl dp signal levels
from other DDIs to avoid confusion.

No functional change. Only a reorg to avoid messing
with currently working DP signal levels when
moving voltage swing sequences around to match spec.

v2: ddi_signal_levels is also called from other ddi
    platforms, so don't remove IS_GEN9_BC check from
    skl_ddi_set_iboos. (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-2-rodrigo.vivi@intel.com

The enable/disable/etc. encoder hooks aren't supposed to alter the
state(s), so pass them as const. Unfortunately C lacks any kind of deep
const thingy, so this can't catch all abuses. But at least it acts as a
hint to the reader telling them not to mess about with the state(s).

v2: Update intel_tv_mode_find() and ironlake_edp_pll_on() as well
v3: Deal with intel_sdvo_connector_state
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-9-ville.syrjala@linux.intel.com

The PSR enable/disable need to know things about the crtc state, so
plumb it through. This will become even more important when we start
to reuse the generic infoframe code for the VSC DIP programming as the
infoframe code wants the crtc state as well.

v2: Fix kernel docs
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-7-ville.syrjala@linux.intel.com

DP ports may want to use the video DIP for SDP transmission, so let's
initialize the vfuncs for DP encoders as well. The only exception is
port A eDP prior to HSW as that one doesn't have a video DIP instance.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-6-ville.syrjala@linux.intel.com

Expose across driver for future work. No functional changes.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: NJim Bride <jim.bride@linux.intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818093020.19160-2-jani.nikula@intel.com

Emphasize that this is based on the port, not intel_dp. This is also in
line with the underlying intel_bios_is_port_edp() function. No
functional changes.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: NJim Bride <jim.bride@linux.intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818093020.19160-1-jani.nikula@intel.com