Some high speed mass storage devices fail to enumerate with following
error:

Cannot enable port %i.  Maybe the USB cable is bad?

This happens only when the device is plugged while the controller
is in hibernation state. After exiting hibernation, the controller
detects the device as a low speed device and fail to enumerate it.

Problem occurs only if HPRT0.PWR bit is programmed in a too short
delay after exiting hibernation. Dumping hprt register in
_dwc2_hcd_resume() directly after dwc2_exit_hibernation() shows that
HPRT0.LNSTS (D+/D- level) becomes valid approximately 2ms after
exiting hibernation.

Since dwc2_exit_hibernation() is called from atomic context, move the
delay out of this function.

Delay value is experimental and not mentioned in Synopsys
documentation. To be on the safe side 3ms delay is used.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Disable host interrupts before synchronising dwc2 irq.
So that interrupts are not generated once controller is stopped.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case controller is asked to stop while devices are connected,
disconnect all devices and clean up before stopping.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Port can be resumed in bus_resume callback.
In this case, there is no need to drive resume a second time
when hcd ask for it.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During hcd initialization, hardware accessible flag and lx_state must
be reset to the working state since controller is powered at this stage.

Same logic applied for stop callback.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Disable controller power and enter hibernation when usb bus is
suspended. A phy driver is required to disable the power of the
controller and detect remote-wakeup or disconnection since the
controller will not be able to detect these in this state.

Once the phy driver detects bus activity, it must call
usb_hcd_resume_root_hub.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

lx_state must be used to reflect controller power state only and not
bus state. Thus add a flag to track state during bus suspend.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

port resume sequence may be used in different places. Create a
function to handle it. Make hprt0 read-modify-write atomic and
clear HPRT0_SUSP for both writes as it is a "read, write-set,
and self-clear (R_WS_SC)" bit. Since the lock is released
between the writes, read hprt0 again.

Since the phy clock is stopped in dwc2_port_suspend(), enable it
here and remove the PCGCTL write from dwc2_hcd_hub_control()
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.

This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.

The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h

Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NVincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To avoid sleep while atomic bugs, allocate qtd before calling
dwc2_hcd_urb_enqueue. No need to pass mem_flags to
dwc2_hcd_urb_enqueue any more as no memory allocations are done in it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To avoid sleep while atomic bugs, allocate qh before calling
dwc2_hcd_urb_enqueue. qh pointer can be used directly now instead of
passing ep->hcpriv as double pointer.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit db62b9a8 (usb: dwc2: host: don't
use dma_alloc_coherent with irqs disabled)
introduced a build warning by using NULL
as an integer. Fix that by just using 0 instead
of NULL.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As dwc2 pci module is now exporting dwc2 platform device, include
platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration
option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko.
dwc2.ko is the new platform driver.

Remove all EXPORT_SYMBOL_GPL as they are not needed any more.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for SetPortFeature(PORT_TEST) for root port.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NJingwu Lin <jingwu.lin@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Align buffer must be allocated using kmalloc since irqs are disabled.
Coherency is handled through dma_map_single which can be used with irqs
disabled.
Reviewed-by: NJulius Werner <jwerner@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During urb_enqueue, if the urb can't be queued to the endpoint,
the urb is freed without any spinlock protection.
This leads to memory corruption when concurrent urb_dequeue try to free
same urb->hcpriv.
Thus, ensure the whole urb_enqueue in spinlocked.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Update controller state to indicate suspend entry.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If phy driver is present register hcd handle to it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

msleep(USB_RESUME_TIMEOUT) must be done when the controller drives
the resume. This is true after HPRT0_RES is written.
Moreover, restore the delay after controller power is up.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure we're using the new macro, so our
resume signaling will always pass certification.

Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value  is #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the HCD is disconnected, the DMA transfers still in-flight were cleaned-up
but the count of available DMA channels (e.g. available_host_channels) was not
reset.
The pool of DMA channels can be depleted when doing unclean
disconnection of USB peripherals, and reaches the point where no
transfer was possible until the next reboot/reload of the driver.

Tested by putting a programmable USB mux on the port and randomly
plugging/unpluging a USB HUB with USB mass-storage key, USB-audio and
USB-ethernet dongle connected to its downstream ports, and also doing the
disconnection early while the devices are still enumerating to get more URBs
in-flight.
After the patch, the devices are still enumerating after thousands of cycles,
while the port was totally dead before.
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When a remote wakeup happens during bus_suspend, hcd needs to resume
its root hub.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number  to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix  using the  bare number  to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This reverts commit 0cf884e8.
Even after applying the follow-on patch at
https://patchwork.kernel.org/patch/5325111
there are still problems with device connect on the Altera SOCFPGA
platform at least. One possible fix would be to add a whitelist
to enable suspend/resume on platforms where it does work correctly.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since platform.c will get built for both Host and Gadget, if we leave the
usb_disabled() call in platform.c, it results in the following build error
when (!USB && USB_GADGET) condition is met.

ERROR: "usb_disabled" [drivers/usb/dwc2/dwc2_platform.ko] undefined!

Since usb_disabled() is mostly used to disable USB host functionality, move
the call the host portion for the DWC2 driver.
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Initialize the USB driver to peripheral mode when a B-Device connector
is attached.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c

Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().

Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.

We also move suspend/resume code to common platform code.

Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Hcd controller needs bus_suspend/resume, dwc2 controller make
root hub generate suspend/resume signal with hprt0 register
when work in host mode.
After the root hub enter suspend, we can make controller enter
low power state with PCGCTL register.

We also update the lx_state for hsotg state.

This patch has tested on rk3288 with suspend/resume.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The driver's handling of DMA buffers for non-aligned transfers
was kind of nuts. For IN transfers, it left the URB DMA buffer
mapped until the transfer completed, then synced it, copied the
data from the bounce buffer, then synced it again.

Instead of that, just call usb_hcd_unmap_urb_for_dma() to unmap
the buffer before starting the transfer. Then no syncing is
required when doing the copy. This should also allow handling of
other types of mappings besides just dma_map_single() ones.

Also reduce the size of the bounce buffer allocation for Isoc
endpoints to 3K, since that's the largest possible transfer size.

Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.

The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.

Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: NAndre Heider <a.heider@gmail.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The DWC2 driver should now be in good enough shape to move out of
staging. I have stress tested it overnight on RPI running mass
storage and Ethernet transfers in parallel, and for several days
on our proprietary PCI-based platform.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).

Pass compile test with below commands:
	make O=outout/all allmodconfig
	make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

I fell over the problem reported in
https://github.com/raspberrypi/linux/pull/390:

"Issuing low-speed packets when the root port is in full-speed mode
 causes the root port to stop responding. Explicitly fail when
 enqueuing URBs to a LS endpoint on a FS bus."

with my dwc2 testing in NetBSD, so I adapted the change to dwc2.
Signed-off-by: NNick Hudson <skrll@netbsd.org>
[paulz: fixed up the patch to compile under Linux, and tested it]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed a coding style issue, specifically:

Line 1798: Removed parentheses since return is not a function.
Signed-off-by: NAldo Iljazi <mail@aldo.io>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix some functions called by dwc2_hcd_qtd_add() to return either
a proper error code or 0, instead of somewhat random values.
Then change the caller of dwc2_hcd_qtd_add() to just check the
return value for 0.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>