Also correct indentation in net/wireless/reg.c.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't need "sdata" any more after:
	d84f3234
	mac80211: remove dev_hold/put calls
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware  if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.

For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.

Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.

An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.

The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch is based on a RFC patch by Kalle Valo.

The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.

Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.

Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a wireless.h macro for this, might as well use it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a wireless.h macro for this, might as well use it.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch renames the (never officially released) sysfs-knobs
"blocked_hw" and "blocked_sw" to "hard" and "soft", as the hardware vs
software conotation is misleading.

It also gets rid of not needed locks around u32-read-access.
Signed-off-by: NFlorian Mickler <florian@mickler.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.

the section of the ibss code which deals with updating supported rates for
an already existing station failed to inform the rate control module about the
new rates. as both minstrel and pid don't have an update function i just use
the init function.

also remove unnecessary (unsigned long long) casts and edit debug message.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I accidentally merged an incomplete version of the patch...

This reverts commit b4d59a93.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a cooked monitor interface is active, ieee80211_tx_status()
generates a radiotap header for every single frame, even if it wasn't
injected and thus won't be sent to a monitor interface.
This patch reduces cpu utilization by moving the cooked monitor check a
bit earlier, before it generates the rtap header.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes it possible to reuse the minstrel rate control ops
from another rate control module. This is useful in preparing for the
new 802.11n implementation of minstrel, which will reuse the old code
for legacy stations.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up the debugfs read function for the statistics by
using simple_read_from_buffer instead of its own semi-broken hack.
Also removes a useless member of the minstrel debugfs info struct.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I discovered that if EMBEDDED=y, one can accidentally build a mac80211 stack
and drivers w/ no rate control algorithm.  For drivers like RTL8187 that don't
supply their own RC algorithms, this will cause ieee80211_register_hw to
fail (making the driver unusable).

This will tell kconfig to provide a warning if no rate control algorithms
have been selected.  That'll at least warn the user; users that know that
their drivers supply a rate control algorithm can safely ignore the
warning, and those who don't know (or who expect to be using multiple
drivers) can select a default RC algorithm.
Signed-off-by: NAndres Salomon <dilinger@collabora.co.uk>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This commit introduces two new sysfs knobs.

/sys/class/rfkill/rfkill[0-9]+/blocked_hw: (ro)
	hardblock kill state
/sys/class/rfkill/rfkill[0-9]+/blocked_sw: (rw)
	softblock kill state
Signed-off-by: NFlorian Mickler <florian@mickler.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers can now advertise to cfg80211 that they have
multiple MAC addresses reserved for a device, but we
don't currently make use of that in mac80211.

Change that and assign different addresses to new
virtual interfaces (if addresses are available) in
order to make it easier for users to use multiple
virtual interfaces; they no longer need to always
assign a new MAC address manually.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current software scan implemenation in mac80211 returns to the operating
channel after each scanned channel. However, in some situations (e.g. no
traffic) it would be nicer to scan a few channels in a row to speed up
the scan itself.

Hence, after scanning a channel, check if we have queued up any tx frames and
return to the operating channel in that case.

Unfortunately we don't know if the AP has buffered any frames for us. Hence,
scan only as many channels in a row as the pm_qos latency and the negotiated
listen interval allows us to.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.

also the section of the ibss code which deals with updating supported rates for
an already existing station fails to inform the rate control module about the
new rates. as i don't know how to fix this (minstrel does not have an update
function), i have just added a comment for now.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The noise value as is won't be used, isn't
filled by most drivers and doesn't really
make a whole lot of sense on a per packet
basis -- proper cfg80211 survey support in
mac80211 will need to be different.

Mark the struct member as deprecated so it
will be removed from drivers.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.

This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.

Fix this by passing the new channel type to the driver.

Cc: stable@kernel.org
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.

This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: NJouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following build error when IGMP_SNOOPING is not enabled.
In file included from net/bridge/br.c:24:
net/bridge/br_private.h: In function 'br_multicast_is_router':
net/bridge/br_private.h:361: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:362: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:363: error: 'struct net_bridge' has no member named 'multicast_router_timer'
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use scm_send and scm_recv on both unix domain and
netlink sockets, but only unix domain sockets support
everything required for file descriptor passing,
so error if someone attempts to pass file descriptors
over netlink sockets.

Cc: stable@kernel.org
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_NTUPLE flag setting introduced a bug:  non-ntuple flags
like LRO may be successfully set, before ioctl(2) returns failure
to userspace.

The set-flags operation should be all-or-none, rather than leaving
things in an inconsistent state prior to reporting failure to
userspace.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Inode field in /proc/net/{tcp,udp,packet,raw,...} is useful to know the types of
file descriptors associated to a process. Actually lsof utility uses the field.
Unfortunately, unlike /proc/net/{tcp,udp,packet,raw,...}, /proc/net/netlink doesn't have the field.
This patch adds the field to /proc/net/netlink.
Signed-off-by: NMasatake YAMATO <yamato@redhat.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the user to the IGMP parameters related to the
snooping function of the bridge.  This includes various time
values and retransmission limits.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the user to control the hash elasticity/max
parameters.  The elasticity setting does not take effect until
the next new multicast group is added.  At which point it is
checked and if after rehashing it still can't be satisfied then
snooping will be disabled.

The max setting on the other hand takes effect immediately.  It
must be a power of two and cannot be set to a value less than the
current number of multicast group entries.  This is the only way
to shrink the multicast hash.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the user to disable IGMP snooping completely
through a sysfs toggle.  It also allows the user to reenable
snooping when it has been automatically disabled due to hash
collisions.  If the collisions have not been resolved however
the system will refuse to reenable snooping.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the user to forcibly enable/disable ports as
having multicast routers attached.  A port with a multicast router
will receive all multicast traffic.

The value 0 disables it completely.  The default is 1 which lets
the system automatically detect the presence of routers (currently
this is limited to picking up queries), and 2 means that the port
will always receive all multicast traffic.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch finally hooks up the multicast snooping module to the
data path.  In particular, all multicast packets passing through
the bridge are fed into the module and switched by it.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch hooks up the bridge start/stop and add/delete/disable
port functions to the new multicast module.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to perform selective multicast forwarding.

We forward multicast traffic to a set of ports plus all multicast
router ports.  In order to avoid duplications among these two
sets of ports, we order all ports by the numeric value of their
pointers.  The two lists are then walked in lock-step to eliminate
duplicates.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the core functionality of IGMP snooping support
without actually hooking it up.  So this patch should be a no-op
as far as the bridge's external behaviour is concerned.

All the new code and data is controlled by the Kconfig option
BRIDGE_IGMP_SNOOPING.  A run-time toggle is also available.

The multicast switching is done using an hash table that is
lockless on the read-side through RCU.  On the write-side the
new multicast_lock is used for all operations.  The hash table
supports dynamic growth/rehashing.

The hash table will be rehashed if any chain length exceeds a
preset limit.  If rehashing does not reduce the maximum chain
length then snooping will be disabled.

These features may be added in future (in no particular order):

* IGMPv3 source support
* Non-querier router detection
* IPv6
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the main loop body in br_flood into the function
may_deliver.  The code that clones an skb and delivers it is moved
into the deliver_clone function.

This allows this to be reused by the future multicast forward
function.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch makes BR_INPUT_SKB_CB available on the xmit path so
that we could avoid passing the br pointer around for the purpose
of collecting device statistics.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the packet is delivered to the local bridge device we may
end up cloning it unnecessarily if no bridge port can receive
the packet in br_flood.

This patch avoids this by moving the skb_clone into br_flood.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows tail-call on the call to br_pass_frame_up
in br_handle_frame_finish.  This is now possible because of the
previous patch to call br_pass_frame_up last.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the moment we deliver to the local bridge port via the function
br_pass_frame_up before all other ports.  There is no requirement
for this.

For the purpose of IGMP snooping, it would be more convenient if
we did the local port last.  Therefore this patch rearranges the
bridge input processing so that the local bridge port gets to see
the packet last (if at all).
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>