The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.

The chip is controlled through the I2C bus.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Fix recent fusion driver kernel-doc fatal error and warnings.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Eric.Moore@lsi.com
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.  This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.
Reported-by: NYinghai Lu <yhlu.kernel@gmail.com>
Tested-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

New revision of Atmel MCI interface adds new features. This is a update of
register definition in header file. This new MCI IP is called MCI2.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The MCI IP is shared among AVR32 and AT91 SOCs.
AT91 has specific bit definitions in the user interface of MCI SD/MMC IP.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <spyro@f2s.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.

Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.

[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

If using ADMA, then we should print the ADMA error
and current pointer in sdhci_dumpregs() when any
debug is requested.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This patch fixes the clock setup in tmio_mmc.

  * Incorrect divider setting
  * Cruft written to the clock registers (seemingly harmless but Not
Good (tm))

It also eliminates some unnecessary ifs and tidies the loop syntax.

Thanks to Philipp Zabel who discovered the divider issue, commenting

   "Except for the SDCLK = HCLK (divider bypassed) case, the clock
    setting resulted in double the requested frequency.
    The smallest possible frequency (f_max/512) is configured with
    a divider setting 0x80, not 0x40."
Signed-off-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

ASIC3 can disable the memory, so we need to wait for mfd_cell->enable
to enable the memory before we can map the SD control registers.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Use an IRQF_TRIGGER_ flag in request_irq instead.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Acked-by: NSamuel Ortiz <sameo@openedhand.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Added a platform driver which uses the SDHCI core.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.

As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text.  This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.

This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: NJorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

 drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
 drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
 drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
 make[1]: *** [drivers/net/cnic.o] Error 1
 make: *** [drivers/net/cnic.o] Error 2

Caused by not including linux/module.h
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Fix cnic build for case of CONFIG_INET=n.
Fix cnic build for case of CONFIG_IPV6=m and CONFIG_CNIC=y.

Fixes these build errors:

cnic.c:(.text+0x236a1d): undefined reference to `ip_route_output_key'
cnic.c:(.text+0x15a8e8): undefined reference to `ip6_route_output'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There is sometimes a need for the ocores driver to add devices to the
bus when installed.

i2c_register_board_info can not always be used, because the I2C devices
 are not known at an early state, they could for instance be connected
 on a I2C bus on a PCI device which has the Open Cores IP.

i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.

The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code

Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:

s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.

OMAP3430 TRM gives the following equations:

	F/S: tLow  = (scll + 7) * internal_clk
	     tHigh = (sclh + 5) * internal_clk
	HS:  tLow  = (scll + 7) * fclk
	     tHigh = (sclh + 5) * fclk

Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):

	speed	tLow		tHigh
	3400	160 ns		60 ns
	1700	320 ns		120 ns

and for F/S:

	speed	tLow		tHigh
	400	1300 ns		600 ns
	100	4700 ns		4000 ns

By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.

Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.

It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: NFrank Shew <fshew@geometrics.com>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make sure we don't end up with an invalid CLKDIV=0 in case someone
specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100).
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shortened subject line]
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch reworks the platform driver code for legacy
suspend and resume to avoid installing callbacks in
struct device_driver. A warning is also added telling
users to update the platform driver to use dev_pm_ops.

The functions platform_legacy_suspend()/resume() directly
call suspend and resume callbacks in struct platform_driver
instead of wrapping things in platform_drv_suspend()/resume().
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>