One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.

So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.

v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
    so we were disabling interrupts.
    Credits-to: Clinton
    Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
    and clock on in 2 separated reg writes. (Paulo)
    Also update bits definitions to use space
    (1 << 1) instead of (1<<1). (Paulo)

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NKahola, Mika <mika.kahola@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com

All the low level cdclk bits are present, so let's add the required
hooks to reconfigure cdclk on the fly.

Cannonlake also needs to adjust the minimal pixel rate
as gen9 platforms. Specially for the Azalia audio case.

v2: Rebase due to cnl_sanitize_cdclk()
v3: Rebased by Rodrigo on top of Ville's cdclk rework.
v4: Rebase moving cnl_calc_cdclk up to follow same order
    as previous platforms.
v2: Squash drm/i915/cnl: Adjust min pixel rate. to address
    the current limitation where CDCLK cannot be set to 168MHz
    if audio is used with 96MHz. (Imre)
v3: adjust some of the clock limits within
    bdw_adjust_min_pipe_pixel_rate. (Ville/DK/Imre).
    Fix commit message messed by squash.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-4-git-send-email-rodrigo.vivi@intel.com

Implement the CNL display init/uninit sequence as outlined in Bspec.

Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.

v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
    bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
    Fix procpon Mask. (Credits-to Paulo and Clint)
    Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
    (Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
    Remove unused DW8 and an extra blank line. (all noticed
    by Imre).
v9: Remove __attribute__((unused)) added on latest version
    of drm/i915/cnl: Implement .set_cdclk() for CNL.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com

Add support for changing the cdclk frequency on CNL. Again, quite
similar to BXT, but there are some annoying differences which means
trying to share more code might not be feasible:
* PLL ratio now lives in the PLL enable register
* pcode came from SKL, not from BXT

We support three cdclk frequencies: 168,336,528 Mhz. The first two
use the same PLL frequency, the last one uses a different one meaning
we once again may need to toggle the PLL off and on when changing
cdclk.

v2: Rebased by Rodrigo on top of Ville's cdclk rework.
v3: Respect order of set_ bellow get_ (Ville)
v4: Added __attribute__((unused)) to avoid broken compilation with Werror.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-2-git-send-email-rodrigo.vivi@intel.com

Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported

v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com

Pass crtc_state to the enable callback, and connector_state to all callbacks.
This will eliminate the need to guess for the correct pipe in these
callbacks.

The crtc state is required for pch_enable_backlight to obtain the correct
cpu_transcoder.

intel_dp_aux_backlight's setup function is called before hw readout, so
crtc_state and connector_state->best_encoder are NULL in the enable()
and set() callbacks.

This fixes the following series of warns from intel_get_pipe_from_connector:
[  219.968428] ------------[ cut here ]------------
[  219.968481] WARNING: CPU: 3 PID: 2457 at
drivers/gpu/drm/i915/intel_display.c:13881
intel_get_pipe_from_connector+0x62/0x90 [i915]
[  219.968483]
WARN_ON(!drm_modeset_is_locked(&dev->mode_config.connection_mutex))
[  219.968485] Modules linked in: nls_iso8859_1 snd_hda_codec_hdmi
snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec
snd_hda_core snd_hwdep snd_pcm intel_rapl x86_pkg_temp_thermal coretemp
kvm_intel snd_seq_midi snd_seq_midi_event kvm snd_rawmidi irqbypass
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc snd_seq
snd_seq_device serio_raw snd_timer aesni_intel aes_x86_64 crypto_simd
glue_helper cryptd lpc_ich snd mei_me shpchp soundcore mei rfkill_gpio
mac_hid intel_pmc_ipc parport_pc ppdev lp parport ip_tables x_tables
autofs4 hid_generic usbhid igb ahci i915 xhci_pci dca xhci_hcd ptp
sdhci_pci sdhci libahci pps_core i2c_hid hid video
[  219.968573] CPU: 3 PID: 2457 Comm: kworker/u8:3 Tainted: G        W
4.10.0-tip-201703010159+ #2
[  219.968575] Hardware name: Intel Corp. Broxton P/NOTEBOOK, BIOS
APLKRVPA.X64.0144.B10.1606270006 06/27/2016
[  219.968627] Workqueue: events_unbound intel_atomic_commit_work [i915]
[  219.968629] Call Trace:
[  219.968640]  dump_stack+0x63/0x87
[  219.968646]  __warn+0xd1/0xf0
[  219.968651]  warn_slowpath_fmt+0x4f/0x60
[  219.968657]  ? drm_printk+0x97/0xa0
[  219.968708]  intel_get_pipe_from_connector+0x62/0x90 [i915]
[  219.968756]  intel_panel_enable_backlight+0x19/0xf0 [i915]
[  219.968804]  intel_edp_backlight_on.part.22+0x33/0x40 [i915]
[  219.968852]  intel_edp_backlight_on+0x18/0x20 [i915]
[  219.968900]  intel_enable_ddi+0x94/0xc0 [i915]
[  219.968950]  intel_encoders_enable.isra.93+0x77/0x90 [i915]
[  219.969000]  haswell_crtc_enable+0x310/0x7f0 [i915]
[  219.969051]  intel_update_crtc+0x58/0x100 [i915]
[  219.969101]  skl_update_crtcs+0x218/0x240 [i915]
[  219.969153]  intel_atomic_commit_tail+0x350/0x1000 [i915]
[  219.969159]  ? vtime_account_idle+0xe/0x50
[  219.969164]  ? finish_task_switch+0x107/0x250
[  219.969214]  intel_atomic_commit_work+0x12/0x20 [i915]
[  219.969219]  process_one_work+0x153/0x3f0
[  219.969223]  worker_thread+0x12b/0x4b0
[  219.969227]  kthread+0x101/0x140
[  219.969230]  ? rescuer_thread+0x340/0x340
[  219.969233]  ? kthread_park+0x90/0x90
[  219.969237]  ? do_syscall_64+0x6e/0x180
[  219.969243]  ret_from_fork+0x2c/0x40
[  219.969246] ---[ end trace 0a8fa19387b9ad6d ]---

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100022Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170612102115.23665-4-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Passing the state is also needed to convert the backlight functions
to use the correct state instead of looking it up.

This is done as a separate commit to allow easier bisecting.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100022Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170612102115.23665-3-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

The backlight functions need to determine the pipe and the transcoder the
backlight will be enabled on, so pass crtc_state instead of trying to
dereference the state without holding locks.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100022Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170612102115.23665-2-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Current it's strictly checked if PVINFO version matches 1.0
for GVT-g i915 guest which doesn't help for compatibility at
all and forces GVT-g host can't extend PVINFO easily with version
bump for real compatibility check.

This fixes that to check minimal required PVINFO version instead.

v2:
- drop unneeded version macro
- use only major version for sanity check

v3:
- fix up PVInfo value with kernel type
- one indent fix
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170609074805.5101-1-zhenyuw@linux.intel.com

both platforms. We haven't recieved any separated release
specifically for Coffee Lake so let's just re-use what
is already there for Kabylake.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497038550-30910-1-git-send-email-rodrigo.vivi@intel.com

Coffee Lake reuses Kabylake's HUC firmware.

v2: Change Coffeelake to Coffee Lake

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NLukasz Fiedorowicz <lukasz.fiedorowicz@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965704-23610-2-git-send-email-anusha.srivatsa@intel.com

Coffee Lake reuses Kabylake's GuC.

v2: Change Coffeelake to Coffee Lake

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NLukasz Fiedorowicz <lukasz.fiedorowicz@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965704-23610-1-git-send-email-anusha.srivatsa@intel.com

Add PCI Ids for U Skus of Coffeelake.

v2: Use intel_coffeelake_gt3_info, in accordance to-
Rodrigo's patch:

v3: rebased

v3: Remove unused INTEL_CFL_IDS(Rodrigo).

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965267-21725-3-git-send-email-anusha.srivatsa@intel.com

Add PCI Ids for H Sku by following the BSpec.

v2: Remove unused INTEL_CFL_IDS.(Rodrigo).
v3: Add missing IDs(Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965267-21725-2-git-send-email-anusha.srivatsa@intel.com

Add PCI Ids for S Sku following the BSpec.

v2: Remove the unused INTEL_CFL_IDS.(Rodrigo)
v3: Add missing IDs(Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496965267-21725-1-git-send-email-anusha.srivatsa@intel.com

Geminilake is now included in CI, making it part of the pre-merge
criteria. The support should be in good enough shape, so let's remove
the alpha_support flag.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608114800.17201-1-ander.conselvan.de.oliveira@intel.com

The whole Display engine for Coffee Lake is pretty much
identical to the Kabylake. For this reason let's reuse
all display related production workardounds here even though
CFL is not explicit listed at Display workarounds page at Spec.

v2: moved intel_pm.c chunck to this patch in order to address
    all display related w/a in a single place.

Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-3-git-send-email-rodrigo.vivi@intel.com

So let's force it on the virtual detection.

Also it is still the only silicon for now on this PCH,
so WARN otherwise.

v2: Rebased on top of Cannonlake and added the missed
    debug message as pointed by DK.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-2-git-send-email-rodrigo.vivi@intel.com

Coffee Lake is a Intel® Processor containing Intel® HD Graphics
following Kabylake.

It is Gen9 graphics based platform on top of CNP PCH.

Let's start by adding the platform definition based on previous
platforms but yet as preliminary_hw_support.

On following patches we will start adding PCI IDs and the
platform specific changes.

v2: Also add BS2 ring that is present on GT3. As on KBL, according
    spec: "GT3 also has additional media blocks with second instance
    of VEBox and VDBox each", i.e. BSD2 ring in our case. Noticed
    when reviewing PCI ID patches.

v3: CFL_PLATFORM instead for CFL_FEATURES because it contains
    Platform information and no new features when compared to
    BDW_FEATURES definition.

v4: Rebased on top of Cannonlake patches.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-1-git-send-email-rodrigo.vivi@intel.com

Originally we would enable and disable the breadcrumb interrupt
immediately on demand. This was slow enough to have a large impact
(>30%) on tasks that hopped between engines. However, by using a shadow
to keep the irq alive for an extra interrupt (see commit 67b807a8
("drm/i915: Delay disabling the user interrupt for breadcrumbs")) and
by recently reducing the cost in adding ourselves to the signal tree, we
no longer need to spin-request during await_request to avoid delays in
throughput tests. Without the earlier patches to stop the wakeup when
signaling if the irq was already active, we saw no improvement in
execbuf overhead (and corresponding contention in other clients) despite
the removal of the spinner in a simple test like glxgears. This means
there will be scenarios where now we spend longer enabling the interrupt
than we would have spent spinning, but these are not likely to have as
noticeable an impact as the high frequency test cases (where there
should not be any regression).

Ulterior motive: generalising the engine->sync_to to handle different
types of semaphores and non-semaphores.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-4-chris@chris-wilson.co.uk

Enabling the interrupt for the signaler takes a finite amount of time (a
few microseconds) during which it is possible for the request to
complete. Check afterwards and skip adding the request to the signal
rbtree if it complete.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-3-chris@chris-wilson.co.uk

The important condition that we need to check after enabling the
interrupt for signaling is whether the request completed in the process
(and so we missed that interrupt). A large cost in enabling the
signaling (rather than waiters) is in waking up the auxiliary signaling
thread, but we only need to do so to catch that missed interrupt. If we
know we didn't miss any interrupts (because we didn't arm the interrupt)
then we can skip waking the auxiliary thread.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-2-chris@chris-wilson.co.uk

Setting up the irq to signal the request completion takes a finite
amount of time, during which it is possible that the request already
completed. Check afterwards, just in case, so that we can respond
immediately.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-1-chris@chris-wilson.co.uk

And prevent calling i915_ggtt_disable_guc twice (the first when GuC init
failed, and the second time during driver unload / intel_uc_fini_hw),
and hitting the GEM_BUG_ON.

v2: Clear enable_guc_loading unconditionally (Michal)
    Make sure guc_free_load_err_log is still called (Daniele)
    Don't shoot the messenger (Chris)

Fixes: 3950bf3d ("drm/i915/guc: Add onion teardown to the GuC
setup")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170605171251.9905-1-michel.thierry@intel.com

Replace the large comment about requiring the powerwell for
intel_uncore_arm_unclaimed_mmio_detection() by moving the arming of the
mmio error detection into the powerwell held for modesetting. Thereby
also accomplishing the goal of only arming the mmio detection after a
full modeset.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504115508.13571-1-chris@chris-wilson.co.ukReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This patch clean up a bit the platform definition block in
a way to avoid duplications and to let clear that GT3 for
the current platform only have the extra Media engine (BSD2).

v2: Kabylake IS_KABYLAKE as Anusha noticed.

v3: Avoid EXTRA_ENGINE_MASK and list rings out on GT3 to
    make it more clear.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496765166-7068-1-git-send-email-rodrigo.vivi@intel.com

Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com

The workaround added in
commit c6782b76 ("drm/i915/gen9: Reset secondary power well
equests left on by DMC/KVMR")
needs to be applied on Cannonlake as well.

So let's assume any platform using this power well setup
will also need and let's just go ahead and remove if condition.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-11-git-send-email-rodrigo.vivi@intel.com

CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.

Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.

v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
    for the same reasons as v4 when we found out that current CNL
    SKUs don't have the full port E split.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com

Indirect Context Offset Pointer has changed for Cannonlake.

INDIRECT_CTX_OFFSET[15:6] valid value for CNL is 19h per Spec.

v2: rebased to intel_lr_indirect_ctx_offset

v3: Commit message added per Tvrtko request.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-9-git-send-email-rodrigo.vivi@intel.com

All registers and default configuration are the same for Skylake
and Cannonlake.

v2: Don't apply Wa for platforms without MOCS. (Paulo)

v3: Removed WaDisableSkipCaching that Joonas noticed that
according to spec it is not applicable to CNL.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-8-git-send-email-rodrigo.vivi@intel.com

Cannonlake also supports slice power gating on devices with more
than one slice as SKL. Let's assume that this is the same for SKL+
and exclude BXT only.

v2: Also remove KBL.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-7-git-send-email-rodrigo.vivi@intel.com

Issue: VIZ-4525
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJames Irwin <james.irwin@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-6-git-send-email-rodrigo.vivi@intel.com

We're going to use it in the next commits.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-5-git-send-email-rodrigo.vivi@intel.com

By the Spec all CNL Y skus are 2+2, i.e. GT2.

v2: Really include the PCI IDs to the picidlist[];
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-4-git-send-email-rodrigo.vivi@intel.com

Platform enabling and its power-on are organized in different
skus (U x Y x S x H, etc). So instead of organizing it in
GT1 x GT2 x GT3 let's also use the platform sku.

This is also the new Spec style what makes the review much
more easy and straightforward.

v2: Really include the PCI IDs to the picidlist[];
v3: Remove PCI IDs not present in spec.
v4: Rebase.
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NClinton Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-3-git-send-email-rodrigo.vivi@intel.com

Avoid warning when CNP is detected with CNL.

Also let's force it on the virtual detection.
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-2-git-send-email-rodrigo.vivi@intel.com

Cannonlake is a Intel® Processor containing Intel® HD Graphics
following Kabylake.

It is Gen10.

Let's start by adding the platform definition based on previous
platforms but yet as alpha_support.

On following patches we will start adding PCI IDs and the
platform specific changes.

CNL has an increased DDB size as Damien had previously
noticed and provided a separated patch that got squashed here.

v2: Squash DDB size here per Ander request.

Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-1-git-send-email-rodrigo.vivi@intel.com

The clipped src coordinates have already been rotated by 270 degrees for
when the plane rotation is 90/270 degrees, hence the FBC code should no
longer swap the width and height.

Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-4-ville.syrjala@linux.intel.comReviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

skl_check_plane_surface() already rotates the clipped plane source
coordinates to match the scanout direction because that's the way
the GTT mapping is set up. Thus we no longer need to rotate the
coordinates in the watermark code.

For cursors we use the non-clipped coordinates which are not rotated
appropriately, but that doesn't actually matter since cursors don't
even support 90/270 degree rotation.

v2: Resolve conflicts from SKL+ wm rework

Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6 ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-3-ville.syrjala@linux.intel.comTested-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>