Florian Fainelli says:

====================
net: Implenent ethtool::nway_reset for a few drivers

This patch series depends on "net: phy: Centralize auto-negotation restart"
since it provides phy_ethtool_nway_reset as a helper function.

The drivers here already support PHYLIB, so there really is no reason why
restarting auto-negotiation would not be possible with these.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Utilize the generic phy_ethtool_nway_reset() helper function to
implement an autonegotiation restart.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: busy-poll: allow preemption and other optimizations

It is time to have preemption points in sk_busy_loop() and improve
its scalability.

Also napi_complete() and friends can tell drivers when it is safe to
not re-enable device interrupts, saving some overhead under
high busy polling.

mlx4 and bnx2x are changed accordingly, to show how this busy polling
status can be exploited by drivers.

Next steps will implement Zach Brown suggestion, where NAPI polling
would be enabled all the time for some chosen queues.
This is needed for efficient epoll() support anyway.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch from napi_complete() to napi_complete_done()
for better GRO support (gro_flush_timeout) and core NAPI
features.

Do not rearm interrupts if we are busy polling,
to reduce bus and interrupts overhead.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not rearm interrupts if we are busy polling.

mlx4 uses separate CQ for TX and RX, so number of TX interrupts
does not change, unfortunately.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NAPI drivers use napi_complete_done() or napi_complete() when
they drained RX ring and right before re-enabling device interrupts.

In busy polling, we can avoid interrupts being delivered since
we are polling RX ring in a controlled loop.

Drivers can chose to use napi_complete_done() return value
to reduce interrupts overhead while busy polling is active.

This is optional, legacy drivers should work fine even
if not updated.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now sk_busy_loop() can schedule by itself, we can remove
need_resched() check from sk_can_busy_loop()

Also add a const to its struct sock parameter.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 4cd13c21 ("softirq: Let ksoftirqd do its job"),
sk_busy_loop() needs a bit of care :
softirqs might be delayed since we do not allow preemption yet.

This patch adds preemptiom points in sk_busy_loop(),
and makes sure no unnecessary cache line dirtying
or atomic operations are done while looping.

A new flag is added into napi->state : NAPI_STATE_IN_BUSY_POLL

This prevents napi_complete_done() from clearing NAPIF_STATE_SCHED,
so that sk_busy_loop() does not have to grab it again.

Similarly, netpoll_poll_lock() is done one time.

This gives about 10 to 20 % improvement in various busy polling
tests, especially when many threads are busy polling in
configurations with large number of NIC queues.

This should allow experimenting with bigger delays without
hurting overall latencies.

Tested:
 On a 40Gb mlx4 NIC, 32 RX/TX queues.

 echo 70 >/proc/sys/net/core/busy_read
 for i in `seq 1 40`; do echo -n $i: ; ./super_netperf $i -H lpaa24 -t UDP_RR -- -N -n; done

    Before:      After:
 1:   90072   92819
 2:  157289  184007
 3:  235772  213504
 4:  344074  357513
 5:  394755  458267
 6:  461151  487819
 7:  549116  625963
 8:  544423  716219
 9:  720460  738446
10:  794686  837612
11:  915998  923960
12:  937507  925107
13: 1019677  971506
14: 1046831 1113650
15: 1114154 1148902
16: 1105221 1179263
17: 1266552 1299585
18: 1258454 1383817
19: 1341453 1312194
20: 1363557 1488487
21: 1387979 1501004
22: 1417552 1601683
23: 1550049 1642002
24: 1568876 1601915
25: 1560239 1683607
26: 1640207 1745211
27: 1706540 1723574
28: 1638518 1722036
29: 1734309 1757447
30: 1782007 1855436
31: 1724806 1888539
32: 1717716 1944297
33: 1778716 1869118
34: 1805738 1983466
35: 1815694 2020758
36: 1893059 2035632
37: 1843406 2034653
38: 1888830 2086580
39: 1972827 2143567
40: 1877729 2181851
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc-6.2.1 gives the following warning:
kernel/bpf/bpf_lru_list.c: In function ‘__bpf_lru_list_rotate_inactive.isra.3’:
kernel/bpf/bpf_lru_list.c:201:28: warning: ‘next’ may be used uninitialized in this function [-Wmaybe-uninitialized]

The "next" is currently initialized in the while() loop which must have >=1
iterations.

This patch initializes next to get rid of the compiler warning.

Fixes: 3a08c2fd ("bpf: LRU List")
Reported-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new option CONFIG_IPV6_SEG6_LWTUNNEL to enable/disable
support of encapsulation with the lightweight tunnels. When this option
is enabled, CONFIG_LWTUNNEL is automatically selected.

Fix commit 6c8702c6 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")

Without a proper option to control lwtunnel support for SR-IPv6, if
CONFIG_LWTUNNEL=n then the IPv6 initialization fails as a consequence
of seg6_iptunnel_init() failure with EOPNOTSUPP:

NET: Registered protocol family 10
IPv6: Attempt to unregister permanent protocol 6
IPv6: Attempt to unregister permanent protocol 136
IPv6: Attempt to unregister permanent protocol 17
NET: Unregistered protocol family 10

Tested (compiling, booting, and loading ipv6 module when relevant)
with possible combinations of CONFIG_IPV6={y,m,n},
CONFIG_IPV6_SEG6_LWTUNNEL={y,n} and CONFIG_LWTUNNEL={y,n}.
Reported-by: NLorenzo Colitti <lorenzo@google.com>
Suggested-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tobias Regnery says:

====================
alx: add multi queue support

This patchset lays the groundwork for multi queue support in the alx driver
and enables multi queue support for the tx path by default. The hardware
supports up to 4 tx queues.

Benefits are better utilization of multi core cpus and the usage of the
msi-x support by default which splits the handling of rx / tx and misc
other interrupts.

The rx path is a little bit harder because apparently (based on the limited
information from the downstream driver) the hardware supports up to 8 rss
queues but only has one hardware descriptor ring on the rx side. So the rx
path will be part of another patchset.

Tested on my AR8161 ethernet adapter with different tests:
- there are no regressions observed during my daily usage
- iperf tcp and udp tests shows no performance regressions
- netperf TCP_RR and UDP_RR shows a slight performance increase of about
  1-2% with this patchset applied

This work is based on the downstream driver at github.com/qca/alx

Changes in V2:
	- drop unneeded casts in alx_alloc_rx_ring (Patch 1)
	- add additional information about testing and benefit to the
	  changelog
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable multiple tx queues by default based on the number of online cpus. The
hardware supports up to four tx queues.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the module parameter to enable msi-x support and enable msi-x
interrupts unconditionally by default. This is a preparatory step to enable
multi queue support by default, because this is only working with msi-x
interrupts.
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the tx path to send data on multiple tx queues. It
introduces per queue register adresses and uses them in the alx_tx_queue
structs.

There are new helper functions for the queue mapping in the tx path.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate, initialise and free alx_tx_queue structs based on the number of
alx_napi structures. Also increase the size of the descriptor memory based
on the number of tx queues in use.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the interrupt bringup code and the interrupt handler for msi-x
interrupts in order to handle multiple queues.

We must change the poll function because with multiple queues it is possible
that an alx_napi structure has only a tx or only a rx queue pointer.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the tx and rx queue structures from the alx_priv structure and switch
everything over to the queue pointers in the alx_napi structure.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new functions to allocate and free the alx_napi structures and use them
in __alx_open and __alx_stop. We only allocate one of these structures for
now, as the rest of the driver is not yet ready for multiple queues.

We switch over the setup of the interrupt mask and the call to netif_napi_add
to the new function because we must adjust these later on a per queue basis.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the driver data structures to be able to handle multiple queues.

Based on the downstream driver at github.com/qca/alx
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split the allocation of descriptor memory and the buffer allocation into a
tx and rx function. This is in preparation for multiple queues where we
need to iterate over the new functions.

While at it drop the unneeded casting on the rx side.
Signed-off-by: NTobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Madalin Bucur says:

====================
dpaa_eth: Add the QorIQ DPAA Ethernet driver

This patch series adds the Ethernet driver for the Freescale
QorIQ Data Path Acceleration Architecture (DPAA).

This version includes changes following the feedback received
on previous versions from Eric Dumazet, Bob Cochran, Joe Perches,
Paul Bolle, Joakim Tjernlund, Scott Wood, David Miller - thank you.

Together with the driver a managed version of alloc_percpu
is provided that simplifies the release of per-CPU memory.

The Freescale DPAA architecture consists in a series of hardware
blocks that support the Ethernet connectivity. The Ethernet driver
depends upon the following drivers that are currently in the Linux
kernel:
 - Peripheral Access Memory Unit (PAMU)
    drivers/iommu/fsl_*
 - Frame Manager (FMan) added in v4.4
    drivers/net/ethernet/freescale/fman
 - Queue Manager (QMan), Buffer Manager (BMan) added in v4.9-rc1
    drivers/soc/fsl/qbman

dpaa_eth interfaces mapping to FMan MACs:

  dpaa_eth       /eth0\     ...       /ethN\
  driver        |      |             |      |
  -------------   ----   -----------   ----   -------------
       -Ports  / Tx  Rx \    ...    / Tx  Rx \
  FMan        |          |         |          |
       -MACs  |   MAC0   |         |   MACN   |
             /   dtsec0   \  ...  /   dtsecN   \ (or tgec)
            /              \     /              \(or memac)
  ---------  --------------  ---  --------------  ---------
      FMan, FMan Port, FMan SP, FMan MURAM drivers
  ---------------------------------------------------------
      FMan HW blocks: MURAM, MACs, Ports, SP
  ---------------------------------------------------------

dpaa_eth relation to QMan, FMan:
              ________________________________
  dpaa_eth   /            eth0                \
  driver    /                                  \
  ---------   -^-   -^-   -^-   ---    ---------
  QMan driver / \   / \   / \  \   /  | BMan    |
             |Rx | |Rx | |Tx | |Tx |  | driver  |
  ---------  |Dfl| |Err| |Cnf| |FQs|  |         |
  QMan HW    |FQ | |FQ | |FQ | |   |  |         |
             /   \ /   \ /   \  \ /   |         |
  ---------   ---   ---   ---   -v-    ---------
            |        FMan QMI         |         |
            | FMan HW       FMan BMI  | BMan HW |
              -----------------------   --------

where the acronyms used above (and in the code) are:
DPAA = Data Path Acceleration Architecture
FMan = DPAA Frame Manager
QMan = DPAA Queue Manager
BMan = DPAA Buffers Manager
QMI = QMan interface in FMan
BMI = BMan interface in FMan
FMan SP = FMan Storage Profiles
MURAM = Multi-user RAM in FMan
FQ = QMan Frame Queue
Rx Dfl FQ = default reception FQ
Rx Err FQ = Rx error frames FQ
Tx Cnf FQ = Tx confirmation FQ
Tx FQs = transmission frame queues
dtsec = datapath three speed Ethernet controller (10/100/1000 Mbps)
tgec = ten gigabit Ethernet controller (10 Gbps)
memac = multirate Ethernet MAC (10/100/1000/10000)

Changes from v7:
 - remove the debug option to use a common buffer pool for all the
   interfaces

Changed from v6:
 - fixed an issue on an error path in dpaa_set_mac_address()
 - removed NDO operation definitions that were not needed
 - sorted the local variable declarations
 - cleaned up a few checkpatch checks
 - removed friendly network interface naming code

Changes from v5:
 - adapt to the latest Q/BMan drivers API
 - use build_skb() on Rx path instead of buffer pool refill path
 - proper support for multiple buffer pools
 - align function, variable names, code cleanup
 - driver file structure cleanup

Changes from v4:
 - addressed feedback from Scott Wood and Joe Perches
 - fixed spelling
 - fixed leak of uninitialized stack to userspace
 - fix prints
 - replace raw_cpu_ptr() with this_cpu_ptr()
 - remove _s from the end of structure names
 - remove underscores at start of functions, goto labels
 - remove likely in error paths
 - use container_of() instead of open casts
 - remove priv from the driver name
 - move return type on same line with function name
 - drop DPA_READ_SKB_PTR/DPA_WRITE_SKB_PTR

Changes from v3:
 - removed bogus delay and comment in .ndo_stop implementation
 - addressed minor issues reported by David Miller

Changes from v2:
 - removed debugfs, moved exports to ethtool statistics
 - removed congestion groups Kconfig params

Changes from v1:
 - bpool level Kconfig options removed
 - print format using pr_fmt, cleaned up prints
 - __hot/__cold removed
 - gratuitous unlikely() removed
 - code style aligned, consistent spacing for declarations
 - comment formatting
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add trace points on the hot processing path.
Signed-off-by: NRuxandra Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export Frame Queue and Buffer Pool IDs through sysfs.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a series of counters to be exported through ethtool:
- add detailed counters for reception errors;
- add detailed counters for QMan enqueue reject events;
- count the number of fragmented skbs received from the stack;
- count all frames received on the Tx confirmation path;
- add congestion group statistics;
- count the number of interrupts for each CPU.
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for basic ethtool operations.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This introduces the Freescale Data Path Acceleration Architecture
(DPAA) Ethernet driver (dpaa_eth) that builds upon the DPAA QMan,
BMan, PAMU and FMan drivers to deliver Ethernet connectivity on
the Freescale DPAA QorIQ platforms.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce managed counterparts for alloc_percpu() and free_percpu().
Add devm_alloc_percpu() and devm_free_percpu() into the managed
interfaces list.
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The repair mode is used to get and restore sequence numbers and
data from queues. It used to checkpoint/restore connections.

Currently the repair mode can be enabled for sockets in the established
and closed states, but for other states we have to dump the same socket
properties, so lets allow to enable repair mode for these sockets.

The repair mode reveals nothing more for sockets in other states.
Signed-off-by: NAndrei Vagin <avagin@openvz.org>
Acked-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Raghu Vatsavayi says:

====================
liquidio CN23XX VF support

Following is the V6 patch series for adding VF support on
CN23XX devices. This version addressed:
1) Your concern for ordering of local variable declarations
   from longest to shortest line.
2) Removed module parameters max_vfs, num_queues_per_{p,v}f.
3) Minor changes for fixing new checkpatch script related
   errors on pre-existing driver.
4) Fixed compilation issues when CONFIG_PCI_IOV/CONFIG_PCI_ATS
   options are disabled.
5) Modified qualifiers for printing mac addresses with pM format.

I will post remaining VF patches soon after this patchseries is
applied. Please apply patches in the following order as some of
the patches depend on earlier patches.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New checkpatch script shows some errors with pre-existing
driver. This patch provides fix for those errors.
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updated copyrights comments and also changed some other comments
alignments.
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleaned up unnecessary comments and added some minor macros.
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleaned up resource leaks during destroy resources by
introducing more device states.
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>