If we inherit an error along the fence chain, we skip the main work
callback and go straight to the error. In the case of the vma bind
worker, we only dropped the pinned pages from the worker.

In the process, make sure we call the release earlier rather than wait
until the final reference to the fence is dropped (as a reference is
kept while being listened upon).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216161717.2688274-1-chris@chris-wilson.co.uk

The Gen11+ and the legacy function differ in the register and value
written to interrupt the GuC. However, while on older gen the value
matches a bit on the register, on Gen11+ the value is a SW defined
payload that is sent to the FW. Since the FW behaves the same no matter
what value we pass to it, we can just write the same thing on all gens
and get rid of the function pointer by saving the register offset.
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-6-daniele.ceraolospurio@intel.com

Since we started using CT buffers on all gens, the function pointers can
only be set to either the _nop() or the _ct() functions. Since the
_nop() case applies to when the CT are disabled, we can just handle that
case in the _ct() functions and call them directly.

v2: keep intel_guc_send() and make the CT send/receive functions work on
    intel_guc_ct. (Michal)
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-5-daniele.ceraolospurio@intel.com

For better isolation of the request tracking from the rest of the
CT-related data.

v2: split to separate patch, move next_fence to substructure (Michal)
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-4-daniele.ceraolospurio@intel.com

The GuC supports having multiple CT buffer pairs and we designed our
implementation with that in mind. However, the different channels are not
processed in parallel within the GuC, so there is very little advantage
in having multiple channels (independent locks?), compared to the
drawbacks (one channel can starve the other if messages keep being
submitted to it). Given this, it is unlikely we'll ever add a second
channel and therefore we can simplify our code by removing the
flexibility.

v2: split substructure grouping to separate patch, improve docs (Michal)
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-3-daniele.ceraolospurio@intel.com

We track the status of the GuC much more closely now and we expect the
enable/disable functions to be correctly called only once. If this isn't
true we do want to flag it as a flow failure (via the BUG_ON in the ctch
functions) and not silently ignore the call.
Suggested-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-2-daniele.ceraolospurio@intel.com

The only difference from the GuC POV between guc_communication_stop and
guc_communication_disable is that the former can be called after GuC
has been reset. Instead of having two separate paths, we can just skip
the call into GuC in the disabling path and re-use that.

Note that by using the disable() path instead of the stop() one there
are two additional changes in SW side for the stop path:

- interrupts are now disabled before disabling the CT, which is ok
  because we do not want interrupts with CT disabled;
- guc_get_mmio_msg() is called in the stop case as well, which is ok
  because if there are errors before the reset we do want to record
  them.
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217012316.13271-1-daniele.ceraolospurio@intel.com

Get_pid_task() needs to be paired with a put_pid or we leak a pid
reference every time a banned client tries to create a context.

v2:
 * task_pid_nr helper exists! (Chris)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b083a087 ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217170933.8108-1-tvrtko.ursulin@linux.intel.com

As we stash a pointer to the HWSP cacheline on the request, when reading
it we only need confirm that the cacheline is still valid by checking
that the request and timeline are still intact.

v2: Protect hwsp_cachline with RCU
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217011659.3092130-1-chris@chris-wilson.co.uk

Since commit e5dadff4 ("drm/i915: Protect request retirement with
timeline->mutex"), the request retirement can happen outside of the
struct_mutex serialised only by the timeline->mutex. We drop the
timeline->mutex on submitting the request (i915_request_add) so after
that point, it is liable to be freed. Make sure our local reference is
kept alive until we have finished attaching it to the signalers. (Note
that this erodes the argument that i915_request_add should consume the
reference, but that is a slightly larger patch!)

Fixes: e5dadff4 ("drm/i915: Protect request retirement with timeline->mutex")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217134729.3297818-1-chris@chris-wilson.co.uk

At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).

So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.

On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.

So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012

Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.

This commit fixes using the wrong PWM controller on these devices by
calling pwm_get() for the right PWM controller based on the
VBT dsi.config.pwm_blc bit.

Note this is part of a series which contains 2 other patches which renames
the PWM lookup for the 1st SoC/LPSS PWM from "pwm_backlight" to
"pwm_pmic_backlight" and the PWM lookup for the Crystal Cove PMIC PWM
from "pwm_backlight" to "pwm_pmic_backlight".
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-4-hdegoede@redhat.com

At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.

Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).

So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.

On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.

So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012

Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.

Since only the i915 driver has access to the VBT, this commit renames
the "pwm_backlight" lookup entries for the Crystal Cove PMIC's PWM
controller to "pwm_pmic_backlight" so that the i915 driver can do a
pwm_get() for the right controller depending on the VBT bit, instead of
the i915 driver relying on a "pwm_backlight" lookup getting registered
which magically points to the right controller.
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-3-hdegoede@redhat.com

At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).

So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.

On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.

So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012

Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.

Since only the i915 driver has access to the VBT, this commit renames
the "pwm_backlight" lookup entries for the 1st BYT/CHT LPSS PWM controller
to "pwm_soc_backlight" so that the i915 driver can do a pwm_get() for
the right controller depending on the VBT bit, instead of the i915 driver
relying on a "pwm_backlight" lookup getting registered which magically
points to the right controller.
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-2-hdegoede@redhat.com

Sandybridge is the gen that didn't handle multiple registers in a single
LRI packet. Don't forget it!

Fixes: 902eb748 ("drm/i915/gt: Tidy up full-ppgtt on Ivybridge")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Tested-by: NTomi Sarvela <tomi.p.sarvela@intel.com>
Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217091328.3093551-1-chris@chris-wilson.co.uk

We currently use an error-prone mutex_trylock to grab another timeline
to find an earlier request along it. However, with a bit of a
sleight-of-hand, we can reduce the mutex_trylock to a spin_lock on the
immediate request and careful pointer chasing to acquire a reference on
the previous request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216165317.2742896-1-chris@chris-wilson.co.uk

Signed-off-by: NMaya Rashish <coypu@sdf.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213102630.GA24082@SDF.ORG

With a couple more memory barriers dotted around the place we can
significantly reduce the MTBF on Ivybridge. Still doesn't really help
Haswell though.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216142409.2605211-1-chris@chris-wilson.co.uk

When creating a handle, it is just that, an abstract handle. The fact
that we cannot currently support a handle larger than the size of the
backing storage is an artifact of our whole-object-at-a-time handling in
get_pages() and being an implementation limitation is best handled at
that point -- similar to shmem, where we only barf when asked to
populate the whole object if larger than RAM. (Pinning the whole object
at a time is major hindrance that we are likely to have to overcome in
the near future.) In the case of the buddy allocator, the late check is
preferable as the request size may often be smaller than the required
size.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216122603.2598155-1-chris@chris-wilson.co.uk

typecheck() macro creates an huge stack size causing
issues with static analysis with coverity, addressing
this with creating a local pointer.

Fixes: 639f2f24 ("drm/i915: Introduce new macros for tracing")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216185332.83289-1-venkata.s.dhanalakota@intel.com

Fixes coccicheck warning:

drivers/gpu/drm/i915/gem/i915_gem_region.c:88:2-3: Unneeded semicolon
drivers/gpu/drm/i915/gvt/gtt.c:1285:2-3: Unneeded semicolon
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: Nzhengbin <zhengbin13@huawei.com>
Acked-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1576467845-60920-1-git-send-email-zhengbin13@huawei.com

In some cases like latency[level]==0, wm[level].res_lines>31,
min_ddb_alloc can be U16_MAX, exclude it from the WARN_ON.

v2: Specify the cases in which we hit U16_MAX, indentation (Ville)

Fixes: 10a7e07b ("drm/i915: Make sure cursor has enough ddb for the selected wm level")
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216080619.10945-1-vandita.kulkarni@intel.com

According to both the old acpi_igd_opregion_spec_0.pdf and the newer
skl_opregion_rev0p5.pdf opregion specification documents, if a driver
handles hotplug events itself, it should set the opregion CHPD field to
1 to indicate this and the firmware should respond to this by no longer
sending ACPI 0x00 notification events on e.g. lid-state changes.

Specifically skl_opregion_rev0p5.pdf states thid in the documentation of
the CHPD word: "Re-enumeration trigger logic in System BIOS MUST be
disabled for all the Operating Systems supporting Hot-Plug
(e.g., Windows* Longhorn and above)." Note the MUST in there.

We ignore these notifications, so this should not be a problem but many
recent DSTDs seem to all have the same copy-pasted bug in the GNOT() AML
function which is used to send these notifications. Windows likely does not
hit this bug as it presumably correcty sets CHPD to 1.

Here is an example of the broken GNOT() method:

            Method (GNOT, 2, NotSerialized)
            {
                ...
                CEVT = Arg0
                CSTS = 0x03
                If (((CHPD == Zero) && (Arg1 == Zero)))
                {
                    If (((OSYS > 0x07D0) || (OSYS < 0x07D6)))
                    {
                        Notify (PCI0, Arg1)
                    }
                    Else
                    {
                        Notify (GFX0, Arg1)
                    }
                }
                ...

Notice that the condition for the If is always true I believe that the
|| like needs to be an &&, but there is nothing we can do about this and
in my own DSDT archive 55 of the 93 DSDTs have this issue.

When the if is true the notification gets send to the PCI root instead
of only to the GFX0 device. This causes Linux to re-enumerate PCI devices
whenever the LID opens / closes, leading to unexpected messages in dmesg:

Suspend through lid close:
[  313.598199] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[  313.664453] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[  313.737982] pci_bus 0000:01: Allocating resources
[  313.738036] pcieport 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01] add_size 1000
[  313.738051] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[  313.738111] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0x91000000-0x911fffff 64bit pref]
[  313.738128] pcieport 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]

Resume:
[  813.623894] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000
[  813.623955] pci 0000:00:03.0: reg 0x10: [mem 0x00000000-0x003fffff]
[  813.630477] pci 0000:00:03.0: BAR 0: assigned [mem 0x91c00000-0x91ffffff]
[  854.579101] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3

And more importantly this re-enumeration races with suspend/resume causing
enumeration to not be complete  when assert_isp_power_gated() from
drivers/gpu/drm/i915/display/intel_display_power.c runs. This causes
the !pci_dev_present(isp_ids) check in assert_isp_power_gated() to fail
making the condition for the WARN true, leading to:

[  813.327886] ------------[ cut here ]------------
[  813.327898] ISP not power gated
[  813.328028] WARNING: CPU: 2 PID: 2317 at drivers/gpu/drm/i915/display/intel_display_power.c:4870 intel_display_print_error_state+0x2b98/0x3a80 [i915]
...
[  813.328599] ---[ end trace f01e81b599596774 ]---

This commit fixes the unwanted ACPI notification on the PCI root device
by setting CHPD to 1, so that the broken if condition in the AML never
gets checked as notifications of type 0x00 are disabled altogether.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212204828.191288-1-hdegoede@redhat.com

Wait for the object to be idle before changing its cache-level and
unbinding. This was dropped as supposedly superfluous from commit
8b1c78e0 ("drm/i915: Avoid calling i915_gem_object_unbind holding
object lock"), but it turns out to prevent some cache dirt escaping.
Smells like papering over a race...

Closes: https://gitlab.freedesktop.org/drm/intel/issues/820
Fixes: 8b1c78e0 ("drm/i915: Avoid calling i915_gem_object_unbind holding object lock")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: NAndi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213223140.1830738-1-chris@chris-wilson.co.uk

Commit 4d89adc7 ("drm/i915/display/dsi: Add support to pipe D")
added pipe D support for DSI, but failed to update the state readout.

Fixes: 4d89adc7 ("drm/i915/display/dsi: Add support to pipe D")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191211110844.2996-1-jani.nikula@intel.com

Just like in commit 523e0cc8 ("drm/i915/tgl: allow DVI/HDMI on port
A"), the port checks when reading the VBT can easily not match what the
platform really exposes. However here we only have some additional debug
messages that are not adding much value: in the previous debug message
we already print everything we know about the VBT.

Instead of keep fixing the possible port assignments according to the
platform, just nuke the additional messages.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206190552.8818-1-lucas.demarchi@intel.com

Add two helpers that for reading the actual GT's frequency. The
two helpers are:

 - intel_rps_read_cagf: reads the frequency and returns it not
   normalized

 - intel_rps_read_actual_frequency: provides the frequency in Hz.

Use the above helpers in sysfs and debugfs.
Signed-off-by: NAndi Shyti <andi.shyti@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213183736.31992-2-andi@etezian.org

While not good behaviour, it is, however, established behaviour that we
can punt EAGAIN to userspace if we need to retry the ioctl. When trying
to acquire a mutex, prefer to use EAGAIN to propagate losing the race
so that if it does end up back in userspace, we try again.

Fixes: c81471f5 ("drm/i915: Copy across scheduler behaviour flags across submit fences")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/800Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213160347.1789004-1-chris@chris-wilson.co.uk

New macros ENGINE_TRACE(), CE_TRACE(), RQ_TRACE() and
GT_TRACE() are introduce to tag device name and engine
name with contexts and requests tracing in i915.

Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213155152.69182-2-venkata.s.dhanalakota@intel.com

We do not require to register the sysctl paths per instance,
so making registration global.

v2: make sysctl path register and unregister function driver
    specific (Tvrtko and Lucas).

Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213155152.69182-1-venkata.s.dhanalakota@intel.com

Now that the combo PHY aux power well handlers are used exclusively on
Icelake, we can drop a bunch of the extra tests.

v2: Don't try to use intel_uncore_rmw for register updates yet; there's
    pending display uncore patches that need to land first.  (Lucas)

v3: Drop the combo phy assertion.  It was backward before, but doesn't
    seem terribly necessary.  I'm keeping the IS_ICELAKE assertion
    though since we often copy/paste/modify the power well tables when
    defining new platforms and it's too easy to cargo cult the
    ICL-specific handling to new platforms that shouldn't use it.
    (Lucas)

v4: Fix build; forgot to commit all the changes.  (CI)

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213010600.701315-1-matthew.d.roper@intel.comReviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>

The TGL workaround database no longer shows Wa #1178 (or anything
similar under different workaround names/numbers) so we should be able
to drop it.  In fact Swati just discovered that applying this workaround
is the root cause of some power well enable failures we've been seeing
in CI (gitlab issue 498).

Once we stop applying this WA, TGL no longer utilizes any of the special
handling provided by icl_combo_phy_aux_power_well_ops so we can just
drop back to using the standard hsw-style power well ops instead.

v3: Drop now-unused _TGL_AUX_ANAOVRD1_C definition too.  (Lucas)

Closes: https://gitlab.freedesktop.org/drm/intel/issues/498
Fixes: deea06b4 ("drm/i915/tgl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213001511.678070-3-matthew.d.roper@intel.com

Outputs C and D on EHL are combo PHY outputs and thus should not be
using the same TC AUX power well handlers as ICL.  And even though
icl_combo_phy_aux_power_well_ops works okay for EHL/JSL combo PHYs none
of its special handling is actually necessary for this platform:
 * EHL/JSL don't actually need to program PORT_CL_DW12
 * Display WA #1178 does not apply to EHL/JSL

Thus we can simply drop back to using our standard "hsw-style" power
well ops for EHL AUX power wells.

Bspec: 4301
Fixes: f722b8c1 ("drm/i915/ehl: All EHL ports are combo phys")
Cc: Jose Souza <jose.souza@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213001511.678070-2-matthew.d.roper@intel.comReviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>

We know that "err" is non-zero so there is no need to check.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213105050.y2v5nylsuxvc44jj@kili.mountain

The "num_dtd" variable is the number of elements in the
generic_dtd->dtd[] array so the > needs to be >= to prevent reading one
element beyond the end of the array.

Fixes: 33ef6d4f ("drm/i915/vbt: Handle generic DTD block")
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212091130.zf2g53njf5u24wk6@kili.mountain

skl_commit_modeset_enables() is a bit of mess. Let's streamline
it by simply tracking which pipes still need to be updated.
As a bonus we get rid of the state->wm_results.dirty_pipes usage.

v2: Rebase due to port sync

Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v1
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210144105.3239-2-ville.syrjala@linux.intel.com

U series device need different DDI buffer setup for eDP
and DP. If driver did not recognize ULT id proerply.
The setting for H and S series would be used.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: NLee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210150415.10705-2-shawn.c.lee@intel.com

commit 'a7b4deeb ("drm/i915/cml: Add CML PCI IDS)'
introduced new PCI ID that CML support. But some PCI
IDs were removed in BSpec for CML. This patch is used
to eliminate the unsed ID.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: NLee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210150415.10705-1-shawn.c.lee@intel.com

drivers/gpu/drm/i915/gt/intel_rps.c:1726:24: error: incompatible types in comparison expression (different address spaces):
drivers/gpu/drm/i915/gt/intel_rps.c:1726:24:    struct drm_i915_private [noderef] <asn:4> *
drivers/gpu/drm/i915/gt/intel_rps.c:1726:24:    struct drm_i915_private *
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVenkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212140459.1307617-7-chris@chris-wilson.co.uk

Since dma_fence_init may call ops (because of a meaningless
trace_dma_fence), we need to set the worker ops prior to that call.
Reported-by: NVince Weaver <vincent.weaver@maine.edu>
Fixes: 8e458fe2 ("drm/i915: Generalise the clflush dma-worker")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212154224.1631531-1-chris@chris-wilson.co.uk

On non-debug builds we were not using i915 param and thus
we may cause "unused variable" warning/error if caller was
not using i915 elsewhere. Let compiler see this param.
Signed-off-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212121903.72524-1-michal.wajdeczko@intel.com