We use the same buffer I/O failure code in a few different places.
It's not much code, but it's not necessarily self-explanatory.
Factor it into a helper and document it in one place.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NAllison Collins <allison.henderson@oracle.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Flush locked log items whose underlying buffers fail metadata
writeback are tagged with a special flag to indicate that the flush
lock is already held. This is currently implemented in the type
specific ->iop_push() callback, but the processing required for such
items is not type specific because we're only doing basic state
management on the underlying buffer.

Factor the failed log item handling out of the inode and dquot
->iop_push() callbacks and open code the buffer resubmit helper into
a single helper called from xfsaild_push_item(). This provides a
generic mechanism for handling failed metadata buffer writeback with
a bit less code.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NAllison Collins <allison.henderson@oracle.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Make sure we release resources properly if we cannot clean out the COW
extents in preparation for an extent swap.

Fixes: 96987eea ("xfs: cancel COW blocks before swapext")
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>

The functionality in xfs_diflags_to_linux() and xfs_diflags_to_iflags() are
nearly identical.  The only difference is that *_to_linux() is called after
inode setup and disallows changing the DAX flag.

Combining them can be done with a flag which indicates if this is the initial
setup to allow the DAX flag to be properly set only at init time.

So remove xfs_diflags_to_linux() and call the modified xfs_diflags_to_iflags()
directly.

While we are here simplify xfs_diflags_to_iflags() to take struct xfs_inode and
use xfs_ip2xflags() to ensure future diflags are included correctly.
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

xfs_inode_supports_dax() should reflect if the inode can support DAX not
that it is enabled for DAX.

Change the use of xfs_inode_supports_dax() to reflect only if the inode
and underlying storage support dax.

Add a new function xfs_inode_should_enable_dax() which reflects if the
inode should be enabled for DAX.
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

As agreed upon[1].  We make the dax mount option a tri-state.  '-o dax'
continues to operate the same.  We add 'always', 'never', and 'inode'
(default).

[1] https://lore.kernel.org/lkml/20200405061945.GA94792@iweiny-DESK2.sc.intel.com/Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

In prep for the new tri-state mount option which then introduces
XFS_MOUNT_DAX_NEVER.
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

An earlier call of xfs_reinit_inode() from xfs_iget_cache_hit() already
handles initialization of i_rwsem.

Doing so again is unneeded.
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Given how XFS is all based around btrees it doesn't make much sense
to offer a totally generic state when we can just use the btree cursor.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

All defer op instance place their own extension of the log item into
the dfp_done field.  Replace that with a xfs_log_item to improve type
safety and make the code easier to follow.

Also use the opportunity to improve the ->finish_item calling conventions
to place the done log item as the higher level structure before the
list_entry used for the individual items.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Split out a helper that operates on a single xfs_defer_pending structure
to untangle the code.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

All defer op instance place their own extension of the log item into
the dfp_intent field.  Replace that with a xfs_log_item to improve type
safety and make the code easier to follow.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

This avoids a per-item indirect call, and also simplifies the interface
a bit.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

These are aways called together, and my merging them we reduce the amount
of indirect calls, improve type safety and in general clean up the code
a bit.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Create a helper that encapsulates the whole logic to create a defer
intent.  This reorders some of the work that was done, but none of
that has an affect on the operation as only fields that don't directly
interact are affected.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Split out a xlog_add_buffer_cancelled helper which does the low-level
manipulation of the buffer cancelation table, and in that helper call
xlog_find_buffer_cancelled instead of open coding it.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Don't bother to allocate memory and convert the log item when we
only need the block number and the length.  Just extract them directly
and call xlog_buf_readahead separately in each branch.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Add a little helper to readahead a buffer if it hasn't been cancelled.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

This list contains pretty much everything that is not a buffer.  The
comment calls it item_list, which is a much better name than inode
list, so switch the actual variable name to that as well.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Replace the somewhat convoluted use of xlog_peek_buffer_cancelled and
xlog_check_buffer_cancelled with two obvious helpers:

 xlog_is_buffer_cancelled, which returns true if there is a buffer in
 the cancellation table, and
 xlog_put_buffer_cancelled, which also decrements the reference count
 of the buffer cancellation table.

Both share a little helper to look up the entry.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

There are a couple places where we directly call printk_once() and one
of them doesn't follow the standard xfs subsystem printk format as a
result.

#define printk_once variants to go with our existing printk_ratelimited
#defines so we can do one-shot printks in a consistent manner.
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

I ran into a linker warning in XFS that originates from a mismatch
between libelf, binutils and objtool when certain files in the kernel
are built with "gcc -g":

x86_64-linux-ld: fs/xfs/xfs_trace.o: unable to initialize decompress status for section .debug_info

After some discussion, nobody could identify why xfs sets this flag
here. CONFIG_XFS_DEBUG used to enable lots of unrelated settings, but
now its main purpose is to enable extra consistency checks and assertions
that are unrelated to the debug info.

Remove the Makefile logic to set the flag here. If anyone relies
on the debug info, this can simply be enabled again with the global
CONFIG_DEBUG_INFO option.

Dave Chinner writes:

I'm pretty sure it was needed for the original kgdb integration back
in the early 2000s. That was when SGI used to patch their XFS dev
tree with kgdb and debug symbols were needed by the custom kgdb
modules that were ported across from the Irix kernel debugger.

ISTR that the early kcrash kernel dump analysis tools (again,
originated from the Irix "icrash" kernel dump tools) had custom XFS
debug scripts that needed also the debug info to work correctly...

Which is a long way of saying "we don't need it anymore" instead of
"nobody knows why it was set"... :)
Suggested-by: NChristoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/lkml/20200409074130.GD21033@infradead.org/Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NAllison Collins <allison.henderson@oracle.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Since the "no-allocation" reservations has been removed, the resblks
value should be larger than zero, so remove the unnecessary check.
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Simplify the setting of the flags value, and only consider
quota enforcement stuff here.
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The check XFS_IS_QUOTA_RUNNING() has been done when enter the
xfs_qm_vop_create_dqattach() function, it will return directly
if the result is false, so the followed XFS_IS_QUOTA_RUNNING()
assertion is unnecessary. If we truly care about this, the check
also can be added to the condition of next if statements.
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The initial value of variable udqp is NULL, and we only set the
flag XFS_QMOPT_PQUOTA in xfs_qm_vop_dqalloc() function, so only
the pdqp value is initialized and the udqp value is still NULL.
Since the udqp value is NULL in the rest part of xfs_ioctl_setattr()
function, it is meaningless and do nothing. So remove it from
xfs_ioctl_setattr().
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

We share an inode between gquota and pquota with the older
superblock that doesn't have separate pquotino, and for the
need_alloc == false case we don't need to call xfs_dir_ialloc()
function, so add the check if reserved free disk blocks is
needed.
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The two if statements have same condition, and the mask value
does not change in xfs_setattr_nonsize(), so combine them.
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NChaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The trace event xfs_dquot_dqalloc does not depend on the
value uq, so remove the condition, and trace quota allocations
for all quota types.
Signed-off-by: NKaixu Xia <kaixuxia@tencent.com>
Reviewed-by: NChaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

When we're sorting recovered log items ahead of recovering them and
encounter a log item of unknown type, actually print the type code when
we're rejecting the whole transaction to aid in debugging.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>

Pull more btrfs fixes from David Sterba:
 "A few more stability fixes, minor build warning fixes and git url
  fixup:

   - fix partial loss of prealloc extent past i_size after fsync

   - fix potential deadlock due to wrong transaction handle passing via
     journal_info

   - fix gcc 4.8 struct intialization warning

   - update git URL in MAINTAINERS entry"

* tag 'for-5.7-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  MAINTAINERS: btrfs: fix git repo URL
  btrfs: fix gcc-4.8 build warning for struct initializer
  btrfs: transaction: Avoid deadlock due to bad initialization timing of fs_info::journal_info
  btrfs: fix partial loss of prealloc extent past i_size after fsync

Pull IOMMU fixes from Joerg Roedel:

 - Fix a memory leak when dev_iommu gets freed and a sub-pointer does
   not

 - Build dependency fixes for Mediatek, spapr_tce, and Intel IOMMU
   driver

 - Export iommu_group_get_for_dev() only for GPLed modules

 - Fix AMD IOMMU interrupt remapping when x2apic is enabled

 - Fix error path in the QCOM IOMMU driver probe function

* tag 'iommu-fixes-v5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/qcom: Fix local_base status check
  iommu: Properly export iommu_group_get_for_dev()
  iommu/vt-d: Use right Kconfig option name
  iommu/amd: Fix legacy interrupt remapping for x2APIC-enabled system
  iommu: spapr_tce: Disable compile testing to fix build on book3s_32 config
  iommu/mediatek: Fix MTK_IOMMU dependencies
  iommu: Fix the memory leak in dev_iommu_free()

The git repo listed for btrfs hasn't been updated in over a year.
List the current one instead.
Signed-off-by: NEric Biggers <ebiggers@google.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Pull power management fixes from Rafael Wysocki:

 - prevent the intel_pstate driver from printing excessive diagnostic
   messages in some cases (Chris Wilson)

 - make the hibernation restore kernel freeze kernel threads as well as
   user space tasks (Dexuan Cui)

 - fix the ACPI device PM disagnostic messages to include the correct
   power state name (Kai-Heng Feng).

* tag 'pm-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: ACPI: Output correct message on target power state
  PM: hibernate: Freeze kernel threads in software_resume()
  cpufreq: intel_pstate: Only mention the BIOS disabling turbo mode once

* pm-cpufreq:
  cpufreq: intel_pstate: Only mention the BIOS disabling turbo mode once

* pm-sleep:
  PM: hibernate: Freeze kernel threads in software_resume()