This patch adds support for the three new SDR formats. These formats
were prefixed with "planar" indicating I & Q data are not interleaved
as in other formats. Here, I & Q data constitutes the top half and bottom
half of the received buffer respectively.

V4L2_SDR_FMT_PCU16BE - 14-bit complex (I & Q) unsigned big-endian sample
inside 16-bit. V4L2 FourCC: PC16

V4L2_SDR_FMT_PCU18BE - 16-bit complex (I & Q) unsigned big-endian sample
inside 18-bit. V4L2 FourCC: PC18

V4L2_SDR_FMT_PCU20BE - 18-bit complex (I & Q) unsigned big-endian sample
inside 20-bit. V4L2 FourCC: PC20
Signed-off-by: NRamesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: NHans Verkuil <hansverk@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch adds driver support for the MAX2175 chip. This is Maxim
Integrated's RF to Bits tuner front end chip designed for software-defined
radio solutions. This driver exposes the tuner as a sub-device instance
with standard and custom controls to configure the device.
Signed-off-by: NRamesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: NHans Verkuil <hansverk@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use the needs-hpd DT property to determine if the CEC_CAP_NEEDS_HPD
should be set.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add a new capability CEC_CAP_NEEDS_HPD. If this capability is set
then the hardware can only use CEC if the HDMI Hotplug Detect pin
is high. Such hardware cannot handle the corner case in the CEC specification
where it is possible to transmit messages even if no hotplug signal is
present (needed for some displays that turn off the HPD when in standby,
but still have CEC enabled).

Typically hardware that needs this capability have the HPD wired to the CEC
block, often to a 'power' or 'active' pin.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use the helper function cec_transmit_attempt_done instead of
cec_transmit_done to simplify the code.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

A simpler variant of cec_transmit_done to be used where the HW does
just a single attempt at a transmit. So if the status indicates an
error, then the corresponding error count will always be 1 and this
function figures that out based on the status argument.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This function simplifies the integration of CEC in DRM drivers.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix the position of arguments so camif->colorfx_cb, camif->colorfx_cr
are passed in proper order to the camif_hw_set_effect() function.

Addresses-Coverity-ID: 1248800
Addresses-Coverity-ID: 1269141

[s.nawrocki@samsung.com: edited commit message ]
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As this is not in atomic context and it does not seem like a critical
timing setting a range of 1ms allows the timer subsystem to optimize
the hrtimer here.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use colorspace provided by the user as we are only doing scaling and
color encoding conversion, we won't be able to transform the colorspace
itself and the colorspace won't mater in that operation.

Also always use output colorspace on the capture side.

If the user does not provide a colorspace do not make it up, we might
later while processing need to figure out the colorspace, which
is possible depending on the frame size but do not ever guess and
leak that guess to the userspace.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NThibault Saunier <thibault.saunier@osg.samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Usage of devm_of_platform_populate() simplify driver code
and save somes lines
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Trivial fix to spelling mistake in mfc_err error messages
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

v4l2_m2m_job_finish(), which is called from the interrupt handler with
slock acquired, can call the device_run() hook immediately if another
context was in the queue. This hook also acquires slock, resulting in
a deadlock for this scenario.

Fix this by releasing slock right before calling v4l2_m2m_job_finish().
This is safe to do as the state of the hardware cannot change before
v4l2_m2m_job_finish() is called anyway.
Signed-off-by: NAlexandre Courbot <acourbot@chromium.org>
Acked-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.

The dev->initialized commits that are relevant are commit c73bbaa4
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9 ("[media] rc: add locking to fix register/show race").

The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.

At the same time, remove the bogus "device is being removed" check.
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The device core infrastructure is based on the presumption that
once a driver calls device_add(), it must be ready to accept
userspace interaction.

This requires splitting rc_setup_rx_device() into two functions
and reorganizing rc_register_device() so that as much work
as possible is performed before calling device_add().
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This module was merged after commit 5a8fc6a3 ("Annotate hardware
config module parameters in drivers/media/"), so add add the missing
hardware annotations.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch add cec driver for STM32 platforms.
cec hardware block isn't not always used with hdmi so
cec notifier is not implemented. That will be done later
when STM32 DSI driver will be available.

Driver compliance has been tested with cec-ctl and cec-compliance
tools.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NYannick Fertre <yannick.fertre@st.com>
[hans.verkuil@cisco.com: modified platform/Makefile to use obj-y]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The buffer cache should be synchronised in buffer preparation, not when
the buffer is queued to the device. Fix this.

Mmap buffers do not need cache synchronisation since they are always
coherent.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Rename __qbuf_*() functions which are specific to a buffer type as
__prepare_*() which matches with what they do. The naming was there for
historical reasons; the purpose of the functions was changed without
renaming them.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The async sub-device was not unregistered in ad5820_remove() as it should
have been; do it now. Also remove the now-redundant
v4l2_device_unregister_subdev().
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Depending on arch configs to include dirs is evil, and makes
harder to change drivers to work with COMPILE_TEST.

Replace them by obj-y.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The DaVinci VPIF capture driver V4L2 OF support was added after the V4L2
OF framework got removed. Switch VPIF capture driver to V4L2 fwnode.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>

The 2nd check of cnt > 8 is redundant as cnt is already checked
and thresholded to a maximum of 8 a few statements earlier.
Remove this redundant 2nd check.

Detected by CoverityScan, CID#114281 ("Logically dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Some EXPORT_SYMBOL() on this file don't match the name of functions
that preceeds them.

Also, some kernel-doc markups also have a wrong name. Fix it.
Signed-off-by: NJasmin Jessich <jasmin@anw.at>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Make checkpatch happier by fixing this warning:
  ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: NJasmin Jessich <jasmin@anw.at>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

A driver error message is shown without DEBUG definition
to find an error and debug easily.
Signed-off-by: NHirokazu Honda <hiroh@chromium.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

If the mdp_* nodes are under an mdp sub-node, their corresponding
platform device does not automatically get its iommu assigned properly.

Fix this by moving the mdp component nodes up a level such that they are
siblings of mdp and all other SoC subsystems.  This also simplifies the
device tree.

Although it fixes iommu assignment issue, it also break compatibility
with old device tree. So, the patch in driver is needed to iterate over
sibling mdp device nodes, not child ones, to keep driver work properly.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NMinghsiu Tsai <minghsiu.tsai@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

That way we don't have to rely on userspace to inject the headers on IDR
requests, and there is always enough information to start decoding at an
I-frame.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME control to force IDR
frames. This is useful to implement VFU (Video Fast Update) on RTP
transmissions.
We already force an IDR frame at the beginning of each GOP to work
around a firmware bug on i.MX27, use the same mechanism to service IDR
requests from userspace.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The driver may sleep under a spin lock, and the function call path is:
snd_cx18_pcm_hw_free (acquire the lock by spin_lock_irqsave)
  vfree --> may sleep

To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)']
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The driver may sleep under a spin lock, and the function call path is:
snd_ivtv_pcm_hw_free (acquire the lock by spin_lock_irqsave)
  vfree --> may sleep

To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: NJia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)']
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The current driver has a handful of hard-coded assumptions based on its
primary use for capture of video signals.  Cleanup those assumptions,
and also query the subdev for format information and use that if
available.

Tested with 10-bit raw bayer input (SGRBG10) using the aptina,mt9v032
sensor, and also tested that composite video input still works from
ti,tvp514x decoder.  Both tests done on the da850-evm board with the
add-on UI board.

NOTE: Will need further testing for other sensors with different bus
formats.
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Enable  getting of subdevs from DT ports and endpoints.

The _get_pdata() function was larely inspired by (i.e. stolen from)
am437x-vpfe.c
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Capture driver silently overrides pixel format with a hack (according to
the comments) to pass v4l2 compliance tests.  This isn't needed for
normal functionality, and works for composite video and raw camera capture
without.

In addition, the hack assumes that it only supports raw capture with a
single format (SBGGR8) which isn't true.  VPIF can also capture 10- and
12-bit raw formats as well.  Forthcoming patches will enable VPIF
input with raw-camera support and has been tested with 10-bit format
from the aptina,mt9v032 sensor.

Any compliance failures should be fixed with a real fix.
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The ir-spi driver has 2 issues which prevents it from working with
lirc:

1. The ir-spi driver uses 16 bits of SPI data to create one cycle of
the waveform. As such our SPI clock needs to be 16x faster than the
carrier frequency.

The driver is inconsistent in how it currently handles this. It
initializes it to the carrier frequency:

But the commit message has some example code which initialises it
to 16x the carrier frequency:

	val = 608000;
	ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val);

To maintain compatibility with lirc, always do the frequency adjustment
in the driver.

2. lirc presents pulses in microseconds, but the ir-spi driver treats
them as cycles of the carrier. Similar to other lirc drivers, do the
conversion with DIV_ROUND_CLOSEST().

Fixes: fe052da4 ("[media] rc: add support for IR LEDs driven through SPI")

Cc: stable@vger.kernel.org
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Drop a since commit e1159cb3 ("[media] mceusb: remove pointless
mce_flush_rx_buffer function") redundant reinitialisation of two urb
fields immediately after they have been initialised.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix urb and transfer-buffer leaks in an urb-submission error path which
may be hit when a device is disconnected.

Fixes: 66e89522 ("V4L/DVB: IR: add mceusb IR receiver driver")

Cc: stable <stable@vger.kernel.org>     # 2.6.36
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

interrupts is listed as an optional property in the DT
binding, but in reality the driver didn't work without it.
The existing driver relied on having the interrupt line
connected to the SoC to trigger handling various events.

Add the option to poll the interrupt status register via
a timer if no interrupt source is defined.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Previously the mbus_fmt_code was set after the device was
registered. If a connected sub-device called tc358743_get_fmt
prior to that point it would get an invalid code back.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>