uart_get_baud_rate() will return baud == 0 if the max rate is set
to the "magic" 38400 rate and the SPD_* flags are also specified.
On the first iteration, if the current baud rate is higher than the
max, the baud rate is clamped at the max (which in the degenerate
case is 38400). On the second iteration, the now-"magic" 38400 baud
rate selects the possibly higher alternate baud rate indicated by
the SPD_* flag. Since only two loop iterations are performed, the
loop is exited, a kernel WARNING is generated and a baud rate of
0 is returned.

Reproducible with:
 setserial /dev/ttyS0 spd_hi base_baud 38400

Only perform the "magic" 38400 -> SPD_* baud transform on the first
loop iteration, which prevents the degenerate case from recognizing
the clamped baud rate as the "magic" 38400 value.
Reported-by: NRobert Święcki <robert@swiecki.net>
Cc: <stable@vger.kernel.org> # all
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The atmel serial driver uses dmaengine APIs but never included the dmaengine
header as it was getting inculded thru one of driver headers.

commit 3d588f83 - "dmaengine: dw: split
dma-dw.h to platform and private parts" broke this as it moved headers
around.  Fix this by doing the right thing to include the dmaengine header
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: 08f738be (serial: at91: add tx dma support)
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.

Replace the uses with standard structure definitions instead.  This is
similar to pci and usb device registration.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

This reverts commit a86713b1.

Kevin Hilman writes:

	Multiple boot failures on ARM[1] were bisected down to this
	patch.

	How was this patch tested, and on which platforms?

	Also, the changelog states that this should be done only for
	UART_CAP_SLEEP, but the patch does it for every UART.

	Greg, I suggest this patch be dropped from tty-next until it has
	been better described and tested.

	[1] http://lists.linaro.org/pipermail/kernel-build-reports/2014-October/005550.htmlReported-by: NKevin Hilman <khilman@kernel.org>
Cc: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need for yet another copy of the command line, just
use boot_command_line like everyone else.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add support for DT based and command line based early console on platforms
with the msm serial hardware.

Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For console devices having UART_CAP_SLEEP capability, the uart_pm_state has
to be initialized to UART_PM_STATE_ON. Otherwise the LCR regiser values
are reinitialized when uart_change_pm is called from uart_configure_port.
Signed-off-by: NSudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 08177ece ("serial: asc: Adopt readl_/writel_relaxed()) is
regressing the m68k allmodconfig build. This is due to the unconditional
use of readl_relaxed() which, although documented, does not currently
exist for m68k.

This is trivially fixable for st-asc because we can just update the
asc_in() accessor to make this conditional.
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds PM suspend/resume support for the of-serial driver
to provide power management support on devices attatched to it.
Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the metag_da console channel is write only, it doesn't get
polled for incoming data. This is for performance & latency reasons as
polling blocks the processor for a significant amount of time waiting
for the JTAG probe to respond to the request and restart the thread.
This means that the console channel cannot be used for a login prompt,
so ttyDA2 is usually used instead.

In a virtual environment with a virtual DA such as QEMU however the
polling is much cheaper as the request can be handled immediately. It is
useful to be able to enable polling in such an environment in order to
get both the kernel log and a usable login prompt on the same DA
channel.

Add a console_poll module parameter which allows polling to be enabled
for the console channel. It defaults to off as that is the current
behaviour for good reason on real hardware.

It can be enabled by appending metag_da.console_poll to the kernel
command line.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It should not be used together with Auto Flow Control, and
Auto Flow Control is always enabled on Baytrail.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add earlycon support for the cadence serial port.
This is based on recent patches:
"tty/serial: pl011: add generic earlycon support"
(sha1: 0d3c673e)
"tty/serial: add arm/arm64 semihosting earlycon"
(sha1: d50d7269)
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The wait_event() makes the application hang for ever in the following case:
 [1] the hardware flow control is enabled.
 [2] the other end (or the remote end) is terminated, and the TX is still
     waiting for the hardware flow control signal to become asserted.

This patch fixes it by changing the wait_event to wait_event_interruptible.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the uart port is suspending, the RX data is useless.
So in this case, we can terminate the RX DMA right now.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

when the 'CTSC' bit is negated. 'CTS' has no function when 'CTSC' is asserted.
0: The CTS pin is high (inactive)
1: The CTS pin is low (active)

For throttle, it needs to clear 'CTS' and 'CTSC' bits.
For unthrottle, it needs to enable 'CTS' and 'CTSC' bits.

The patch just fix the issue.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.

Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.

This patch enables standard 8250 mode
Signed-off-by: NBryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

To determine the correct divisor, we need to know the difference between
the desired baud rate and the actual baud rate. The calculation for this
difference is implemented twice within omap_serial_baud_is_mode16().
Pull out the calculation for easier maintenance.

While at it, remove the CamelCasing from the variable names.
Signed-off-by: NFrans Klaver <frans.klaver@xsens.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.

Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: NFrans Klaver <frans.klaver@xsens.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The backend type is chosen by the toolstack. Regardless, the frontend
should not care, especially given that it cannot have an effect as the
backend is started before this code is run.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

serial8250_do_startup() adds UART_IER_RDI and UART_IER_RLSI to ier.
serial8250_stop_rx() should remove both.
This is what the serial-omap driver has been doing and is now moved to
the 8250-core since it does no look to be *that* omap specific.
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tony noticed that the old omap-serial driver picked the uart "number"
based on the hint given from device tree or platform device's id.
The 8250 based omap driver doesn't do this because the core code does
not honour the ->line argument which is passed by the driver.

This patch aims to keep the same behaviour as with omap-serial. The
function will first try to use the line suggested ->line argument and
then fallback to the old strategy in case the port is taken.

That means the the third uart will always be ttyS2 even if the previous
two have not been enabled in DT.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial8250_do_startup() function unconditionally clears the
interrupts and for that it reads from the RX-FIFO without checking if
there is a byte in the FIFO or not. This works fine on OMAP4+ HW like
AM335x or DRA7.
OMAP3630 ES1.1 (which means probably all OMAP3 and earlier) does not like
this:

|Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000
|Internal error: : 1028 [#1] ARM
|Modules linked in:
|CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-00022-g7edcb57-dirty #1213
|task: de0572c0 ti: de058000 task.ti: de058000
|PC is at mem32_serial_in+0xc/0x1c
|LR is at serial8250_do_startup+0x220/0x85c
|Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
|Control: 10c5387d  Table: 80004019  DAC: 00000015
|[<c03051d4>] (mem32_serial_in) from [<c0307fe8>] (serial8250_do_startup+0x220/0x85c)
|[<c0307fe8>] (serial8250_do_startup) from [<c0309e00>] (omap_8250_startup+0x5c/0xe0)
|[<c0309e00>] (omap_8250_startup) from [<c030863c>] (serial8250_startup+0x18/0x2c)
|[<c030863c>] (serial8250_startup) from [<c030394c>] (uart_startup+0x78/0x1d8)
|[<c030394c>] (uart_startup) from [<c0304678>] (uart_open+0xe8/0x114)
|[<c0304678>] (uart_open) from [<c02e9e10>] (tty_open+0x1a8/0x5a4)
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.

NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.

v5…v8:
	- drop RPM from serial8250_set_mctrl() it will be used in
	  restore path which already has RPM active and holds
	  dev->power.lock
v4…v5:
	- add a wrapper around rpm function and introduce UART_CAP_RPM
	  to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
	- added runtime to the console code
	- removed device_may_wakeup() from serial8250_set_sleep()

Cc: mika.westerberg@linux.intel.com
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The OMAP UART provides support for HW assisted flow control. What is
missing is the support to throttle / unthrottle callbacks which are used
by the omap-serial driver at the moment.
This patch adds the callbacks. It should be safe to add them since they
are only invoked from the serial_core (uart_throttle()) if the feature
flags are set.
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

While transmitting a START/STOP char for tcflow(TCION/TCIOFF), prevent
a termios change. Otherwise, a garbage in-band flow control char
may be sent, if the termios change overlaps the transmission setup.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Relocate the file-scope function, send_prio_char(), as a global
helper tty_send_xchar(). Remove the global declarations for
tty_write_lock()/tty_write_unlock(), as these are file-scope only now.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use newly-introduced tty->flow_lock to serialize updates to
tty->flow_stopped (via tcflow()) and with concurrent tty flow
control changes from other sources.

Merge the storage for ->stopped and ->flow_stopped, now that both
flags are serialized by ->flow_lock.

The padding bits are necessary to force the compiler to allocate the
type specified; otherwise, gcc will ignore the type specifier and
allocate the minimum number of bytes necessary to store the bitfield.
In turn, this would allow Alpha EV4 and EV5 cpus to corrupt adjacent
byte storage because those cpus use RMW to store byte and short data.

gcc versions < 4.7.2 will also corrupt storage adjacent to bitfields
smaller than unsigned long on ia64, ppc64, hppa64 and sparc64, thus
requiring more than unsigned int storage (which would otherwise be
sufficient to workaround the Alpha non-atomic byte/short storage problem).
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When a master pty is set to packet mode, flow control changes to
the slave pty cause notifications to the master pty via reads and
polls. However, these tests are occurring for all ttys, not
just ptys.

Implement flow control packet mode notifications in the pty driver.
Only the slave side implements the flow control handlers since
packet mode is asymmetric; the master pty receives notifications
for slave-side changes, but not vice versa.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Without serialization, the flow control state can become inverted
wrt. the actual hardware state. For example,

CPU 0                          | CPU 1
stop_tty()                     |
  lock ctrl_lock               |
  tty->stopped = 1             |
  unlock ctrl_lock             |
                               | start_tty()
                               |   lock ctrl_lock
                               |   tty->stopped = 0
                               |   unlock ctrl_lock
                               |   driver->start()
  driver->stop()               |

In this case, the flow control state now indicates the tty has
been started, but the actual hardware state has actually been stopped.

Introduce tty->flow_lock spinlock to serialize tty flow control changes.
Split out unlocked __start_tty()/__stop_tty() flavors for use by
ioctl(TCXONC) in follow-on patch.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

uart_set_termios() is called with interrupts enabled; no need to
save and restore the interrupt state when taking the uart port lock.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 64851636,
serial: bfin-uart: Remove ASYNC_CTS_FLOW flag for hardware automatic CTS,
open-codes uart_handle_cts_change() when CONFIG_SERIAL_BFIN_HARD_CTSRTS
to skip start and stop tx.

But the CTS interrupt handler _still_ calls uart_handle_cts_change();
only call uart_handle_cts_change() if !CONFIG_SERIAL_BFIN_HARD_CTSRTS.

cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

tty->hw_stopped is not used by the tty core and is thread-unsafe;
hw_stopped is a member of a bitfield whose fields are updated
non-atomically and no lock is suitable for serializing updates.

Replace serial core usage of tty->hw_stopped with uport->hw_stopped.
Use int storage which works around Alpha EV4/5 non-atomic byte storage,
since uart_port uses different locks to protect certain fields within the
structure.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.

Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The serial core provides two helper functions, uart_handle_dcd_change()
and uart_handle_cts_change(), for UART drivers to use at interrupt
time. The serial core expects the UART driver to hold the uart port lock
when calling these helpers to prevent state corruption.

If lockdep enabled, trigger a warning if the uart port lock is not held
when calling these helper functions.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We are trying to smoke out the use of the return value from
gpiochip_remove() from the kernel, this has been missed.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch fixes COMPILE_TEST build of serial_mctrl_gpio module for
architectures with custom termios.h header.

sparc64:allmodconfig:

In file included from drivers/tty/serial/serial_mctrl_gpio.c:21:0:
include/uapi/asm-generic/termios.h:22:8: error: redefinition of 'struct termio'
./arch/sparc/include/uapi/asm/termbits.h:16:8: note: originally defined here
make[3]: *** [drivers/tty/serial/serial_mctrl_gpio.o] Error 1
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

schedule(), io_schedule() and schedule_timeout() always return
with TASK_RUNNING state set, so one more setting is unnecessary.

(All places in patch are visible good, only exception is
 kiblnd_scheduler() from:

      drivers/staging/lustre/lnet/klnds/o2iblnd/o2iblnd_cb.c

 Its schedule() is one line above standard 3 lines of unified diff)

No places where set_current_state() is used for mb().
Signed-off-by: NKirill Tkhai <ktkhai@parallels.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1410529254.3569.23.camel@tkhai
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Anil Belur <askb23@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: David Howells <dhowells@redhat.com>
Cc: Dmitry Eremin <dmitry.eremin@intel.com>
Cc: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Isaac Huang <he.huang@intel.com>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Liang Zhen <liang.zhen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Masaru Nomura <massa.nomura@gmail.com>
Cc: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Oleg Drokin <green@linuxhacker.ru>
Cc: Peng Tao <bergwolf@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: devel@driverdev.osuosl.org
Cc: dm-devel@redhat.com
Cc: dri-devel@lists.freedesktop.org
Cc: fcoe-devel@open-fcoe.org
Cc: jfs-discussion@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-afs@lists.infradead.org
Cc: linux-cris-kernel@axis.com
Cc: linux-kernel@vger.kernel.org
Cc: linux-nfs@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: qla2xxx-upstream@qlogic.com
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: user-mode-linux-user@lists.sourceforge.net
Signed-off-by: NIngo Molnar <mingo@kernel.org>

this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: NAbdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: NMichael Büsch <m@bues.ch>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NMauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add new PCI IDs to cover newer Intel SoCs such as Braswell.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>