Some drivers cannot handle multiple retry rates specified by the rc
algorithm but instead use their own retry table (for example rt2800).
However, if such a device registers itself with a max_rates value of 1
the rc algorithm cannot make use of the extended information the device
can provide about retried rates. On the other hand, if a device
registers itself with a max_rates value > 1 the rc algorithm assumes
that the device can handle multi rate retries.

Fix this issue by introducing another hw parameter max_report_rates that
can be set to a different value then max_rates to indicate if a device
is capable of reporting more rates then specified in max_rates.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 8c0c709e
Author: Johannes Berg <johannes@sipsolutions.net>
Date:   Wed Nov 25 17:46:15 2009 +0100

    mac80211: move cmntr flag out of rx flags

moved the CMNTR flag into the skb RX flags for
some aggregation cleanups, but this was wrong
since the optimisation this flag tried to make
requires that it is kept across the processing
of multiple interfaces -- which isn't true for
flags in the skb. The patch not only broke the
optimisation, it also introduced a bug: under
some (common!) circumstances the flag will be
set on an already freed skb!

However, investigating this in more detail, I
found that most of the flags that we set should
be per packet, _except_ for this one, due to
a-MPDU processing. Additionally, the flags used
for processing (currently just this one) need
to be reset before processing a new packet.

Since we haven't actually seen bugs reported as
a result of the wrong flags handling (which is
not too surprising -- the only real bug case I
can come up with is an a-MSDU contained in an
a-MPDU), I'll make a different fix for rc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The old ieee80211_find_sta_by_hw method didn't properly
find VIFS when there was more than one per AP.  This caused
AMPDU logic in ath9k to get the wrong VIF when trying to
account for transmitted SKBs.

This patch changes ieee80211_find_sta_by_hw to take a
localaddr argument to distinguish between VIFs with the
same AP but different local addresses.  The method name
is changed to ieee80211_find_sta_by_ifaddr.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes stale mac80211_tx_control_flags for
filtered / retried frames.

Because ieee80211_handle_filtered_frame feeds skbs back
into the tx path, they have to be stripped of some tx
flags so they won't confuse the stack, driver or device.

Cc: <stable@kernel.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support to mac80211 for changing the interface
type even when the interface is UP, if the driver
supports it.

To achieve this
 * add a new driver callback for switching,
 * split some of the interface up/down code out
   into new functions (do_open/do_stop), and
 * maintain an own __SDATA_RUNNING bit that will
   not be set during interface type, so that any
   other code doesn't use the interface.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ieee80211_scan_completed() function was a frequent
source of potential deadlocks, since it is called by
drivers but may call back into drivers, so drivers had
to make sure to call it without any locks held, which
frequently lead to more complex code in drivers. Avoid
that problem by allowing the function to be called in
any context, and queueing the actual work it does.
Also update the documentation for it to indicate this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix spelling and readability of a few lines of kernel doc:

    s/issueing/issuing/g
    s/approriate/appropriate/g
    s/supported by simply/supported simply by/
    s/IEEE80211_HW_BEACON_FILTERING/IEEE80211_HW_BEACON_FILTER/g
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a small problem in the documentation for
ieee80211_request_smps, and a now erroneous
inclusion of enum ieee80211_key_alg, which no
longer exists after the change to ciphers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes we don't just need to know whether or
not the device is idle, but also per interface.
This adds that reporting capability to mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.

Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack.  That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure.  Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some features require knowing the DTIM period
before associating. This implements the ability
to wait for a beacon in mac80211 before assoc
to provide this value. It is optional since
most likely not all drivers will need this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For some drivers it can be useful to know whether the channel they're
supposed to switch to is going to be used for short off-channel work or
scanning, or whether the hardware is expected to stay on it for a while
longer. This is important for various kinds of calibration work, which
takes longer to complete and should keep some persistent state, even if
the channel temporarily changes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Network code uses the __packed macro instead of __attribute__((packed)).
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ever since

commit e1b3ec1a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Mon Mar 29 12:18:34 2010 +0200

    mac80211: explicitly disable/enable QoS

mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.

However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.

When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.

Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.

In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.

Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.

The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.

This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.

In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ps-qos latency handling is broken. It uses predetermined latency values
to select specific dynamic PS timeouts. With common AP configurations, these
values overlap with beacon interval and are therefore essentially useless
(for network latencies less than the beacon interval, PSM is disabled.)

This patch remedies the problem by replacing the predetermined network latency
values with one high value (1900ms) which is used to go trigger full psm. For
backwards compatibility, the value 2000ms is still mapped to a dynamic ps
timeout of 100ms.

Currently also the mac80211 internal value for storing user space configured
dynamic PSM values is incorrectly in the driver visible ieee80211_conf struct.
Move it to the ieee80211_local struct.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:

[   92.026800] =======================================================
[   92.030507] [ INFO: possible circular locking dependency detected ]
[   92.030507] 2.6.34-04781-g2b2c009e #85
[   92.030507] -------------------------------------------------------
[   92.030507] modprobe/5225 is trying to acquire lock:
[   92.030507]  ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[   92.030507]
[   92.030507] but task is already holding lock:
[   92.030507]  (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[   92.030507]
[   92.030507] which lock already depends on the new lock.
[   92.030507]
[   92.030507]
[   92.030507] the existing dependency chain (in reverse order) is:
[   92.030507]
[   92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[   92.030507]        [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[   92.030507]        [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[   92.030507]        [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[   92.030507]        [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[   92.030507]        [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]

[   92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[   92.030507]        [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[   92.030507]        [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[   92.030507]        [<ffffffff8105ecc6>] kthread+0x96/0xb0
[   92.030507]        [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[   92.030507]
[   92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[   92.030507]        [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[   92.030507]        [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[   92.030507]        [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[   92.030507]        [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[   92.030507]        [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]

The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.

The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a whole bunch of kernel-doc warnings
and errors that crop up when running it on
mac80211 and cfg80211; the latter isn't
normally done so lots of bit-rot happened.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

STA_NOTIFY_ADD and STA_NOTIFY_REMOVE have no users anymore,
and station addition/removal are indicated to drivers
using sta_add() and sta_remove(), which can sleep.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.

The debugfs code I recently added got this wrong
as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.

Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.

This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a single use of this struct member, but
as it is write-only it clearly not necessary.
Thus we can free up some space here, even if we
don't need it right now it seems pointless to
carry around the variable.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix kernel-doc warnings in mac80211.h:

Warning(include/net/mac80211.h:838): No description found for parameter 'ap_addr'
Warning(include/net/mac80211.h:1726): No description found for parameter 'get_survey'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 03ceedea.

This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 03ceedea, since it
breaks resume from suspend-to-ram on Rafael's Acer Ferrari One.
NetworkManager thinks everything is ok, but it can't connect to the AP
to get an IP address after the resume.

In fact, it even breaks resume for non-ath9k chipsets: reverting it also
fixes Rafael's Toshiba Protege R500 with the iwlagn driver.  As Johannes
says:

  "Indeed, this patch needs to be reverted. That mac80211 change is wrong
   and completely unnecessary."
Reported-and-requested-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Daniel Yingqiang Ma <yma.cool@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for offloading the channel switch
operation to devices that support such, typically
by having specific firmware API for it. The reasons
for this could be that the firmware provides better
timing or that regulatory enforcement done by the
device requires special handling of CSAs.

In order to allow drivers to specify the timing to
the device, the new channel_switch callback will
pass through the received frame's mactime, where
available.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, when one interface switches HT mode,
all others will follow along. This is clearly
undesirable, since the new one might switch to
no-HT while another one is operating in HT.

Address this issue by keeping track of the HT
mode per interface, and allowing only changes
that are compatible, i.e. switching into HT40+
is not possible when another interface is in
HT40-, in that case the second one needs to
fall back to HT20.

Also, to allow drivers to know what's going on,
store the per-interface HT mode (channel type)
in the virtual interface's bss_conf.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.

Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also remove associated IEEE80211_HW_NOISE_DBM from ieee80211_hw_flags.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some drivers (e.g. iwlwifi) need to know and try
to figure it out based on other things, but making
it explicit is definitely better.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Determine the dynamic PS timeout based on the configured ps-qos network
latency. For backwards wext compatibility, allow the dynamic PS timeout
configured by the cfg80211 to overrule the automatically determined value.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>