On CNL we may need to bump up the system agent voltage not only due
to CDCLK but also when driving DDI port with a sufficiently high clock.
To that end start tracking the minimum acceptable voltage for each crtc.
We do the tracking via crtcs because we don't have any kind of encoder
state. Also there's no downside to doing it this way, and it matches how
we track cdclk requirements on account of pixel rate.

v2: Allow disabled crtcs to use the min voltage
    Add IS_CNL check to intel_ddi_compute_min_voltage() since
    we're using CNL specific values there
    s/intel_compute_min_voltage/cnl_compute_min_voltage/ since
    the function makes hw specific assumptions about the voltage
    values
v3: Drop the test hack leftovers from skl_modeset_calc_cdclk()
v4: s/voltage/voltage_level/ (Rodrigo)
    Replace DPLL DVFS FIXMEs with an explanation why we don't
    do anything there (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-9-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on CNL. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-8-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on BXT/GLK. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-7-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on SKL/KBL/CFL. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-6-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on BDW. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: Keep the WARN_ON (Rodrigo)
v3: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-5-ville.syrjala@linux.intel.com

Store the punit DSPFREQUAR value into cdclk_state->voltage on
VLV/CHV. Since we can actually read that out from the hardware
this can give us a bit more cross checking between the hardware
and software state.

v2: Don't break waiting for cdclk change on VLV/CHV
v3: Split out the cdclk sanity check in vlv_set_cdclk() (Rodrigo)
v4: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-4-ville.syrjala@linux.intel.com

For CNL we'll need to start considering the port clocks when we select
the voltage level for the system agent. To that end start tracking the
voltage in the cdclk state (since that already has to adjust it).

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-3-ville.syrjala@linux.intel.com

Redo some switch statements in the cdclk code to use a common
fall through for the default case. Makes everything look a bit
more uniform

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-2-ville.syrjala@linux.intel.com

The latest version of DMC on CNL is 1.06.
Update the version so as to load the
latest firmware.

Release Notes:
Version: 1.06
1. DDI and AUX IO related fix.

v2: Improve the prefixes in commit message.
Add Release Notes directly. (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507053588-677-1-git-send-email-anusha.srivatsa@intel.com

On CNL, individual wake rate limit was added to each engine.

GT can only go to RC6 if both Render and Media engines are
individually qualified. So we need to set their individual
wake rate limit.

+-----------------+---------------+--------------+--------------+
|                 |    GT RC6     |  Render C6   |   Media C6   |
+-----------------+---------------+--------------+--------------+
| Wake rate limit | 0xA09C[31:16] | 0xA09C[15:0] | 0xA0A0[15:0] |
+-----------------+---------------+--------------+--------------+

v2: - Tune Render and Media wake rate values according to some extra
      info I got from HW engineers. Value can be tuned, but for now
      these are the recommended values.
    - Fix typos pointed by James.

Cc: Nathan Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023224612.27208-1-rodrigo.vivi@intel.com

As we faced in BXT, on CNL DDI_A_4_LANES is not
set as expected when system is boot with multiple
monitors connected. This result in wrong lane
setup impacting the max data rate available and
consequently blocking modeset on eDP, resulting
in a blank screen.

Most of CNL SKUs don't support DDI-E.
The only SKU that supports DDI-E is the same
that supports the full A/E split called DDI-F.

Also when DDI-F is used DDI-E cannot be used because
they share Interrupts. So DDI-E is almost useless.
Anyways let's consider this is possible and rely on
VBT for that.

This patch was initialy start by Clint, but required
many changes including full commit message. So
Credits entirely to Clint for finding this.

v2: Extract all messy conditions into a helper function
    as suggested by Ville.
    Along with simplification I removed the debug
    message on the working case since now all conditions
    are grouped.
v3: Split the conditions even more as suggested by Ville.
    Get's cleaner and easier to add new cases in the
    future.
Suggested-by: NClint Taylor <clinton.a.taylor@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023173920.22890-1-rodrigo.vivi@intel.com

The compat callback was missing and triggered failures in 32bits
userspace when enabling/disable the perf stream. We don't require any
particular processing here as these ioctls don't take any argument.
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: eec688e1 ("drm/i915: Add i915 perf infrastructure")
Cc: linux-stable <stable@vger.kernel.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024152728.4873-1-lionel.g.landwerlin@intel.com

Originally we set the priority to max upon inserting the request into
the execlists queue (and removing it from the scheduler lists). We could
then use the prio==INT_MAX as a shortcut within execlists_schedule() to
detect the end of the dependency chain. Since commit 1f181225
("drm/i915/execlists: Keep request->priority for its lifetime") this is
no longer true as we use the request completion as an indicator the
schedule dependency chain is complete instead. (This allows us to then
reschedule requests even when its context is in flight.) However, this
makes the GEM_BUG_ON() inside execlists_schedule() racy as we may change
the rq->prio at the same time. As the assertion is useful, let's keep
the assertion and remove the micro-optimisation.

Fixes: 1f181225 ("drm/i915/execlists: Keep request->priority for its lifetime")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024115501.21033-1-chris@chris-wilson.co.ukReviewed-by: NMichał Winiarski <michal.winiarski@intel.com>

Back in commit a4b2b015 ("drm/i915: Don't mark an execlists
context-switch when idle") we noticed the presence of late
context-switch interrupts. We were able to filter those out by looking
at whether the ELSP remained active, but in commit beecec90
("drm/i915/execlists: Preemption!") that became problematic as we now
anticipate receiving a context-switch event for preemption while ELSP
may be empty. To restore the spurious interrupt suppression, add a
counter for the expected number of pending context-switches and skip if
we do not need to handle this interrupt to make forward progress.

v2: Don't forget to switch on for preempt.
v3: Reduce the counter to a on/off boolean tracker. Declare the HW as
active when we first submit, and idle after the final completion event
(with which we confirm the HW says it is idle), and track each source
of activity separately. With a finite number of sources, it should aide
us in debugging which gets stuck.

Fixes: beecec90 ("drm/i915/execlists: Preemption!")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-3-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

When we park the engine (upon idling), we kill the irq tasklet. However,
to be sure that it is not restarted by a spurious interrupt after doing so,
flush the interrupt handler before parking. As we only park the engines
when we believe the system is idle, there should not be any interrupts to
distrub us; so flushing the final in-flight interrupt should be sufficient.
(However, we are still dependent on the HW behaving in an orderly and
timely fashion, which we shall endeavour to improve upon later.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-2-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

In the idle worker we drop the prolonged GT wakeref used to cover such
essentials as interrupt delivery. (When a CS interrupt arrives, we also
assert that the GT is awake.) However, it turns out that 10ms is not
long enough to be assured that the last CS interrupt has been delivered,
so bump that to 200ms, and move the entirety of that wait to before we
take the struct_mutex to avoid blocking. As this is now a potentially
long wait, restore the earlier behaviour of bailing out early when a new
request arrives.

v2: Break out the repeated check for new requests into its own little
helper to try and improve the self-commentary.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-1-chris@chris-wilson.co.uk

Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Starting on CNL we now need to map VBT DDC Pin to
BSPec DDC Pin values. Not a direct translation anymore.

According to VBT
Block 2 (General Bytes Definition)
DDC Bus

+----------+-----------+--------------------+
| DDI Type | VBT Value | Bspec Mapped Value |
+----------+-----------+--------------------+
| DDI-B    | 0x1       | 0x1                |
| DDI-C    | 0x2       | 0x2                |
| DDI-D    | 0x3       | 0x4                |
| DDI-F    | 0x4       | 0x3                |
+----------+-----------+--------------------+

v2: Move defines to a better place.
    This is actually CNL_PCH not CNL only.
v3: Accepting Ville's suggestions: enums and array to
    to make this future proof.
v4: Protect the array access as Ville suggested.
    Also accepting all Jani's suggestions:
    	      - use already defined gmbus pin definitions.
	      - use map_ddc_pin for disambiguation.
	      - Add /* sic */ comment on inverted values
	      	so people can easily see it it nos a mistake
		we have the map 3 -> 4 and 4 -> 3 :/

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171020172641.16029-1-rodrigo.vivi@intel.com

No functional change expected. Just let's use this enum
when possible and also same standard pll_id name
so we can rework gen9+ port clock later.

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018195407.8618-1-rodrigo.vivi@intel.com

This patch re-use already parsed DSI backlight/cabc ports
info for saving it inside struct intel_dsi rather than
parsing it at the time of DSI initialization.

V2: Remove backlight and cabc variable initialization (Jani N).
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507898700-20016-2-git-send-email-madhav.chauhan@intel.com

This patch parse DSI backlight/cabc ports info from
VBT and save them inside local structure. This saved info
can be directly used while initializing DSI for different
platforms instead of parsing for each platform.

V2: Changes:
    - Typo fix in commit message.
    - Move up newly added port variables (Jani N)
    - Remove redundant initialization (Jani N)
    - Don't parse CABC ports if not supported (Jani N)
V3: Patch restructure (Suggested by Jani N)

Credits-to: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507898700-20016-1-git-send-email-madhav.chauhan@intel.com

If the device is in runtime suspend, resuming takes time and reduces our
powersaving. If this was for a small write into an object, that resume
will take longer than any savings in using the indirect GGTT access to
avoid the cpu cache.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019063733.31620-1-chris@chris-wilson.co.uk

Only the DDI hook has some actual content.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017140313.20937-1-jani.nikula@intel.com

They're unused and unsupported. Leave the reduced_clock pointers in
place still, should they prove useful later on.

v2: go from nuking DDI lowfreq_avail to nuking it entirely (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017140234.20677-1-jani.nikula@intel.com

A bunch of functions are now exclusively used for HDMI, so naming the
variables with hdmi prefix/suffix is redundant. Also use int rather
than u32 for the translation level consistently.

v2: Rebase due to hdmi_level=-1 avoidance

Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018181958.4423-1-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

Handle missing buf trans tables, or out of bounds buf trans levels
the same way everywhere. These should never be hit under normal
conditions, but let's play it safe for now.

v2: Avoid the hdmi_level=-1 case (James)

Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018181934.4229-1-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

SKL DDI B/C/D only have 9 usable buf trans registers for DP/eDP. That
matches the normal DP buf trans tables, but the low vswing eDP tables
have 10 entries. Thus the eDP tables can only be used safely with DDI A
and E.

We try to catch cases where DDI B/C/D gets used with the wrong number of
entires in some parts of the code, but not everywhere. Let's move the
code to deal with that deeper into intel_ddi_get_buf_trans_edp(). And
for sake of symmetry do the same in intel_ddi_get_buf_trans_dp(). That
would also avoid explosions in the rather unlikely case that the DP
tables would get revised to 10 entries as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-9-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

default_index contained in the BXT buf_trans tables is actually useless.
For DP we should always have a valid level selected (otherwise the link
training logic would be buggy), and for HDMI we can just do what the
other platforms do and pick the correct entry in intel_ddi_hdmi_level().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-8-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

encoder->type is unreliable for DP/HDMI, so pass it in explicity into
cnl_ddi_vswing_sequence(). This matches what we do for BXT.

v2: Pass intel_encoder down to cnl_ddi_vswing_program(), and
    clean up the argument types while at it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-7-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

Make BXT less special by following the CNL approach and handling
it in intel_ddi_dp_voltage_max() alognside every other DDI platform.

v2: Clean up the argument types to bxt_ddi_vswing_sequence() while at it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-6-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

The caller of intel_prepare_hdmi_ddi_buffers() alreday figured out the
level, so let's just pass it in instead if figuring it out again.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-5-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

encoder->type isn't reliable for DP/HDMI encoders, so pass the type
explicity to skl_set_iboost(). Also take the opportunity to streamline
the code.

v2: Clean up the argument types to skl_ddi_set_iboost() while at it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-4-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

Introduce intel_ddi_get_buf_trans_hdmi() and start using it where we
can.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-3-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>

We'll want to use the intel_ddi_get_buf_trans_*() functions a bit
earlier in the file, so move them up. While at it start using them
in the iboost setup to get rid of the platform checks there.

v2: Rebase due to BDW FDI buf trans fix
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-2-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

After being requested to idle the GPU, flush the idle worker to drop the
residual active state, and any internal object caches.

v2: By popular demand, introduce DROP_IDLE for fine-grained control from
userspace, though it should be used as part of a
	DROP_ACTIVE | DROP_RETIRE | DROP_IDLE | DROP_FREED
sequence.
v3: Convert to BIT() to sell it to Joonas.

References: https://bugs.freedesktop.org/show_bug.cgi?id=102655Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018121621.10824-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This is to use clipped y coordinate here. I left get_crtc_fence_y_offset()
function itself in place as oneliner to maintain comment above it why this
is done.
Signed-off-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508270891-22186-6-git-send-email-juhapekka.heikkila@gmail.com

Don't handle skylake primary plane separately as it is similar
plane as the others.
Signed-off-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508270891-22186-5-git-send-email-juhapekka.heikkila@gmail.com

Don't handle skylake primary plane separately as it is similar
plane as the others.
Signed-off-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508270891-22186-4-git-send-email-juhapekka.heikkila@gmail.com

Move u32 dspaddr_offset from struct intel_crtc member into local
variable in i9xx_update_primary_plane()
Signed-off-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508270891-22186-3-git-send-email-juhapekka.heikkila@gmail.com

Move adjusted_x/y from crtc to fbc cache.
Signed-off-by: NJuha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508270891-22186-2-git-send-email-juhapekka.heikkila@gmail.com
[vsyrjala: Add rudimentary commit message]
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>